• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.11-13
• /
• 2019

This paper proposes a novel high step-up non-isolated DC-DC converter, suitable for regulating dc bus in various inherent low voltage micro sources especially for photovoltaic (PV) and fuel cell sources. This novel high voltage Non-isolated Boost DC-DC converter topology is best replacement, where high voltage conversion ratio is required without the transformer and also need continuous input current. Since the proposed topology utilizes the stack-based structure, the voltage gain, and the efficiency are higher than other conventional non-isolated converters. Switches in this topology is easier to control since its control signal is grounding reference. Also, there is no need of extra gate driver and extra power supply for driver circuit, which reduces the cost and size of system. In order to show the feasibility and practicality of the proposed topology principle operation, steady state analysis and simulation result is presented and analyzed in detail. To verify the performance of proposed converter and theoretical analysis 360W laboratory prototype is implemented.

• Journal of Broadcast Engineering
• /
• v.19 no.2
• /
• pp.250-256
• /
• 2014

Non-reference P frame coding is used to enhance coding efficiency in low-delay encoding configuration of Internet Video Coding (IVC), which is being standardized as a royalty-free video codec in MPEG. The existing method of non-reference P frame coding which was adopted in the reference Test Model of IVC (ITM) 4.0 adaptively applies a non-reference P frame with a fixed coding structure based on the magnitude of motion vectors (MVs), however, which unexpectedly degrades the coding efficiency for some sequences. In this paper, the existing non-reference P frame coding is improved by changing non-reference P frame coding structure and applying a new adaptive method using the ratio of the amount of generated bits of non-reference frames to that of reference frames as well as MVs. Experimental results show that the proposed non-reference P frame coding gives 6.6% BD-rate bit saving in average over ITM 7.0.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.28 no.6
• /
• pp.1-15
• /
• 2001

The purpose of this study is to figure out the structural characteristics of urban plant community and suggest restoration model of Quercus mongolica in the case of Korean national Capital Region. The investigation areas were selected from urban area of Mt. Nam at Chung-Gu, suburban areas of Mt. Bong at Eunpyoung-GU, Mt. Sungju at Buchon City and non-urban areas of Mt. Suri at Kunpu City and Mt. Chonma t namyangju-City. After the main study field had been classified into the evaluation of the ecological characteristics and the modeling of the vegetation. We analyzed to evaluate the ecological characteristics of the forest structure -- successional stage, naturalness, multi-layer structure of the forest and species diversity, and the plant community structures. We have proposed vegetation restoration model based on the selection of proper plants, the number of individuals, diameter short area of breast height, the shortest distance between plants in non-urban area. As for successional stage, It was judged that the ecological succession may not be followed like the present stage of the surveyed areas in urban, suburban and non-ruban areas. As for the retention of naturalness and multi-layer structures of vegetation, In Quercus mongolica community, Robinia pseudo-acacia and Ailanthus altissima occurred in each layers at Mt. Nam, Mt. Bong and Mt. Sungju, and Eupatorium rugosum occurred in herbaceous layer at Mt. Nam. Consequently, the ecological restoration plan following the structure of the vegetation in Mt. Chonma seemed to be advisable in Q. mongolica community, there were less number of species and individuals in urban areas than those of non-urban areas. Planting of trees following the simulated native plant community of non-urban areas seemed to be required to promote the plants in urban areas. Considering the number of individuals up to three layers in each 400$m^2$ area, it was composed of twenty nine in canopy layer, forth nine in understory layer, 367 in shrub layer and 33.7% herbaceous ground cover in the Q.mongolica community. The suggested restoration model in this study is nan applicable model for the introduction in the cities, and this study shows that continuous experiments and field investigation on this model should be performed in the future.

• The Journal of the Korea Contents Association
• /
• v.16 no.3
• /
• pp.247-256
• /
• 2016

This paper points out that the existing digital story creation tools are biased in the field of entertainment storytelling, so it proposes a specialized tool for non-fiction creation. This paper selects Quantifying Theory to design this tool. When creating nonfiction storyline, it is important to have the appropriate combination between the actual events and fictional elements. A Gossip System, based on Quantifying Theory, is suitable for that work. Before designing a Gossip System as a nonfiction creation tool, this analysis evaluated that the Gossip System in and . As a result, the linked structure in is useful in searching for material for non-fiction creation, and the separated structure in is ideal for arranging dramatic events. This paper proposed a method of switching the fact to fiction through a combination of this two Gossip System structure. I conclude that this is the best method for non-fiction creation tool.

