• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 추계 학술논문 발표대회
• /
• pp.34-35
• /
• 2013

In this study, the ultra high strength concrete which have 80, 130, 180MPa took the heat from 20℃ to 700℃ and the 0, 20% stress in normal condition's to evaluate stress-strain, residual compressive strength and thermal expansion deformation were evaluated. The heating speed of specimen was 0.77℃/min 20~50℃, 50℃ before the target temperature, and the other interval's heating speed was 1℃/min. As a result, the stress-strain curve of non-load specimen showed the liner behavior at high temperature when the specimen's strength increased more. If ultra high strength concrete got loads, its compressive strength tended to decrease different from the normal strength concrete. The thermal expansion deformation was expanded from a vitrification of quartz over 500℃. however, over the 600℃, it was shrinked because of the dehydration of the combined water.

• 터널과지하공간
• /
• 제9권4호
• /
• pp.350-363
• /
• 1999

주기전단하중 하의 암석 절리에 대한 역학적 거동을 규명하기 위해 정밀 주기전단시험 장치를 설계·제작하였다. 실험실에서 황등화강암과 여산대리석 인공 절리 시료로 펑면절리와 거친 절리에 대해 일련의 주기전단시험을 실시하였다. 시료에 대한 레이저 변위계를 이용한 3차원 거칠기 측정을통해 절리의 거칠기 특성을규명하였다. 주기전단시험 결과를 통해 주기전단 과정의 단계별 거동 특성과하중과제하시의 거동 차이, 전단거동의 이방성 등을고찰하였다. 거친 절리면의 역학적 거동 특성은 주로 2차 거칠기의 영향과 암석 재료의 높은 강도에 영향을 받았다. 주기전단시 거친 절리에 대한 돌출부 손상이 지수적인 거칢각 손상 법칙을 따름을 실험적으로 검증하였으며, 수직응력파 거칠기 종류, 하중 단계에 따라 돌출부들의 손상 기구가 다름을 확인하였다.

• The Journal of Advanced Prosthodontics
• /
• 제7권2호
• /
• pp.160-165
• /
• 2015

PURPOSE. In this study, a temporal abutment fixation screw, designed to fracture in a controlled way upon application of an occlusal force sufficient to produce critical micromotion was developed. The purpose of the screw was to protect the osseointegration of immediate loaded single implants. MATERIALS AND METHODS. Seven different screw prototypes were examined by fixing titanium abutments to 112 Mozo-Grau external hexagon implants (MG Osseous$^{(R)}$; Mozo-Grau, S.A., Valladolid, Spain). Fracture strength was tested at $30^{\circ}$ in two subgroups per screw: one under dynamic loading and the other without prior dynamic loading. Dynamic loading was performed in a single-axis chewing simulator using 150,000 load cycles at 50 N. After normal distribution of obtained data was verified by Kolmogorov-Smirnov test, fracture resistance between samples submitted and not submitted to dynamic loading was compared by the use of Student's t-test. Comparison of fracture resistance among different screw designs was performed by the use of one-way analysis of variance. Confidence interval was set at 95%. RESULTS. Fractures occurred in all screws, allowing easy retrieval. Screw Prototypes 2, 5 and 6 failed during dynamic loading and exhibited statistically significant differences from the other prototypes. CONCLUSION. Prototypes 2, 5 and 6 may offer a useful protective mechanism during occlusal overload in immediate loaded implants.

• Journal of Biosystems Engineering
• /
• 제17권3호
• /
• pp.260-271
• /
• 1992

Fruits are generally subjected to mechanical forces during harvesting, handling, and transportation that may cause damage in the form of bruises, punctures, and cracks. In order to prevent damage, and insure better quality fruits for consumers, it is very essential to study physical properties of these materials. The studies were conducted to examine the effect of storage period, storage condition, and other factors, such as loading rate and initial strain, on the stress relaxation behavior of the fruit flesh, and develop nonlinear viscoelastic models to represent its stress relaxation behavior. The following results were obtained from the study : 1. Since the viscoelastic behavior of the fruits flesh was nonlinear, the behavior was satisfactorily modelled as follows ; $${\delta}({\varepsilon},\;t)={\varepsilon}^A[B\;{\exp}(-Ct)+D\;{\exp}(-Ft)+G(-Ht)]$$ But, for the every strain applied, the stress relaxation behavior of the fruit flesh, such as apple and pear, could be well described by the Generalized Maxwell model, respectively. 2. The effect of loading rate on the stress relaxation behavior was remarkable. The higher loading rate resulted in the higher initial stress, and the faster stress relaxation. 3. The higher initial strain resulted in the higher initial stress, and stress relaxed at the large initial strain was also much higher than at the small initial strain. 4. Stress relaxation rate and quantity stored in the fruits at the low temperature storage were much higher than those at the normal temperature storage in the same storage period. Also, in all fruits tested, the longer storage period was the more relaxation rate and quantity were shown. These trends in the normal temperature condition was the more significant than in the low temperature condition.

