• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(I)
• /
• pp.171-174
• /
• 2005

In this study, new moment-resisting precast concrete beam-column joint is proposed for moderate seismic regions. It has the connection reinforcing bars, penetrated the joint and lap-spliced with the bottom bars of precast U-beam. To evaluate the performance for noncontact lapped splice, analytical works were conducted. Major variables for FEM analysis are the length of lap, the diameter of connection reinforcing bars, and the distance between lapped bars. The results of this study show thar the these variables has much influence on strength and deformation of lapped joint.

• 동력기계공학회지
• /
• 제10권4호
• /
• pp.181-186
• /
• 2006

In this paper, a noncontact type torque meter using silicone rubber to measure the exact torque value and reduce a vibration and a noise, was developed. When planetary gear speed reducer runs, torque, RPM etc.. of motor change according to load or speed change. So, it needs a device to detect load's change or to diagnose the state of thewhole drive department by monitoring these result values. The noncontact type torque meter using silicone rubber that we're trying to develop this time is low-cost and can measure RPM and torque value simply. Also, it caculate a power using this value and indicate them on screen.

• Smart Structures and Systems
• /
• 제24권5호
• /
• pp.597-606
• /
• 2019

Damage detection based on dynamic characteristics of a structure is one of important roles in structural damage identification. It is difficult to detect local structural damage using traditional dynamic experimental methods due to a limited number of sensors used in an experiment. In this work, a non-contact test stand of fan blades is established, and a full-field noncontact test method, combined with three-dimensional digital image correlation, Bayesian operational modal analysis, and damage indices, is used to detect local damage of a fan blade under ambient excitation without use of baseline information before structural damage. The methodology is applied to detect invisible local damage on the fan blade. Such a method has a seemingly high potential as an alternative to detect local damage of blades with complex high-precision surfaces under extreme working conditions because it is a noncontact test method and can be used under ambient excitation without human participation.

• 한국구조물진단유지관리공학회지
• /
• 제18권1호
• /
• pp.27-36
• /
• 2014

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.731-732
• /
• 2010

• 한국농림기상학회:학술대회논문집
• /
• 한국농림기상학회 2011년도 학술발표회
• /
• pp.48-48
• /
• 2011

• 한국철도학회논문집
• /
• 제15권4호
• /
• pp.376-380
• /
• 2012

IPMSM의 구동 중에 발생되는 철손은 코어 재료 특성에 의해 크게 좌우되며, 일반적으로 회전형 전동기에서는 모든 자속의 흐름 방향으로 자기적 특성이 동일한 무방향성 전기강판이 코어 재료로 사용된다. 무방향성 전기강판과 비교하여 방향성 전기강판은 자속의 흐름 방향으로의 자기적 특성이 우수한 장점을 가지고 있다. 따라서 본 연구에서는 IPMSM의 철손을 저감시키기 위하여 코어 재료로써 무방향성 전기강판과 방향성 전기강판을 동시에 사용하는 구조를 제안하였다. IPMSM의 고정자에 자속 흐름의 방향으로 가공된 방향성 전기강판을 이용한 분할 티스 구조를 적용함으로써 기존의 110kW급 IPMSM과 비교하여 거의 40% 정도의 철손 저감 효과를 얻을 수 있었다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2009년도 정보 및 제어 심포지움 논문집
• /
• pp.357-359
• /
• 2009

In this paper, the 2.4GHz doppler radar system consisting of the doppler radar module and a baseband module were designed to detect heartbeat and respiration signal without direct skin contact. A bio-radar system emits continuous RF signal of 2.4GHz toward human chest, and then detects the reflected signal so as to investigate cardiopulmonary activities. The heartbeat and respiration signals acquired from quadrature signal of the doppler radar system are applied to the pre-processing circuit, amplification circuit, and the offset circuit of the baseband module. ECG(electrocardiogram) and reference respiration signals are measured simultaneously to evaluate the doppler radar system. As a result, the respiration signal of doppler radar signal is detected to 1m without complex digital signal processing. The sensitivity and calculated from I/Q respiration signal were $98.29{\pm}1.79%$, $97.11{\pm}2.75%$, respectively, and positive predictivity were $98.11{\pm}1.45%$, $92.21{\pm}10.92%$, respectively. The sensitivity and positive predictivity calculated from phase and magnitude of the doppler radar were $95.17{\pm}5.33%$, $94.99{\pm}5.43%$, respectively. In this paper, we confirmed that noncontact real-time heartbeat and respiration detection using the doppler radar system has the possibility and limitation.

• 동력기계공학회지
• /
• 제15권2호
• /
• pp.13-18
• /
• 2011

This thesis is about the result of conducting a specific experiment for the development of noncontact vibration displacement sensor for measuring the spindle vibration that is used for conditional monitoring of machinery. One should be careful when using the eddy current type displacement sensor because the sensitivity of it is different according to the quality of the material. While the probe used for nondestructive inspection adopts the effect of transmitting the material by using the high frequency domain, the eddy current type displacement sensor uses the lower frequency of around 1MHz. Also, while the nondestructive probe uses the method of enhancing output by using the resonance zone, the vibration displacement sensor utilizes the stable zone by avoiding the resonance zone. Since the oscillator of the converter uses the "L" element as Probe, its characteristic changes with the variation of a relevant impedance. In other words, if the length of Probe's Cable gets extended (Impedance increase), the sensitivity declines accordingly. The effect of surrounding temperature was small, but the influence of the quality of Sensor Coil used was high. Moreover, following an experimental demonstration of the phenomenon where the sensitivity decreases as the frequency of the tested material increases from a frequency response test, the maximum frequency that could be measured was approximately 1KHz. It was noted that the degree of precision could be maintained by using the gap of the probe in the linear zone at the installation site.

• 한국산학기술학회논문지
• /
• 제14권1호
• /
• pp.45-50
• /
• 2013

Photopia를 활용하여 적외선 램프 반사부의 각 형상에 대한 조도 분포를 해석하여 최적인 원호 형상으로 설계하였다. 적외선 온도센서를 통해 태양전지셀의 솔더링 온도를 피드백 받아서 설정된 솔더링 온도 프로파일과의 오차를 제어값으로서 IR 램프의 전류를 실시간으로 제어하는 솔더링 온도의 폐루프 제어시스템을 구현하였다. HMI 조작반에 의해 쉽게 운전되고, PLC와 IR 램프 제어기에 의하여 강인하게 제어되는 IR 램프 열원을 사용한 태양전지셀의 비접촉식 솔더링 장치를 개발하였다.