• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.335-336
• /
• 2000

A psychoacoustic model based noise shaping method is proposed, where noise's presence with a host signal will not be perceptually noticeable. The derivation of imperceptible noise levels from the masking thresholds of the signal involves a deconvolution associated with the spreading function in the psychoacoustic model, which results in an ill-conditioned problem. In this paper, the problem is formulated as a constrained optimization, and it is demonstrated that the solution provides noise shaping where the noise excitation level conforms to the masking thresholds of the signal.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.12
• /
• pp.888-894
• /
• 2015

A new method for the simulation of the vehicle's interior road noise is proposed in the present study. The road noise model can synthesize road noise of a vehicle for varying driving speed within a range. In the proposed method, interior road noise is considered as a stochastic time-series, and is modeled by a nonstationary parametric model via two steps. First, each interior road noise signal, obtained from constant speed driving tests performed within a range of speed, is modeled as an autoregressive model whose parameters are estimated by using a standard method. Finally, the parameters obtained for different driving speeds are interpolated based on the varying driving speed to yield a time-varying autoregressive model. To model a full band road noise, audible frequency range is divided into an octave band using a wavelet filter bank, and the road noise in each octave band is modeled.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.564-569
• /
• 2013

An accurate railway environmental noise prediction model is required to make the proper solution of the railway noise problems. In this paper, an engineering model for predicting the noise of conventional passenger cars is presented considering the acoustic source strength in octave-band frequencies and the propagation over grounds with varying surface properties. Since the formation of a train can be variable, the source strength of each locomotive and passenger car was estimated by measuring the pass-by noise and analysing the wheel-rail rolling noise. Some validation cases show on the average small differences between the predictions of the present model and the measurement results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.709-714
• /
• 2008

The various computer programs are used in computer simulation of the traffic noise prediction. But the difference or problem of calculation method used for road traffic noise prediction is not exactly investigated. In this paper, Road traffic noise is predicted on the specific regions by using four prediction methods such as XPS31-133 model(France), RLS-90 model(Germany), ASJ RTN model(Japan) and FHWA model(U.S.A.), which are operated by a program named SoundPLAN, a program to predict road traffic noise. Those prediction values are compared with a measurement value. The results show that four prediction values for taraffic noise are a little different, because of various input factors according to the prediction methods.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.5
• /
• pp.818-824
• /
• 2011

In this paper, we proposed a phase noise model of a frequency synthesizer for a radar system. Especially, it was proposed a phase noise model in a DAS(Direct Analog Synthesizer) and a frequency up converter system using Leeson's model. The proposed phase noise model was derived from the measurement data of model 1 and evaluated by adapting to model 2 and model 3 frequency synthesizers. The prediction phase noise by modeling was totally matched to the measured data and the effective analysis of the phase noise was done in a frequency synthesizer and a frequency converter of radar system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.5
• /
• pp.400-407
• /
• 2011

The suggested method of previous Son's study dichotomized subjective response data to modeling noise exposure-response. The method used maximum liklihood estimation instead of least square estimation and the noise exposure-response curve of the study was logistic regression analysis result. The method was originated to modeling community response rate such as %HA or %A. It can be useful when the subjective response was investigated based on predicted noise level. It is difficult to measure the single source emitting noise such as railway because various traffic noise sources combined in our life. The suggested method was adopted to model in this study and railway noise-exposure response curves were modeled because the noise level of this area was predicted data. The data of this study was used by previous Ko's paper but he dealt the area as combined noise area and divided the data by dominant noise source. But this study used all data of this area because the annoyance response to railway noise was higher than other noise according to the result of correlation analysis. The trend of the %HA and %A prediction model to train noise of this study is almost same as the model based on measured noise of previous Lim's study although the investigated areas and methods were different.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.49 no.8
• /
• pp.442-450
• /
• 2000

Active noise control is an approach to noise reduction in which a secondary noise source that destructively interferes with the unwanted noise. In general, active noise control systems rely on multiple sensors to measure the unwanted noise field and the effect of the cancellation. This paper develops an approach that utilizes a single sensor. The noise field is modeled as a stochastic process, and a time-adaptive algorithm is used to adaptively estimate the parameters of the process. Based on these parameter estimates, a canceling signal is generated. Opppenheim model assumed that transfer function characteristics from the canceling source to the error sensor is only propagation delay. But this paper proposes a modified Oppenheim model by considering transfer characteristics of acoustic device and noise path. This transfer characteristics is adaptively cancelled by adaptive model. This is proved by computer simulation with artifically generated random noise and sine wave noise. The details of the proposed architecture, and theoretical simulation and experimental results of the noise cancellation system for three dimension enclosure are presented in the paper.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.1
• /
• pp.52-59
• /
• 2015

In the conventional model for the prediction of the railway environmental noise, one used an empirical formula of the total noise level at specific distances. Only a function of the distance to the source was also used to calculate the noise level near the railway bridges. However, the noise varies depending on the position of the receiver as well as the distance from the source especially at concrete bridges. In this paper, a noise propagation model in the railway concrete bridge was derived by considering the diffraction at the bridge deck and the ground effect and applying the ISO 9613-2 noise propagation model. We compared the predicted and measured values of environmental noise at a high-speed railway bridge, and it was confirmed that this prediction model gives relatively small errors.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.336-340
• /
• 2014

The noise and vibration have been evaluated by using the finite element model in the vehicle developing stage. The sound pressure of the vehicle compartment is predicted by the acoustic cavity model coupled with the body structure. In general, the structural model has been focused to study in the improvement of the noise. It is not easy to treat the structural model, instead the acoustic cavity model is relatively simple and aids in root cause analysis of vibro-acoustic issues. Therefore, the acoustic transfer function of the cavity is more efficient for finding out the main contribution parts of the vehicle booming noise. And examples about the run-up booming noise demonstrate the validity of the AFT analysis for improving the vibro-acoustic sensitivity.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.3
• /
• pp.125-135
• /
• 2009

An analytical 2-dimensional model to explain the small signal and noise properties of an AlGaN/GaN modulation doped field effect transistor has been developed. The model is based on the solution of two-dimensional Poisson's equation. The developed model explains the influence of Noise in ohmic region (Johnson noise or Thermal noise) as well as in saturated region (spontaneous generation of dipole layers in the saturated region). Small signal parameters are obtained and are used to calculate the different noise parameters. All the results have been compared with the experimental data and show an excellent agreement and the validity of our model.