• Nuclear Engineering and Technology
• /
• 제49권1호
• /
• pp.54-70
• /
• 2017

The accumulator is a passive safety injection device for emergency core cooling systems. As an important safety feature for providing a high-speed injection flow to the core by compressed nitrogen gas pressure during a loss-of-coolant accident (LOCA), the accumulator injects its precharged nitrogen into the system after its coolant has been emptied. Attention has been drawn to the possible negative effects caused by such a nitrogen injection in passive safety nuclear power plants. Although some experimental work on the nitrogen injection has been done, there have been no comparative tests in which the effects on the system responses and the core safety have been clearly assessed. In this study, a new thermal hydraulic integral test facility-the advanced core-cooling mechanism experiment (ACME)-was designed and constructed to support the CAP1400 safety review. The ACME test facility was used to study the nitrogen injection effects on the system responses to the small break loss-of-coolant accident LOCA (SBLOCA) transient. Two comparison test groups-a 2-inch cold leg break and a double-ended direct-vessel-injection (DEDVI) line break-were conducted. Each group consists of a nitrogen injection test and a nitrogen isolation comparison test with the same break conditions. To assess the nitrogen injection effects, the experimental data that are representative of the system responses and the core safety were compared and analyzed. The results of the comparison show that the effects of nitrogen injection on system responses and core safety are significantly different between the 2-inch and DEDVI breaks. The mechanisms of the different effects on the transient were also investigated. The amount of nitrogen injected, along with its heat absorption, was likewise evaluated in order to assess its effect on the system depressurization process. The results of the comparison and analyses in this study are important for recognizing and understanding the potential negative effects on the passive core cooling performance caused by nitrogen injection during the SBLOCA transient.

• 동력기계공학회지
• /
• 제11권4호
• /
• pp.26-31
• /
• 2007

Recently, study on the improvement of combustion performance for the diesel engine by using the impinging spray in the combustion chamber has been actively studied. The purpose of this study is to examine the variation of exhaust emission between the trial engine with impinging plate and the prototype engine in accordance with change of fuel injection timing and fuel injection pressure. The concentration of nitrogen oxide of trial engine decreased more than 50% compared to prototype engine. However, smoke of trial engine indicated very high concentration compared to prototype engine. The effect of fuel injection timing on the nitrogen oxide and smoke indicated different results, that is, the concentration of nitrogen oxide decreased as the degree of fuel injection start become slower, whereas the concentration of smoke decreased as the degree of fuel injection start become faster.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.320-329
• /
• 2008

The influence of thermodynamic transition associated with transcritical nitrogen injection upon the flow structure was investigated to explore numerical simulation of the injectant dynamics of oxygen/hydrogen coaxial jet in liquid rocket engines. Single and coaxial nitrogen jets were treated by comparing the transcritical and perfect-gaseous conditions, wherein the numerical model was accommodative to the real-fluid thermodynamics and transport properties at supercritical pressures. The model was in the first place validated by comparing the results of transcritical nitrogen injection between calculations and available experiments. For a single jet under the transcritical condition, the nitrogen kept a relatively high density up to its pseudo-critical temperature inside the mixing layer, since it remains less expanding until heated up to its pseudo-critical temperature. Numerical analysis revealed that cryogenic jets exhibit strong dependence of specific enthalpy profile upon the associated density profile that are both dominated by turbulent thermal diffusion. In the numerical model, therefore, exact evaluation of turbulent heat fluxes becomes very important for simulating turbulent cryogenic jets under supercritical pressures. Concerning the coaxial jets due to transcritical/gaseous nitrogen injections, the density profile inside the mixing layer was again affected by the thermodynamic transition of nitrogen. However, hydrodynamic instability modes of the inner jet did not show significant differences by this thermodynamic transition, so that further study is needed for the mixing process downstream of the near injection position.

• 동력기계공학회지
• /
• 제19권4호
• /
• pp.82-88
• /
• 2015

The purpose of this study is to investigate the effect of the impinging plate on combustion process in Diesel engine. Especially, the variation of exhaust emission and engine performance by the change of fuel injection timing and fuel injection pressure between the trial engine with impinging plate and the prototype engine were examined. The nitrogen oxide concentration of the trial engine decreased more than 50% compared to the prototype engine, however, smoke concentration of the trial engine indicated higher degree than the prototype engine. The smoke concentration, fuel consumption rate and exhaust gas temperature decreased as the fuel injection timing become faster, whereas the nitrogen oxide concentration decreased as the fuel injection timing is retarded. The nitrogen oxide concentration, fuel consumption rate and exhaust gas temperature decreased as the fuel injection pressure become lower. But smoke concentration decreased as the fuel injection pressure become higher.

