• Journal of The Korean Society For Urban Railway
• /
• v.6 no.4
• /
• pp.383-392
• /
• 2018

This study investigated the change of additional axial stress of rail and reaction force at bridge bearings due to the track-bridge interaction when laying CWR on non-ballasted railway bridges including truss bridges with relatively long span. According to the results of the present study, additional axial stresses of rail and reaction forces at bridge bearings showed a large increase when CWR is installed on the non-ballasted railway bridge. The additional axial stress of rail can be acceptable if sufficient lateral resistance can be obtained. However, if the reaction force increases, there is a risk of damage of the bearing or pier, and therefore, it is necessary to take measures to mitigate the reaction force. It is found that additional axial stress of rail decreases when considering the frictional resistance of the bridge movable support, but its effect on the bearing reaction force is very small. On the other hand, when the longitudinal track restraint decreases, both additional axial stress of rail and bearing reaction force are reduced to a large extent. Also, when the ZLR fastening devices are applied to the region where the additional axial stress of rail is highest, bearing reaction force as well as additional axial stress of rail greatly decreased. Therefore, the application of ZLR fastening devices with the reduction of the longitudinal track restraints is very effective for installing CWR on non-ballasted railway bridges.

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.534-539
• /
• 2001

This paper presents the critical speed analysis of geogrid-reinforced rail roadbeds on soft soil. A rail roadbed on soft ground must be designed to avoid intolerable stress in the underlying soil and to give sufficient support for the rail system. At high speeds, the deformation of rail systems will gain dynamic amplification, and reach excessive values as a certain speed, here termed critical speed is approached. The elastic Winkler foundation model was used to predict the critical speed of geogrid-reinforced rail roadbeds on soft soil and the model properties were determined by the in-situ cyclic plate load test. Based on the parametric study of elastic beam on Winkler foundation model, the critical speed increase with the increase of the flexural risidity of subgrade EI and the stiffness coefficient of Winkler foundation k. From the in-situ cyclic load tests and analysis of elastic beam on Winkler foundation model, the critical speed increase with increase in number of reinforced layer and non-dimensional value for depth of first geogrid layers and the thickness of reinforced rail roadbed u/d.

• Proceedings of the KOR-KST Conference
• /
• 1996.06a
• /
• pp.131-137
• /
• 1996

This paper discusses the necessity, strategy and objectives of the rail transportation recently developed in Shanghai. The objective should not be regarded just as a term project, but should be taken as an urgent mission with the 21st century, Shanghai should possess a network of about 100km of rail transport lines. To this end, the following measures are suggested : grade separation of all lines on elevated structures ; developing the rail car industries ; full utilization of all available transportation facilities ; optimizing the use of the space resources of highways ; bringing into play the initiatives of all parties concerned. Recently, it has become a popular consensus that the development of high-speed, safe, punctual, comfortable, non-pollution rail transport with large capacity is the best and only solution to Shanghai urban transportation. In this respect, this dissertation deals with the development strategy for current Shanghai rail construction, together with the infractructure in Shanghai, positioning the developing target; meanwhile, some proposals and solutions to hit this target will be put forward for the reference of leaders and experts.

• Structural Engineering and Mechanics
• /
• v.2 no.1
• /
• pp.95-112
• /
• 1994

This paper describes the formulation and application of a dynamic model for a conventional rail track subjected to arbitary loading functions that simulate wheel/rail impact forces. The rail track is idealized as a periodic elastically coupled beam system resting on a Winkler foundation. Modal parameters of the track structure are first obtained from the natural vibration characteristics of the beam system, which is discretized into a periodic assembly of a specially-constructed track element and a single beam element characterized by their exact dynamic stiffness matrices. An equivalent frequency-dependent spring coefficient representing the resilient, flexural and inertial characteristics of the rail support components is introduced to reduce the degrees of freedom of the track element. The forced vibration equations of motion of the track subjected to a series of loading functions are then formulated by using beam bending theories and are reduced to second order ordinary differential equations through the use of mode summation with non-proportional modal damping. Numerical examples for the dynamic responses of a typical track are presented, and the solutions resulting from different rail/tie beam theories are compared.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.505-515
• /
• 2009

