• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.391-395
• /
• 1997

The transmission of sound and vibration through structures is of interest in many noise control problems, including architectural acoustics, sound transmission through air craft, spacecraft and ship, and the transmission of noise through machinery and engine enclosures. Statistical Energy Analysis provides a simple and accurate method of approaching these problems. In this paper, comparing the measured coupling loss factor of plate-beam with measured coupling loss factor of mass on the junction will be inspected.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국제학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.550-553
• /
• 1993

Methods of Alternating Noise Canceling were previously developed for the optical instrumentation;one using a dual photo sensor and another using a single photo sensor that could cancel normal mode noise on a transmission line, even if the noise was of equal status noise. But the methods could not remove noise on sensor line. This paper discusses a new method of using a photo sensor with a resistance sensordummy, effectively canceling equal status normal mode noise not only on a sensor line but also on a transmission line of an optical instrumentation. The accuracy of this method has been verified by experiments using sinusoidal wave as an equal status noise on a sensor line and/or rectangular wave as an equal status wide band noise on a transmission line respectively.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.628-632
• /
• 2001

Experimental approach was investigated to improve gear rattle noise of a small car. During the development of a small car serious problem occurred inside the transmission gear units. The transmission was a carried over system from a less powered predecessor. Several components of suspicion were investigated, and applied to reduce rattle noise. In general, backlash, the assembly gaps, and the clutch disk rattle induce gear rattle noise. Above mentioned improvements were applied to reduce the noise, but still problem remained. Meanwhile, the temperature inside the gearbox was reported to be unusually high and the life of transmission oil quality deteriorated drastically, Temperature increment caused the large gap between the bearing outer diameter and the transmission housing. Large gap made the gear shaft assembly move intermittently and impact each other. The tighter control of the assembly gap allowed the rotating shafts smoothly and reduced the gear rattle noise even in the high temperature range.

• 한국음향학회지
• /
• 제40권6호
• /
• pp.607-614
• /
• 2021

승강기 소음에 대한 연구는 주로 발생 원인 및 저감 방안에 대한 것이 많았다. 승강기 소음을 정확하게 측정하고 평가하는 방법에 대해서는 아직 연구가 미비하다. 측정방법에 대해서는 국제표준으로 제정하여 측정 방법이 있지만 그것 또한 고층아파트에 적용하기 힘들고, 승강기 소음의 특성을 면밀히 반영하지 않은 것이 많다. 이러한 문제를 해결하고자 현행 규격에서 승강기 소음 측정 방법을 개선하는 연구가 이루어 졌다. 본 연구에서는 승강기 소음의 특성을 면밀히 파악하고자 하였다. 승강기 소음과 다른 설비기기와의 주파수 분석을 통해 승강기 소음이 다른 설비기기와는 다른 특성의 소음임을 검증 하였다. 승강기 소음은 구조전달소음으로 대표적인 구조전달소음인 중량바닥충격음과 비교 분석을 하였다. 승강기 소음과 중량바닥충격음과의 상관성은 0.9 수준으로 매우 높게 나타났다. 이 결과로 승강기 소음은 중 저주파대역이 주요한 구조전달소음이며 다른 설비기기와 함께 평가될 수 없음을 검증 하였다.

• 소음진동
• /
• 제11권3호
• /
• pp.401-409
• /
• 2001

Passive type mufflers installed on every car haute inherent problem of lowering engine power and fuel efficiency caused by backpressure which is byproduct of complex internal structure. Recent improvements like installing a calve to change exhaust gas path depending on power requirement and rpm have only marginally improved performance. Tremendous amount of recent research works on active exhaust noise control have failed to commercialize because of numerous physical and economical reasons. In this paper, a unique seal-active muffler using difference of transmission paths is presented. In this system exhaust pipe is divided into two and joined again downstream. Exhaust noise is reduced by destructive interference when two-divided noise join again with transmission paths'difference which is half of the wavelength of a main noise frequency. One divided path has a sliding mechanism to change length thereby transmission path length difference is adjusted to entwine rpm change. The proposed system has minimal backpressure and does not need a secondary sound source like a speaker so it can overcome many problems of failed active noise control methods. We have verified proposed system's superior performance by simulation and comparison experiment with passive mufflers.

