• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.27-30
• /
• 2007

Recently, use of light-weight panel is increasing in building. Styrofoam sandwich panel is inexpensive and it is excellent in insulation ability and constructability. But styrofoam of panel inside is low ignition point. Consequently, when panel is fired, it is occur in poisonous gas. On the other hand, light-weight foamed concrete is excellent in insulation ability, fire resistance due to inner pore. Properties of light-weight concrete is influenced by foaming agent type. Accordingly, this study investigate in insulation property of according to foaming agent type in order to using light-weight foamed concrete instead of styrofoam. As a results, Non-heating zone temperature of light-weight foamed concrete of using AP, FP are lower than light-weight foamed concrete of using AES. Light-weight foamed concrete of using AES, FP are satisfied with fire performance of two hours at foam ratio 50, 100. Light-weight foamed concrete of using AP is satisfied with fire performance of two hours at AP ratio 0.1, 0.15. Insulation property is better closed pore by made AP, FP than open pore by made AES.

• 한국전기화학회:학술대회논문집
• /
• 2001.11a
• /
• pp.145-161
• /
• 2001

Novel characterization of thermal properties of a battery has been introduced by defining its frequency-dependent thermal impedance function. Thermal impedance function can be approximated as a thermal impedance spectrum by analyzing experimental temperature transient which is related to the thermal impedance function through Laplace transformation. In order to obtain temperature transient, a process has been devised to generate external heat pulse with heating wire and to measure the response of battery. This process is used to study several commercial Li-ion batteries of cylindrical type. The thermal impedance measurements have been performed using potentionstat/galvanostate controlled digital signal processor, which is more commonly available than flow-meter usually applied for thermal property measurements. Thermal impedance spectra obtained for batteries produced by different manufactures are found to differ considerably. Comparison of spectra at different states of charge indicates independence of thermal impedance on charging state of battery. It is shown that thermal impedance spectrum can be used to obtain simultaneously thermal capacity and thermal conductivity of battery by non-linear complex least-square fit of the spectrum to thermal impedance model. Obtained data is used to simulate a response of the battery to internal heating during discharge. It is found that temperature inside the battery is by one-third larger that on its surface. This observation has to be considered to prevent damage by overheating.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.10
• /
• pp.44-51
• /
• 2020

We studied the heating characteristics of a whirling spindle. This spindle is an important component of a whirling machine for turning a ball screw shaft. In the manufacturing process for a conventional ball screw shaft, a single tool is used to form a spiral in a lathe machine tool. Thereafter, a high-frequency heat treatment process is performed. Recently, a whirling-type cutting method has emerged. This method can perform hard turning in the rotating direction of the spiral portion of the ball screw shaft by rotating and mounting multiple tools. The whirling method can be applied to the heat-treated material. In this study, an experimental apparatus was constructed to analyze the whirling spindle. The experiment proceeded in four steps. The rotating speed of the whirling spindle was set to ISO random and sequential rising conditions. Cooling and non-cooling modes in the cooling jacket were tested. As a result of the above experiment, the heating characteristics of the whirling spindle were derived.

• Korean journal of food and cookery science
• /
• v.27 no.6
• /
• pp.745-754
• /
• 2011

To improve the textural properties of gluten free rice flour based products, the physicochemical and pasting properties of extruded non-waxy rice flours using extruder were investigated. The high yielding Tongil type rice variety, Hanarum was used. Hanarum rice flour was prepared by dry milling from soaked and dried rice grain. The operation conditions of twin screw extruder were 250 rpm of screw speed, $160^{\circ}C$ of barrel temperature, and 24, 27, and 30% of moisture content. Hanarum extruded rice flour (HERF) were lower in crude lipid and ash contents, but higher in crude protein than Hanarum rice flour (HRF). The color values of HERF showed significantly different (p<0.05) with different moisture contents. Water binding capacities, apparent amylose contents, and damaged starch of HERF were higher than those of HRF. Moisture contents affected water binding capacities of HERF. Solubility increased with increasing heating temperature and solubilities of HERF differed significantly (p<0.05). X-ray crystallinity was changed after extrusion cooking and that of HERF showed sharp peaks at $2{\theta}=18-20^{\circ}$. The pasting viscosities of HERF kept lower values (~ 10 RVU) constantly.

• Journal of the Korean housing association
• /
• v.20 no.5
• /
• pp.123-132
• /
• 2009

As society increasingly ages, maintaining an independent lifestyle at home becomes an important issue for older people. This study aims to determine old people's housing needs for maintaining an independent lifestyle despite their health status and living arrangements. A total of 438 residents voluntarily took part in a research questionnaire survey through the quota sampling method. The participants were grouped according to age (60-64, 65-69, 70-74, and over 75), gender (male and female), and house type (apartment houses and others). The results are as follows. (1) The senior residents are mostly within a non occupational, low income, and low subjective living status. (2) They are satisfied with their current residence and hope to manage the rest of their life in the same place. (3) Three out of five residents prefer the apartment housing type to other types of housing. The preferred dwelling size, number of rooms, and preference for use of an extra room all varied depending on gender and housing type as well as whether they were a couple or living alone. (4) The older residents have a higher need for a safety system than do the younger residents. Female residents pay more attention to convenience while male residents pay more attention to safety. The non-apartment residents require more modification to fundamental facilities such as a heating and ventilation system, wind protection, and additional storage than do the apartment residents. This study has thoroughly analyzed request characteristics according to basic qualities of the elderly households.