In railway bridges, various loads including train load, transverse load and braking force are applied to continuous CWR or semi-continuous longer rail located on non-continuous bridge superstructures. The rail-girder interaction due to thermal expansion is also very complex in railway bridges because the thermal characteristics for each of the rails and girder are quite different. Recently, the bridge retrofits for seismic loads were performed on bridges not designed for these loads. These retrofits may however have limitations with respect to rail-girder interactions because, in general these retrofits address issues related only to seismic loads. In this study of seismic evaluations for railway bridges, the load effects on the bridge rails from the road beds through the continuous rails shall be considered. Practical methods will be proposed which will increase the railway stability. For this, rail-girder interaction analyses due to train loads, temperature changes and seismic loads were performed and the results reviewed from a practical point of view.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.679-685
• /
• 2003

Rotem has been using VAMPIRE for simulation and verification of the railway vehicle design. To improve the capability and accuracy of the analysis ability, ADAMS/Rail has been chosen as the next generation analysis tool. The dynamic performance of the railway vehicle, which is designed and manufactured by Rotem, is analyzed and simulated using ADAMS/Rail. The critical speed for linear and non-linear stability on tangent track, curving performance on various curved tractk, ride quality, derailment coefficient and the eigen values are calculated. In this paper, the results from ABAMS/Rail are compared with VAMPIRE's results.

• Journal of Korean Society of Transportation
• /
• v.27 no.5
• /
• pp.155-162
• /
• 2009

The recent increase of light rail construction by the private sector in Korea has caused a new issue in forecasting rail demand. Integrated fare systems between several rail operators is convenient and brings cost savings to users, and therefore is also very effective in increasing demand. However, it causes some short-term revenue loss to operators so that the private sector often suggests a non-integrated fare system. The current rail demand forecasting model is based upon an integrated fare system. Thus this model cannot be used to forecast the demand with a non-integrated fare system. Some value of transfer fare should be estimated and applied to forecast the demand in a non-integrated fare system. This study conducted a stated preference (SP) survey on urban railway passengers and estimated the value of transfer fare. The estimated value is 2,609 Won/hr, which is about 52% of in-vehicle time. This shows railway users have a tendency to pay more for transfer fares to save time or distance. This value has some limitations since it is derived from the SP survey. If some non-integrated fare system is applied in the future and a RP survey is conducted and compared with these study results, a more clear value of the transfer fare will be derived.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.4
• /
• pp.398-413
• /
• 2011

For railway safety, it is very important to detect damages of rails at their early stage because any undetected damage in a rail can break the rail and cause a serious railway accident. In this paper, several NDT applicable to rail inspections are described. Major damage types in rails are discussed first and the rail inspection technology using conventional piezoelectric ultrasonic transducers, which is widely adopted for damage detection of rails, is explained. Other NDT being researched or tested for rail inspection are also discussed as complementary technologies to the concurrent contact type ultrasonic inspection. Characteristics of each rail inspection technologies are evaluated in order to provide requirements for future development of a new rail inspection method.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.91-98
• /
• 2009

For maintaining railroad, accumulated passing tonnage is a determinant factor of appropriate rail replacement time. Recently, Seoul Metro's rail maintaining system and technology is being improved from previous years, which increasing a standard of rail replacement. Thus, this brings importance of estimating and managing for accumulated passing tonnage. In case of light weighted train such as subway, current method of calculating accumulated passing tonnage has defaults of misrepresenting accumulated passing tonnage data. Because current method is based on the weight of passengers and train., and operation data. In addition, currently there is no mechanical and electronic system that could represent and support the accurate data between heavy and non-heavy traffic area, and accumulated passing tonnage is calculated inaccurately by estimating average value each line. The current method of calculating accumulated passing tonnage misleads to unpredictable data that represent inappropriate rail replacement period, which leads to under or over analyzed replacement period. If accumulated passing tonnage is over estimated, rail replacement leads to waste of budget. Hence, it is necessary to construct reliable actual measurement system to manage rail's life safely and efficiently, and in this study the accumulated passing tonnage measurement device is installed with using rail pad of optical fiber sensors and its effect is analyzed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.7
• /
• pp.1303-1310
• /
• 2016

The track circuit carries out a train detection using a electrical closed loop, and incidentally it detects the rail rupture using the track circuit current flowing rail. However, in the case of the axle counter or the Radio based train control system, it requires a new way for detecting the rail rupture because of not using the track circuit. To solve this problem, it periodically checks non-steady state of rail by the track inspection car. but real-time detection of the rail rupture is impossible. Therefore, this paper analyzed feasibility to realize a real-time detection of rail rupture by using the return current.