• 한국자동차공학회논문집
• /
• 제24권5호
• /
• pp.538-548
• /
• 2016

The purpose of this study is to identify the possibility of effective tuning works, understand the characteristics of tuning engine, and analyse the basic data of engine tuning inspection corresponding to the safe operation and environment of a driving gasoline car. The effects of tuning on the characteristics of performance and exhaust emissions under a wide range of engine speeds are experimentally investigated by the actual driving car with a four-cycle, four-cylinder DOHC, turbo-intercooler, water-cooled gasoline engine operating at four types of non-tuning, tuning 1, 2 and 3. The tuning parts in the gasoline engine are the intake manifold, intake pipe and air filter. In the experiment, the output, torque and air-fuel ratio of the five-speed automatic transmission vehicles were measured at the chassis dynamometer(Dynojet 224xLC) with one person on board. The exhaust emissions of $NO_X$, THC, CO, $O_2$ and $CO_2$, and excess air ratio(${\lambda}$) at the other chassis dynamometer(DASAN-MD-ASM-97-KR-HD) were also measured by the idle/constant-speed mode(ASM2525 mode) test method. It is found that the actual air-fuel ratios of non-tuning and tuning engines were shown to be lower than the stoichiometric air-fuel ratio with increasing engine speed, and the actual air-fuel ratio of non-tuning engine was slightly higher than those of tuning engines when the engine speed is more than 4000 rpm. The output was significantly increased by the tuning whereby the maximum output of tuning engine was more increased to approximately 117.64% than that of non-tuning engine. In addition, CO, THC and $NO_X$ emissions of non-tuning and tuning engines measured by the constant-speed test mode were all satisfied with the inspection standards. CO emission was increased, while THC and $NO_X$ emissions were reduced by tuning.

• 대한기계학회논문집B
• /
• 제41권11호
• /
• pp.775-784
• /
• 2017

본 연구의 목적은 운행자동차에 있어서 안전운행과 환경에 문제가 없는 효과적인 엔진튜닝의 작업가능성을 확인하고, 튜닝엔진의 특징을 파악하여 엔진튜닝 검사의 기초자료를 분석하는 것이다. 비튜닝 및 튜닝 엔진 2-1, 2-2, 2-3의 4종류에 대한 넓은 범위의 엔진회전수 하에서 4행정, 4기통 DOHC, 터보 인터쿨러, 수냉 가솔린엔진의 실제 운행자동차를 사용하여 공연비 및 성능 특성에 미치는 튜닝엔진의 효과를 실험적으로 조사했다. 운행 가솔린자동차에 대한 엔진의 튜닝 부분은 흡기 다기관, 흡기 파이프, 공기필터, 배기 다기관, 배기 파이프 및 소음기를 포함한다. 1인이 탑승한 5단 자동변속기를 갖는 운행 가솔린자동차 비튜닝 및 튜닝 엔진의 공연비 및 토크는 차대 동력계(Dynojet 224xLC)에 의하여 실험에 의해 측정하였다. 운행 가솔린자동차 튜닝엔진의 최대 토크는 비튜닝엔진보다 평균 103.68% 만큼 증가되었고, 튜닝엔진의 최대 출력은 비튜닝엔진보다도 평균 119.68% 만큼 증가되었음을 알았다.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3315-3325
• /
• 1994

To study the variation of charging efficiency in the engine intake, the method to change the natural frequency of intake system using the intake control valve was studied and it has been used in actual engine to increase the intake air. In this paper, the method of characteristics was used to analyze the non-steady state and compared with the experimental data of the 6-cylinder diesel engine showing the effectiveness of the method theoretically.

• 동력기계공학회지
• /
• 제13권5호
• /
• pp.82-88
• /
• 2009

The purpose of this paper is to provide technical background, techniques and actual diesel engine signature analysis evaluation result. Engine signature analysis(ESA) is a process for monitoring the material condition of diesel engine using external sensors, eliminating the need to periodically disassemble the engine. ESA is also used to balanced the engine. Engine balancing is the process of tuning the engine so that all cylinders carry equal load. ESA is a useful tool to non-intrusively determine the operability and performance and assessment of the material condition of internal component of a diesel engine.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.132-139
• /
• 2008

The blade vibration problem of bladed disk is the most critical subject to consider since it directly affects the stable performance of the engine as well as life of the engine. Especially, due to complicated vibration pattern of the bladed disk, more effort was required for vibration analysis and test. The research of measuring the vibration of the bladed disk, using NSMS(Non-intrusive stress measurement) instead of Aeromechanics testing method requiring slip ring or telemetry system with strain gauge, was successful. These testing can report the actual stresses seen on the blades; detect synchronous resonances that are the source of high cycle fatigue (HCF) in blades; measure individual blade mis-tuning and coupled resonances in bladed disks. In order to minimize the error being created due to heat expansion, the tip timing sensor is installed parallel to the blade trailing edge, yielding optimal result. Also, when working on finite element analysis, the whole bladed disk has gone through three-dimensional analysis, evaluating the family mode. The result of the analysis matched well with the test result.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.871-876
• /
• 2008

The blade vibration problem of bladed disk is the most critical subject to consider since it directly affects the stable performance of the engine as well as life of the engine. Especially, due to complicated vibration pattern of the bladed disk, more effort was required for vibration analysis and test. The research of measuring the vibration of the bladed disk, using NSMS(Non-intrusive stress measurement) instead of Aeromechanics testing method requiring slip ring or telemetry system with strain gauge, was successful. These testing can report the actual stresses seen on the blades; detect synchronous resonances that are the source of high cycle fatigue(HCF) in blades; measure individual blade mis-tuning and coupled resonances in bladed disks. In order to minimize the error being created due to heat expansion, the tip timing sensor is installed parallel to the blade trailing edge, yielding optimal result. Also, when working on finite element analysis, the whole bladed disk has gone through three-dimensional analysis, evaluating the family mode. The result of the analysis matched well with the test result.

• 대한전기학회논문지
• /
• 제38권8호
• /
• pp.617-628
• /
• 1989

In systematic tuning of digital STC parameters, systems with time-varying parameters and systems with time-varying delays are studied individually because of many preconditions and difficulties. In order to eliminate all these difficulties effectively, the expert control technique is required to enhance STC control functions. In this paper, an expert controller, a STC utilizing expert control technique, for process control is designed. The expert controller is composed of an unstability indicator for detecting plant unstability, an expert back-up controller and an expert STC which are switched each other by the unstability indication, and expert system with knowledge base and inference engine. This expert controller is able to perform control functions successfuly for the following` 1) a system which has unknown and time-varying delay time, 2) a time-varying system which has unknown parameters, and 3) a system with minimun and non-minimum phase. The robust control function is demonstrated by computer simulations.

• International Journal of Automotive Technology
• /
• 제7권1호
• /
• pp.91-99
• /
• 2006

The diesel Auxiliary Power Unit (APU) for vehicle applications is a complex nonlinear system. For the purpose of this paper presents a dynamic average model of the whole system in an entirely physical way, which accounts for the non-ideal behavior of the diode rectifier, the nonlinear phenomena of generator-rectifier set in an elegant way, and also the dynamics of the dc load and diesel engine. Simulation results show the accuracy of the model. Based on the average model, a simple PI control scheme is proposed for the multivariable system, which includes the steps of model linearization, separate PI controller design with robust tuning rules, stability verification of the overall system by considering it as an uncertain one. Finally it is tested on a detailed switching model and good performances are shown for both set-point following and disturbance rejection.