• Journal of Energy Engineering
• /
• v.22 no.2
• /
• pp.211-225
• /
• 2013

To run an optimal operation of Integrated energy supply facilities, we need to analyze heat consumption patterns of District heating users and derive optimum and maximum load ratio of heat production facilities unit. This study selects three District heat production facilities. It also classifies District heating users into residential apartment buildings and eight non-residential buildings and analyzes heat consumption results for an year. Finally it carries out the analysis of how the ratio change of each type affects maximum load ratio, facility utilization ratio, heat supply range. According to this study, three different District heat facilities of residential apartment building show similar daily and annual heat consumption patterns. Annual average load ratio, maximum load ratio and annual heat demand increase as outdoor temperatures decrease. Non-residential buildings in urban District focused on apartment buildings display similar by the daily and annual heat consumption patterns. Yet their daily and annual maximum load ratio differ according to outdoor temperature, District, building types and their composition ratio. In the case of urban District focused on apartment buildings reach optimum and maximum load ratio when apartment buildings reaches 60-70% of the total. At that point heat supply range becomes maximized and the most economic efficiency is obtained.

• Solar Energy
• /
• v.17 no.1
• /
• pp.3-15
• /
• 1997

The goal of this paper is to measure and compare the performance of solar heat pump for school classroom heating. To accomplish the goal, solar heat pump with alumium roll bond type evaporator and indoor heat exchanger(condenser) was built and fully instrumented with thermocouples and pressure transducers etc. The test results showed that the COP and capacity of R-134a($CF_3CH_2F$) were higher than those of R-12($CF_2Cl_2$). The solar heat pump system for room heating was designed to show the best efficiency that the room temperature make $18{\sim}20^{\circ}C\;and\;23{\sim}25^{\circ}C$ in Seoul during November, December, and January.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.2
• /
• pp.157-164
• /
• 2016

In this research, based on the condition of using desulfurization gypsum(FGD) as a stimulator for high-volume blast furnace slag cement mortar, sieving and heating process methods of removing activated carbon in FGD were compared with the non-processed FGD and recycled and natural fine aggregates were compared for suitable aggregate to be used. According to the result of experiment, sieving with 0.3mm was more efficient than $500^{\circ}C$ heating for processing the FGD, and recycled fine aggregate showed more favorable result than natural fine aggregate at the FGD content was 5 to 10%. On the other hand, the mortar mixture including recycled fine aggregate had a high drying shrinkage, and absorption ratio, and thus specific limitations on applying recycled fine aggregate should be required.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.11 no.2
• /
• pp.12-18
• /
• 2015

The energy pile, used for both structural foundations and heat exchangers, brings about heat exchange with the ground formation by circulating a working fluid for heating and cooling buildings. As heat exchange occurs in the energy pile, thermal stress and strain is generated in the pile body and surrounding ground formation. In order to investigate the thermo-mechanical behavior of an energy pile, a comprehensive experimental program was conducted, monitoring the thermal stress of a cast-in place energy pile equipped with five pairs of U-type heat exchanger pipes. The heating and cooling simulation both continued for 30 days. The thermal strain in the longitudinal direction of the energy pile was monitored for a 15 operation days and another 15 days monitoring followed, without the application of heat exchange. In addition, a finite element model was developed to simulate the thermo-mechanical behavior of the energy pile. A non-linear contact model was adopted to interpret the interaction at the pile-soil interface, and thermal-induced structure mechanics was considered to handle the thermo-mechanical coupled multi-field problem.

• Fashion & Textile Research Journal
• /
• v.3 no.5
• /
• pp.466-472
• /
• 2001

To find a suitable condition in this process examined, we investigated the main control factors, such as, the NaOH concentrations, such as, the NaOH concentrations, the heat treating times, and the heating temperatures. The resulting mechanical properties of the fabrics also studied. The samples used were Nylon/Co-PET sea-island type composite microfiber (Co-PET content: 35%) non-woven fabric. The conclusions obtained were as follows. 1. For the complete extraction of Co-PET from the sample non-woven fabric in the dry hot air process, $160^{\circ}C$ of air temperature, 15 min. of treatment time, and around 30% of NaOH concentration were required. On the other hand, in the wet hot air process, $140^{\circ}C$ of air temperature, 3.5 min. of treatment time, and around 30% of NaOH concentration were required. 2. The mechanical properties of the continuous processed samples showed that the WT, B, and WC increased with increasing the weight reduction ratio. However, the G, decreased with increasing the weight loss ratio. Note that, particularly in B, it increased drastically when the weight deduction ratios exceeded 30%. 3. As increasing the wet hot air temperature from 130 to $140^{\circ}C$, B appeared to increase, however, WT, G, and WC appeared to decrease. 4. The best condition found in this continuous process to extract Co-PET is the wet hot air temperature of 140, NaOH concentration of 28% or above, and the treatment time 2-4 min.