• 대한기계학회논문집A
• /
• 제35권10호
• /
• pp.1281-1289
• /
• 2011

본 논문에서는 소형풍력발전시스템 블레이드 제작에 사용되는 복합재료의 피로수명 데이터에 대한 통계적 해석을 위하여 다양한 확률분포 모델의 적합성에 대한 연구를 수행하였다. 이를 위하여 삼축 유리섬유강화 복합재료를 대상으로 0$^{\circ}C$, 45$^{\circ}C$ 및 90$^{\circ}C$ 의 하중방향에 대한 인장시험을 실시하였다. 또한 상기의 하중방향에 대하여 4 수준의 피로응력준에서의 피로시험을 수행하였다. 이를 통하여 획득한 피로수명 데이터를 대상으로 1) 전체 적합성, 2) 끝단 적합성 및 3) 피로물리 일치성의 기준을 이용하여 2 모수 Weibull, 3 모수 Weibull, 정규 및 대수정규분포의 적합성을 평가하였다. 또한 피로수명의 분산에 대한 하중방향 및 피로응력의 영향 역시 검토하였다.

• 한국운동역학회지
• /
• 제28권2호
• /
• pp.135-141
• /
• 2018

Objective: The purpose of this study was to investigate the effect of functional ankle instability (FAI) and surgical treatment (ST) on postural stability and leg stiffness during vertical-drop landing. Method: A total of 21 men participated in this study (normal [NOR]: 7, FAI: 7, ST: 7). We estimated dimensionless leg stiffness as the ratio of the peak vertical ground reaction force and the change in stance-phase leg length. Leg length was calculated as the distance from the center of the pelvis to the center of pressure under the foot. Furthermore, the analyzed variables included the loading rate and the dynamic postural stability index (DPSI; medial-lateral [ML], anterior-posterior [AP], and vertical [V]) in the initial contact phase. Results: The dimensionless leg stiffness in the FAI group was higher than that of the NOR group and the ST group (p = .018). This result may be due to a smaller change in stance-phase leg length (p = .001). DPSI (ML, AP, and V) and loading rate did not show differences according to the types of ankle instability during drop landing (p > .05). Conclusion: This study suggested that the dimensionless leg stiffness was within the normal range in the ST group, whereas it was increased by the stiffness of the legs rather than the peak vertical force during vertical-drop landing in the FAI group. Identifying these potential differences may enable clinicians to assess ankle instability and design rehabilitation protocols specific for the impairment.

• Geomechanics and Engineering
• /
• 제29권2호
• /
• pp.155-170
• /
• 2022

An accurate analysis of structures supported on soft soils and subjected to seismic loading requires the consideration of the soil-foundation-structure interaction. An important aspect of this interaction lies with the energy dissipation due to soil material damping. Unlike advanced constitutive models that can induce energy loss, the use of simple elastoplastic constitutive models requires additional damping. The frequency dependent Rayleigh damping is a formulation that is frequently used in dynamic analysis. The main concern of this formulation is the correct selection of the target damping ratio and the frequency range where the response is frequency independent. The objective of this study is to investigate the effects of the Rayleigh damping parameters in soil-pile-structure and soil-inclusion-platform-structure systems in the presence of soft soil under seismic loading. Three-dimensional analyses of both systems are carried out using the finite difference software Flac3D. Different values of target damping ratios and minimum frequencies are utilized. Several earthquakes are used to study the influence of different excitation frequencies in the systems. The soil response in terms of accelerations, displacements and strains is obtained. For the rigid elements, the results are presented in terms of bending moments and normal forces. The results show that when the frequency of the input motion is close to the minimum (central) frequency in the Rayleigh damping formulation, the overdamping amount is reduced, and the surface spectral acceleration of the analyzed pile and inclusion systems increases. Thus, the bending moments and normal forces throughout the piles and inclusions also increase.

• Structural Engineering and Mechanics
• /
• 제22권3호
• /
• pp.311-330
• /
• 2006

Standard compression tests of steel fiber reinforced concrete (SFRC) cylinders are conducted to formulate compressive stress versus compressive strain relationship of SFRC. Axial pullout tests of SFRC specimens are also conducted to explore its tensile stress strain relationship. Cover concrete spalling and reinforcement buckling models developed originally for normal reinforced concrete are modified to extend their application to SFRC. Thus obtained monotonic material models of concrete and reinforcing bars in SFRC members are combined with unloading/reloading loops used in the cyclic models of concrete and reinforcing bars in normal reinforced concrete. The resulting path-dependent cyclic material models are then incorporated in a finite-element based fiber analysis program. The applicability of these models at member level is verified by simulating cyclic lateral loading tests of SFRC columns under constant axial compression. The analysis using the proposed SFRC models yield results that are much closer to the experimental results than the analytical results obtained using the normal reinforced concrete models are.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 춘계 학술논문 발표대회
• /
• pp.255-256
• /
• 2012

In this study, strain properties of high strength concrete using light weight aggregate which is widely used in recent years are evaluated. For these purpose, thermal strain, transient creep were measured in prestressed condition as 0, 20, 40% of specimen strength at target temperature with 60MPa specimens which was using normal and light weight aggregate. As a result, light weight aggregate is more advantageous for the control of strain than normal aggregate because of its low thermal expansion.

• Journal of Periodontal and Implant Science
• /
• 제24권1호
• /
• pp.178-184
• /
• 1994

This study was undertaken to examine the protein content of GCF and serum from noraml population in order to standardize the sample loading on SDS/PAGE gels. The resulats were as follows ; 1. The protein concentration of serum was not different between normal group and diseased group. 2. In GCF, the bands of lower molecular weight than albumin were heavily stained, but in serum, the protein bands of higher molecalar weight were found. 3. The profile of protein in normal GCF was characterized by heavily staining bands at 77, 66, 55, 26 KDa corresponding to the positions of transferrin, albumin, heavy and light chains of Ig G. Also 47, 37 KDa nonplasma proteins were found.