• 대한전기학회논문지:전력기술부문A
• /
• 제51권1호
• /
• pp.23-28
• /
• 2002

In order to survey the radiation characteristics of pure line noise of unwanted noise from overhead high voltage AC transmission lines, a disk type gap noise generator was manufactured. Disk size which decides capacitance between the noise generator and earth was selected through preliminary indoor experiments and analysis by using surface charge method. The capacitance is one of principal parameters related to the injection of a proper noise current into lines. On the basis of the capacitance obtained from calculation, 5mm of space was given to the gap of the noise generator to be installed o test line and an aluminum disk of 60cm radius was made. The field experiments were performed with the noise generator hung on the Kochang 765 kV full scale test line. As the results, the useful data which can be used to analysis the radiation characteristics of noise from transmission lines were obtained. Those are the directivity of antenna toward the line, lateral profiles, frequency spectra, height pattern and so on.

• Journal of Mechanical Science and Technology
• /
• 제18권11호
• /
• pp.1909-1915
• /
• 2004

The hermetic rotary compressor is one of the most important components of an air conditioning system since it has a great effect on both the performance and the noise and vibration of the system. Noise and vibration occurs due to gas pulsation during the compression process and to unbalanced dynamic force. In order to reduce noise and vibration, it is necessary to identify their sources and transmission path and effectively control them. Many approaches have been tried in order to identify the noise transmission path of a compressor. However, identification has proven to be difficult since the characteristics of compressor noise are complicated due to the interaction of the compressor parts and gas pulsation. In this study, the statistical energy analysis has been used to trace the energy flow in the compressor and to identify the transmission paths from the noise source to the exterior sound field.

• 한국생산제조학회지
• /
• 제9권6호
• /
• pp.9-18
• /
• 2000

This study includes noise automatic inspection system for washing machine auto-transmission one of modern home necessary. We effort to find and certificate sound noise source by sound power and sound intensity, and apply to frequency analysis in vibration related sound noise. still more we have been studying to data acquisition and programming for MS VisualBasic version 5.0. System component is below. 1) Pentium PC or data acquisition. 2) DSO for noise acquisition. 3)S/W for comparison and decision. 4) I/F Board for data communication. Wave form data through the DSO are converting to ASCII code data. The ASCII code through binary converting S/W. Finally we will making noise monitoring system and automatic inspection system.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 창립기념 춘계학술대회 논문집
• /
• pp.249-256
• /
• 1998

Design target values of transmission loss in a high-speed train wall are suggested by calculating the difference between interior and exterior noise levels of it. Exterior noise level distribution on the boundary of train wall is calculated by Sysnoise, with sound source input prepared by experiments. Two kinds of exterior sound sources are considered, the rolling noise of train wheels on the rail and the aerodynamic noise from the pantograph. Interior noise level is provided by high-speed design target. Transmission loss characteristics according to the frequency band are examined.

• 한국전자파학회지:전자파기술
• /
• 제4권3호
• /
• pp.18-29
• /
• 1993

장거리 초고속 단일모드 광파이버 전송 시스템에서, 색분산은 복조된 파형의 찌그러짐을 생기게 하며, 그 결과 수신된 신호 간 간섭을 일으켜 전송 시스템의 성능을 저하시킨다. 본 논문에서는 강도변조-직접검파 시스 댐의 색분산제한을위상변조에서 진폭변조로의 전환잡음의 영향을고려함으로서 연구하였다. 파이버 색분산에 의한 위상-진폭으로의 전환잡음을 잡음전력 스펙트럼 밀도를 유도함으로서 분석하였으며 위상-진폭 전환잡음을 피하기 위한 시스댐 전력손실과 레이저 선폭에 대한 요구조건을 수치해석을 통하여 구하였다.