• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.45-48
• /
• 2004

본 논문은 니켈실리사이드 (Ni-Silicide)의 열안정성을 개선하기 위해서 Ti와 TiN capping 층을 이용한 새로운 구조 Ni/Ti/Ni/Tin 구조를 제안하였다. 계면특성과 열안정성을 향상시키기 위해 타이타늄(Ti)을 니켈(Nickel) 사이에 적용하고, 니켈 실리사이드 형성 시 산소와의 반응을 억제하여 실리사이드의 응집현상을 개선시키고자 TiN capping을 적용 하였다. 니켈 실리사이드의 형성온도에 따른 $NiSi_2$로의 상변이를 억제할 수 있었고, 열안정성 평가를 위한 $700^{\circ}C$, 30분간 고온 열처리에서도 제안한 구조로 니켈실리사이드의 단면특성과 19 % 정도 면저항 특성을 개선하였다.

• Nuclear Engineering and Technology
• /
• 제48권3호
• /
• pp.773-777
• /
• 2016

A betavoltaic battery was prepared using radioactive $^{63}Ni$ attached to a three-dimensional single trenched P-N absorber. The optimum thickness of a $^{63}Ni$ layer was determined to be approximately $2{\mu}m$, considering the minimum self-shielding effect of beta particles. Electroplating of radioactive $^{63}Ni$ on a nickel (Ni) foil was carried out at a current density of $20mA/cm^2$. The difference of the short-circuit currents ($I_{sc}$) between the pre- and post-deposition of $^{63}Ni$ (16.65 MBq) on the P-N junction was 5.03 nA, as obtained from the I-V characteristics. An improved design with a sandwich structure was provided for enhancing performance.

• 센서학회지
• /
• 제24권6호
• /
• pp.379-384
• /
• 2015

An infrared image sensor is a core device in a thermal imaging system. The fabrication method of a focal plane array (FPA) is a key technology for a high resolution infrared image sensor. Each pixels in the FPA have $Si_3N_4/SiO_2$ membranes including legs to deposit bolometric materials and electrodes on Si readout circuits (ROIC). Instead of polyimide used to form a sacrificial layer, the feasibility of an amorphous silicon (${\alpha}-Si$) was verified experimentally in a $8{\times}8$ micro-bolometer array with a $50{\mu}m$ pitch. The elimination of the polyimide sacrificial layer hardened by a following plasma assisted deposition process is sometimes far from perfect, and thus requires longer plasma ashing times leading to the deformation of the membrane and leg. Since the amorphous Si could be removed in $XeF_2$ gas at room temperature, however, the fabricated micro-bolomertic structure was not damaged seriously. A radio frequency (RF) sputtered nickel oxide film was grown on a $Si_3N_4/SiO_2$ membrane fabricated using a low stress silicon nitride (LSSiN) technology with a LPCVD system. The deformation of the membrane was effectively reduced by a combining the ${\alpha}-Si$ and LSSiN process for a nickel oxide micro-bolometer.

• 열처리공학회지
• /
• 제23권5호
• /
• pp.245-248
• /
• 2010

Sn doped $In_2O_3$ (ITO) and ITO/Ni/ITO (INI) multilayer films were deposited on the glass substrates with a reactive magnetron sputtering system without intentional substrate heating and then the influence of the Ni interlayer on the methanol gas sensitivity of ITO and INI film sensors were investigated. Although both ITO and INI film sensors have the same thickness of 100 nm, INI sensors have a sandwich structure of ITO 50 nm/Ni 5 nm/ITO 45 nm. The changes in the gas sensitivity of the film sensors caused by methanol gas ranging from 100 to 1000 ppm were measured. It is observed that the INI film sensors show the higher sensitivity than that of the ITO single layer sensors. Finally, it can be concluded that the INI film sensor have the potential to be used as improved methanol gas sensors.

• 한국재료학회지
• /
• 제33권5호
• /
• pp.214-221
• /
• 2023

As a filler metal for lowering the melting point of Ag, many alloy metal candidates have emerged, such as cadmium, with zinc, manganese, nickel, and titanium as active metals. However, since cadmium is known to be harmful to the human body, Cd-free filler metals are now mainly used. Still, no study has been conducted comparing the characteristics of joints prepared with and without cadmium. In addition, studies have yet to be conducted comparing the typical characteristics of brazing filler metals with special structures, and the joint characteristics of brazing filler metals with available frames. In this study, the characteristics of junctions of silver-based intercalation metals were compared based on the type of filler metal additives, using a special structure, a filler metal sandwich structure, to protect the internal base metal. The general filler metal was compared using the structure, and the thickness of the filler metal according to the thickness was reached. A comparison of the characteristics of the junction was conducted to identify the characteristics of an intersection of silver-based brazing filler metal and the effect on joint strength. Each filler metal's collective tensile strength was measured, and the relationship between joint characteristics and tensile joint strength was explored. The junction was estimated through micro strength measurement, contact angle measurement with the base metal when the filler metal was melted, XRD image observation, composition analysis for each phase through SEM-EDS, and microstructure phase acquisition.

• 한국진공학회지
• /
• 제20권3호
• /
• pp.195-199
• /
• 2011

RF 마그네트론 스퍼터와 DC 마그네트론 스퍼터를 병행하여 ITO/Au/ITO, ITO/Cu/ITO, 그리고 ITO/Ni/ITO 박막을 유리기판 위에 증착하였다. 증착 후 진공열처리를 통하여 층간 금속 층이 ITO박막의 메탄올 검출 민감도에 미치는 영향을 분석하였다. 모든 박막센서의 두께는 100 nm로 동일하게 ITO 50 nm/metal 10 nm/ITO 40 nm로 제작되었고 메탄올 농도는 100에서 1,000 ppm까지 달리하였다. ITO/Au/ITO 박막센서가 가장 높은 민감도를 보임으로써 ITO/Au/ITO 다층박막이 기존의 ITO메탄올 센서를 대체할 수 있는 센서임을 확인하였다.