• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.166-170
• /
• 2008

In this study, it proved that transfer path analysis is a proper technique to estimate the interior noise from comparing measured interior noise in case of 3 point supported engine mount system. And the simulation of the vibration isolation for active engine mount using FXLMS algorithm is performed. Also, it verified that reduction of estimated interior noise from transfer path analysis and simulation of the vibration isolation.

• Journal of KSNVE
• /
• v.2 no.2
• /
• pp.107-116
• /
• 1992

An adaptive signal processing technique is implemented for the active noise cancellation of the plane acoustic wave propagating in a duct. To avoid the instability caused by the acoustic feedback from the control speaker to the detect microphone, an off-line modeling of the acoustic feedback plant is done using the FIR filter. Auxiliary path required for the filtered-x LMS algorithm is modeled as well. Before going into the experiments, a simulation is carried out under the same conditions with experiments. The simulation shows that the longer the length of the adaptive filter is, the better the results are achieved. Experiments have been carried out at lower audio frequency range (50 - 400Hz), and the results are in good agreements with those of simulation study. As a results of this adaptive noise control, around 50dB is reduced for a pure tone noise, and for a bandlimited noise with the bandwidth of 316Hz, a maximum of 30dB noise reduction is attained.

• Proceedings of the Safety Management and Science Conference
• /
• 2005.05a
• /
• pp.273-278
• /
• 2005

Prescribed according to the occupational safety and health low noise measurement method was changed to personal sampling in the method to measure an area noise. Such method had the limit which did not evaluated characteristic of sound of occurrence and the place of origin. This study was performed to establish an engineering remedy of the work-place noise. The subject was a vibration control process of the place of business in Pusan. A simulation program applied for an engineering improvement of the work-place noise. The results were as follows: 1. An noise occurrence level of the work-place before improvement was $88^{\sim}97dB(A)$, We applied an improvement method to be established and were expected to $80^{\sim}119dB(A)$. 2. The level of the noise-distribution to appear in the place of origin of the work-place before improvement was $90^{\sim}93dB(A)$ but, We executed the simulation after applied an engineering remedy and predicted $80^{\sim}85dB(A)$. A result of the simulation blue part was changed mostly into the dark blue color. The results suggest that simulation program establishes an engineering remedy and is useful to the case to apply.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.291-296
• /
• 2001

Recently, many methods are studied to analyze the noise of HDD and to reduce it. In this study, the simulation tool(SPATH) was developed to analyze a noise of HDD. The prediction technique of sound pressure level(SPL) of a given structural shape enables us to design a cover and a base with much less vibration and noise. In this paper, we measured the force of disk-spindle motor and predicted SPL from HDD by computational simulation. To get a SPL of HDD by computational simulation, modal analysis and forced vibration analysis were performed with ANSYS, and sound radiation was computed using SYSNOISE. The calculated results were compared with experimental results and a good agreement was obtained.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.11
• /
• pp.883-891
• /
• 2018

In this paper, aerodynamic noise simulation was conducted using DES (Detached Eddy Simulation) and FW-H (Ffowcs Williams and Hawkings) acoustic analogy for the tandem cylinders which have configuration similar to a landing gear of airplanes. Numerical simulation for the tandem cylinders whose centers are 3.7D apart was carried out and results were compared with the measured data such as flow characteristics, pressure coefficients on the cylinder surfaces and far-field noise characteristics. It was confirmed that periodically shedded vortices released at the upstream cylinder and impinged on the downstream cylinder surface are major sources of aerodynamic noise. After verifying the computational method of using DES and FW-H acoustic analogy for predicting aerodynamic noise of tandem cylinders, additional simulation was conducted to examine the effect of attaching a splitter plate at the rear of the upstream cylinder. It was confirmed that the noise level in specific frequency band decreased significantly because the splitter plate changed the vortex shedding features and reduced dipole noise source.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.12
• /
• pp.888-894
• /
• 2015

A new method for the simulation of the vehicle's interior road noise is proposed in the present study. The road noise model can synthesize road noise of a vehicle for varying driving speed within a range. In the proposed method, interior road noise is considered as a stochastic time-series, and is modeled by a nonstationary parametric model via two steps. First, each interior road noise signal, obtained from constant speed driving tests performed within a range of speed, is modeled as an autoregressive model whose parameters are estimated by using a standard method. Finally, the parameters obtained for different driving speeds are interpolated based on the varying driving speed to yield a time-varying autoregressive model. To model a full band road noise, audible frequency range is divided into an octave band using a wavelet filter bank, and the road noise in each octave band is modeled.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.7
• /
• pp.1511-1517
• /
• 2014

Based on the simulation model for phase noise effect, the phase noise performance of communication system using the M-ary APSK modulation method is analyzed in this paper. The phase noise effects for APSK higher order modulation method are modeled by considering the signal constellations of the modulation methods. The simulation model is verified by comparing the analytic results for lower order modulation signals with simulated results for those modulation signals. Based on the simulation model, then, the phase noise effects for M-ary APSK are analyzed. The simulated results for PSK lower order modulation signals are in agreement with the results by the analytic model in the order of 1 %. The proper phase noise effects for M-ary APSK modulation signals are deduced by the simulation model. Also, the required signal-to-noise ratios of phase noise are proposed for phase noise degradations, which are used as the design parameter that considers the phase noise effect.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.365.2-365
• /
• 2002

The flow field around a symmetrical airfoil in a uniform flow under the generation of noise was studied by experiments and numerical simulation. The experiments are conducted by visualizing the surface flow over the airfoil with a shear-sensitive liquid-crystal coating and by measuring the instantaneous velocity field around the trailing edge of the airfoil. The numerical simulation was carried out by LES. (omitted)

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.4
• /
• pp.58-64
• /
• 2001

Sound absorbing materials are applied to the exposed surfaces of curvet subway tunnel for the reduction of curving noise level. Before the treatment, acoustical engineering simulation is performed to predict the noise level reduction for different kinds and amounts of absorbing material. The principle of geometrical acoustics is utilized to perform the simulation efficiently and accurately. The noise bevels of the inside and outside of running car body are measured to find the noise level reduction. The average noise level reduction of 8 dB has been attained. It has been shown that the simulated results are comparable to the measured ones.

• KIEAE Journal
• /
• v.9 no.1
• /
• pp.61-68
• /
• 2009

In this study, computer simulation program was using to identify the effects of road traffic noise propagation depending on the road types which are very variable in dense city. To achieve this goal, the roads should adjacent to housing complex were categorized into 7 types and propagation noise level should predicted then after simulation of noise exposure population calculation are carried out. Followings the results. First, the road types producing the higher noise level are R1, R2, R3 and R7. The lowest one is R6. And R4, R5 showed that some amount of noise level reduction. Second. the R6 road type which is tunnel shaped showed the highest noise level reduction in vertical distance gap. Last, the order of noise exposure population ratio is R1>R2>R7 and R6 showed the lowest.