• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.328-329
• /
• 2009

Air-Damping Mount is proposed to compromise between performance and weight & cost. The design of Air-Damping Mount was based on the specification from the engine mounting system analysis of a small car. To verify it's feasibility, R&H test was done on the small car and it is proven that Air-Damping Mount shows the performance between hydraulic mount and rubber mount.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.950-955
• /
• 2002

ISO 140-11 specifies a method for measuring the acoustic properties of floor coverings from the view-point of reducing impact sound transmission. This test method is limited to the specification of procedures for the physical measurement of sound originating from an artificial impact source under laboratory conditions. In this study, ISO 140-11 was reviewed to applicable to domestic floor coverings installed on lightweight floors.

• Journal of the Korean Institute of Navigation
• /
• v.16 no.3
• /
• pp.65-76
• /
• 1992

An algorithm to determine the optimum nominal value of geometrical and material parameters in divice modelling is proposed. The algorithm uses the yield and variance prediction formula and Monte-Carlo analysis. The performance specification of the noise figure must also be satisfied. In this paper, the total number of considered devices is 1000, and each parameter of geometrical and material parameters is generated randomly within the limits of ${\pm}3%$ of nominal value, and the distribution of 1000 geometrical and material parameters is gaussing distribution.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.392.2-392
• /
• 2002

ISO 140-11 specifies a method for measuring the acoustic properties of floor coverings from the view-point of reducing impact sound transmission. This test method is limited to the specification of procedures for the Physical measurement of sound originating from an artificial impact source under laboratory conditions. In this study, ISO 140-11 was reviewed to applicable to domestic floor coverings installed on lightweight floors.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.6
• /
• pp.470-477
• /
• 2004

This study shows the design process of a MR damper for semi-active suspension systems. Damping force characteristics of the designed damper was predicted through the flow analysis and magnetic analysis. The predicted results were compared with the experimental results and the initial design specification was modified according to the results.

• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.209-210
• /
• 1998

Noise characteristics of preamplifier, the most essential part of on-chip signal processing circuitry for the active semiconductor neural probe, is the important factor determining the overall signal-to-noise-ratio (SNR). We present a systematic design method for the optimization of SNR, based on the spectral characteristics of the electrode, circuit noise and extracelluar action potential. Analytical expression is derived to calculate total output noise power. Output SNR of 2-stage CMOS preamplifier is tailored to meet the given specification while the layout area is minimized.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.481-487
• /
• 1997

The development of transportation and construction equipment has required higher engine power and lower operation cost. The sound which the engine emits often degrade the performance of the whole system which adopts that engine. Specially the marine engine requires high restriction on the noise level for the customer's comfort and safety. The noise and vibration of Diesel engine must be carefully considered in the early design step. The double antivibration system is effective to increase the efficiency of antivibration, and the acoustic enclosure for reducing the noise level. 2 DOF model was effective to estimate the antivibration performance, which allows to determine the mass of the engine bed and the specification of the engine mount. The mass distribution of the enclosure system can be considered effectively by using the FEM model. The design contains structurally rigid engine bed by FEM, which is for reducing the influence of the flexible vibration, rubber mount selection as well as the acoustic enclosure design.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.6
• /
• pp.470-475
• /
• 2014

In the past, transmission error(T.E.) has been identified as one of the main sources of gear whine noise, which cause serious passengers irritation at high frequency. In this study, to identify the correlation of the T.E. and gear whine noise, a T.E. measuring system was developed. By comparing the T.E. and gear whine noise level, T.E. target value which can represent the gear noise was proposed. The conclusions are followed: (I) It is possible to measure T.E. of the gear pairs (II) Similar trends are observed between T.E. and gear whine noise. (III) By observing the T.E. pattern, presence of sideband noise can be predicted. (IV) Proposed T.E. target value can be adopted to the gear manufacturing for gear noise quality management.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.951-956
• /
• 2008

Development of a silencer to Reduce Noise of Cross Talking in Apartment & Stores and air conditioning to fan Composite silencer application a specific of resonant type and expansion type, design possibility at reduction frequency. This silencer test result develop reduce 20dB of specification frequency. Pressure loss 2mmAq. This silencer is special of brief structure and possibility disjoint and joint, simple installation and maintenance.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.3 no.2
• /
• pp.93-100
• /
• 2008

In this paper, Low Noise Block down converter(LNB) is designed for a Ka-band satellite television receiver only(TVRO) using commercially available MMIC. Designed Low Noise Block down-converter is composed of three stage amplifiers involving input noise matched at first amplification stage, image reject band pass filter, frequency mixer and intermediate frequency amplification. Through LNB Module power budget to obtain gain and attenuation, Optimum LNB devices satisfying Ka-band LNB technical specification are selected. Experimental results of designed Ka-band LNB yields conversion gain of over $58{\pm}1dB$, noise figure of less than 1.5dB and phase noise of -94.6dBc @10KHz.