• Journal of Surface Science and Engineering
• /
• v.37 no.5
• /
• pp.249-252
• /
• 2004

Effects of HA and TiN coating on the electrochemical characteristics of Ti-6AI-4V alloys for bone plates were investigated using various test methods. Ti-6AI-4V alloys were fabricated by using a vacuum induction furnace and bone plates were made by laser cutting and polishing. HA was made of extracted tooth sintered and then tooth ash was used as HA coating target. The TiN and HA film coating on the surface were carried on using electron-beam physical vapor deposition (EB-PVD) method. The corrosion behaviors of the samples were examined through potentiodynamic method in 0.9% NaCI solutions at $36.5\pm$$1^{\circ}C$ and corrosion surface was observed using SEM and XPS. The surface roughness of TiN coated bone plates was lower than that of tooth ash coated plates. The structure of TiN coated layer showed the columnar structure and tooth ash coated layer showed equiaxed and anisotrophic structure. The corrosion potential of the TiN coated specimen is comparatively high. The active current density of TiN and tooth ash coated alloy showed the range of about $1.0xl0^{-5}$ $A\textrm{cm}^2$, whereas that of the non-coated alloy was$ 1.0xl0^{-4}$ $A\textrm{cm}^2$. The active current densities of HA and TiN coated bone plates were smaller than that of non-coated bone plates in 0.9% NaCl solution. The pitting potential of TiN and HA coated alloy is more drastically increased than that of the non-coated alloy. The pit number and pit size of TiN and HA coated alloy decreased in compared with those of non-coated alloy. For the coated samples, corrosion resistance increased in the order of TiN coated, tooth ash coated, and non-coated alloy.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.195-200
• /
• 2003

A two-dimensional "twin-jet counterflow" burner has been designed for the better understanding of the stability of turbulent flames. This flow system enables one to systematically investigate various effects on non-premixed flames, including the effects of curvature, negative strain, and non-premixed flame interactions. The objective of this study is comparing characteristics of extinction of non-premixed methane flames with that of non-premixed propane flames investigated previously. The extinction limit of non-premixed methane and propane flames can be extended compare to that for the conventional counterflow non-premixed flame because of the existence of petal shaped flame and have same structure. The hysteresis in transition between the petal shaped flame and the curved two-wing flames could be observed. We could find differences between non-premixed methane flame and non-premixe propane flame such as the position of one wing extinction and the regime of one wing extinction.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.4
• /
• pp.467-474
• /
• 2004

A numerical method and algorithms is proposed to perform optimization of non-linear response structures. An analytical and numerical method based finite element method is also proposed for the transformation of non-linear response into linear response. Loads transformed from this method are defined as the equivalent linear loads. With the loads and the transformed response, linear static optimization is performed for nonlinear response structure with geometric and/or material non-linearity. The results of the optimization are compared with them of typical non-linear response optimization using finite difference method. The proposed method is very efficient and derives good solution.

• Applied Microscopy
• /
• v.45 no.1
• /
• pp.32-36
• /
• 2015

The microstructural features of FeCoCrNi, FeCoCrNiAl and FeCoCrNiSix (x=0, 5, 10, 15, 20) alloys have been investigated in the present study. The microstructure of FeCoCrNi alloy changes dramatically with equiatomic addition of Al. The fcc irregular shaped grain structure in the as-cast FeCoCrNi alloy changes into the bcc interconnected structure with phase separation of Al-Ni rich and Cr-Fe rich phases in the as-cast FeCoCrNiAl alloy. The microstructure of FeCoCrNi alloy changes with the addition of Si. With increasing the amount of Si, the fcc structure of the grains is maintained, but new phase containing higher amount of Si forms at the grain boundary. As the amount of Si increases, the fraction the Si-rich grain boundary phase increases.

• Journal of Korean Association for Spatial Structures
• /
• v.20 no.2
• /
• pp.87-94
• /
• 2020

The present study is aimed to calculate the optimal damping according to the seismic load on the structure with a non-seismic design to perform structure analysis considering the deformation of structural joint connection and panel zone; to develop design program equipped with structural stability of the steel frame structures reinforced with the panel zone and viscous dampers, using the results of the analysis, in order to systematically integrate the seismic reinforcement of the non-seismic structures and the analysis and design of steel frame structures. The study results are as follows: When considering the deformation of the panel zone, the deformation has been reduced up to thickness of the panel double plate below twice the flange thickness, which indicates the effect of the double plate thickness on the panel zone, but the deformation showed uniform convergence when the ration is more than twice. The SMRPF system that was applied to this study determines the damping force and displacement by considering the panel zone to the joint connection and calculating the shear each floor for the seismic load at the same time. The result indicates that the competence of the damper is predictable that can secure seismic performance for the structures with non-seismic design without changing the cross-section of the members.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.10
• /
• pp.1558-1565
• /
• 2004

It is important to determine supporting locations for structural stability when a structure is loaded with non-uniform load or supporting locations as well as the number of the supporting structures are restricted by the problem of space. Moreover, the supporting location optimization of complex structure in real world is frequently faced with discontinuous design space. Therefore, the traditional optimization methods based on derivative are not suitable Whereas, Genetic Algorithm (CA) based on stochastic search technique is a very robust and general method. The KSTAR in-vessel control coil installed in vacuum vessel is loaded with non- uniform electro-magnetic load and supporting locations are restricted by the problem of space. This paper shows the supporting location optimization for structural stability of the in-vessel control coil. Optimization has been performed by means of a developed program. It consists of a Finite Element Analysis interfaced with a Genetic Algorithm. In addition, this paper presents an algorithm to find an optimum solution in discontinuous space using continuous design variables.