• 에너지공학
• /
• 제26권1호
• /
• pp.28-33
• /
• 2017

액화질소 엔진은 유해 배출물질을 전혀 배출하지 않는 고청정 동력기관이며, 에너지 밀도면에서 배터리에 비해 크기 때문에 전기자동차에 대한 경쟁력을 가지고 있다. 기존의 액화질소 엔진은 주로 왕복동 방식에 국한되어 왔다. 본 논문에서는 스크롤 팽창기를 적용하는 액화질소 엔진의 개념을 도입하였다. 스크롤 팽창기를 엔진에 적용할 경우 엔진 효율이 증가할 수 있고, 구조의 단순화 구현이 가능하여 기존 왕복동 방식 엔진에 비해 기술적, 경제적 경쟁력을 가질 수 있다. 본 연구에서는 액체 질소 분사압력을 변화시키면서 스크롤 팽창기가 적용된 액화질소 엔진의 성능을 분석하였다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2015년도 제51회 KOSCO SYMPOSIUM 초록집
• /
• pp.41-44
• /
• 2015

Experimental study was conducted to investigate the effect of ultra-high injection pressure on combustion and emission characteristics in a single-cylinder diesel engine. Electronically controlled ultra-high pressure fuel injection system consistently supplied the fuel of ultra-high pressure up to 250 MPa. Various injection pressures, 40 to 250 MPa, were applied and compared. A injector with eight identical nozzle holes which have diameter of $105{\mu}m$ was used. The results showed high potential to improve the nitrogen oxide (NOx) and particulate matter (PM) trade-off relationship with an ultra-high injection pressure and the exhaust gas recirculation (EGR).

• 항공우주기술
• /
• 제3권1호
• /
• pp.205-212
• /
• 2004

본 연구에서는 액체로켓의 극저온 추진제 공급부에서 요구되는 추진제의 공급 온도를 맞추기 위한 헬륨 가스 분사 냉각에 대한 수류 실험을 수행하여, 헬륨가스 분사에 의한 온도 저감에 대한 실험적 연구를 통한 온도 저감 특성을 고찰하였다. 수류 실험에 사용된 극저온 액체는 액체 질소를 사용하였으며, 냉각을 위한 가스로는 헬륨가스를 사용하였다. 헬륨 분사에 의한 액체 질소 과냉각 현상을 확인할 수 있었으며, v/vL≒0.8min-¹ 조건에서 대략 4분 이내에 최대로 과냉각(subcooling)됨을 알 수 있었다.

• 한국세라믹학회지
• /
• 제32권5호
• /
• pp.559-566
• /
• 1995

Alumina powder was coated with stearic acid and then mixed with isotactic polypropylene, atactic polypropylene as binders at 15$0^{\circ}C$ for 2 hours. The mixture was then injection molded at various mold temperatures using injection molding machine to investigate the effect of the molding temperature and debinding parameters on the formation of the defects. The molded specimens were debinded in both air and nitrogen atmospheres. Wicking and solvent methods were also used to enhance debinding efficiency. The specimens were prefired at 120$0^{\circ}C$ and then sintered at 150$0^{\circ}C$ for 3 hours. Various defects were formed at mold temoperature of 3$0^{\circ}C$, 6$0^{\circ}C$ and 10$0^{\circ}C$ and any noticeable defect was not formed at 85$^{\circ}C$. The density of green body increased with mold temperature. Debinding in air atmosphere was more effective than in nitrogen atmosphere. Results also proved that wicking and solvent treatments helped minimize the number of defects.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권3호
• /
• pp.317-322
• /
• 2011

This work has investigated the exhaust emissions such as Total Hydrocarbon (THC), Nitrogen Oxides(NOx), and Particulate Matter (PM) characteristics emitted from the tail-pipe of a continuously variable valve timing (CVVT) gasoline-fueled engine with different intake valve opening timings and injection pressures at the part load condition. Valve overlap period was varied from $40^{\circ}CA$ to $10^{\circ}CA$ and fuel injection pressure was increased from 3.5 bar to 5.0 bar. THC and NOx emissions decreased as intake valve opening timing was advanced regardless of fuel injection pressure. When the fuel was injected with the condition of 5.0 bar at all of valve overlap ranges, THC levels were reduced by 55%. NOx concentrations were diminished about 75% as valve overlap increased. PM size distributions were analyzed as bi-modal type of the nucleation and accumulation mode. Comparing with fuel injection pressures, PM emission levels were decreased at high pressure injection of 5.0 bar condition.

• 한국정밀공학회지
• /
• 제17권9호
• /
• pp.196-201
• /
• 2000

There is a great demand for reducing the amount of material used in mass-produced plastics parts for material cost constitutes a large percentage of the total cost of a product up to 75% It may be noted that the price of plastics is directly related to the price of petroleum. Material reduction therefore decreases the amount of oil needed for the manufacture of plastics and thus help conserve this natural resource. Therefore microcellular foaming process(MCPs) was studied for solving this problems alternatively in 1980's at M. I. T. Until now in microcellular plastics processes carbon dioxide gas was mainly used for microcellular foaming Because carbon dioxide has more solubility than any other gases such as nitrogen gas or helium gas. The purpose of the this research is measurement of changing of the microcellular plastics' weight by using nitrogen gas in injection molding an comparing weight reduction of microcellular foamed plastics for using carbon dioxide gas with nitrogen gas.