• Journal of Power System Engineering
• /
• v.15 no.2
• /
• pp.42-48
• /
• 2011

440A martensitic stainless steels which were modified with reduced carbon content(~0.5%) and addition of small amount of nickel, vanadium, tungsten and molybdenum were manufactured. Effects of alloying elements and tempering temperatures on the uniform corrosion in the solution of lN H2S04 were investigated through the electrochemical polarization test. When tempering temperature is constant, corrosion current density in active-passive transition point, Icorr, decreased a little with an increase of austenitizing temperature. In addition to this, when austenitizing temperature is constant, longer holding time showed a little lower Icorr and Ipass, passive current density. And when austenitized at $1050^{\circ}C$ and tempered in a range of $350{\sim}750^{\circ}C$, best anti-corrosion properties were obtained at $350^{\circ}C$ tempering temperature while worst at $450^{\circ}C$ or $550^{\circ}C$. The specimens tempered at below $450^{\circ}C$ and above $550^{\circ}C$, similar and good anti-corrosion characteristics were obtained regardless of alloying elements added, showing anti-corrosion characteristics are influenced more by tempering temperature than by alloying elements.

• Nuclear Engineering and Technology
• /
• v.38 no.4
• /
• pp.391-398
• /
• 2006

It is recommended to clean steam generators of nuclear power plants during plant outages. Under normal operations, sludge is created and constantly accumulates in the steam generators. The constituents of this sludge are different depending on each power plant characteristics. The sludge of the Kori Unit 1 steam generator, far example, was found to be composed of 93% ferrous oxide, 3% carbon and 1% of silica oxide and nickel oxide each. The research to develop a lancing system that would remove sludge deposits from the tubesheet of a steam generator was started in 1998 by the Korea Electric Power Research Institute (KEPRI) of the Korea Electric Power Corporation (KEPCO). The first commercial domestic lancing system in Korea, the $KALANS^(R)-I$ Lancing System, was completed in 2000 for Kori Unit 1 for cleaning the tubesheet of its Westinghouse Delta-60 steam generator. Thereafter, the success of the development and site implementation of the $KALANS^(R)-I$ lancing system for YGN Units 1&2 and Ulchin Units 3&4 was also realized in 2004 for sludge removal at those sites. The upper bundle cleaning system for Westinghouse model F steam generators is now under development.

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.615-621
• /
• 1999

The new process in order to fabricate of Ni catalyst with high activity by the mechanochemical(MC) method which was combined the mechanical alloying(MA) and the chemical treatment process. The microstructure and characterization of mechanically alloyed Ni-5-wt% Al powder and Ni catalyst gained by alkali leaching were investigated byt he various analysis such as XRD, SEM-EDS, HRTEM and laser particle analyzer. The steady state powder with 1~2$\mu\textrm{m}$ mean particle size was obtained after 30hr milling with the PCA of 2 wt% stearic acid under the condition of grinding stainless steel ball to powder ratio of 60:1 and rotating speed fo 300rpm. According to result of HRTEM diffraction pattern, MA powder of the steady state was nanocrystalline $Al_3$$Ni_2$ intermetallic compound. Ni catalyst was obtained after KOH leaching of the steady state powder was about 20nm nanocrystalline which contained about 8 wt % Al.

• Structural Engineering and Mechanics
• /
• v.68 no.5
• /
• pp.519-526
• /
• 2018

In this article, experimental training of the commercial available shape memory alloy fibre (SMA) fibre under the combined thermomechanical loading is reported. SMA has the ability to sense a small change in temperature (${\geq}10^{\circ}C$) and activated under the external loading and results in shape change. The thermomechanical characteristics of SMA at different temperature and mechanical loading are obtained through an own lab-scale experimental setup. The analysis is conducted for two types of the medium using the liquid nitrogen (cold cycle) and the hot water (heat cycle). The experimental data indicate that SMA act as a normal wire for Martensite phase and activated behavior i.e., regain the original shape during the Austenite phase only. To improve the confidence of such kind of behavior has been verified by inspecting the composition of the wire. The study reveals interesting conclusion i.e., while SMA deviates from the equiatomic structure or consist of foreign materials (carbon and oxygen) except nickel and titanium may affect the phase transformation temperature which shifted the activation phase temperature. Also, the grain structure distortion of SMA wire has been examined via the scanning electron microscope after the thermomechanical cycle loading and discussed in details.

• Economic and Environmental Geology
• /
• v.17 no.1
• /
• pp.17-34
• /
• 1984

The Ordovician limestone and dolomite was mineralized by the intrusion of quartz porphyry to form hydrothermal ore deposit along the fault shear zone, which trends $N30^{\circ}-40^{\circ}W$ dipping $60^{\circ}-70^{\circ}SW$. The primary manganese carbonates in the upper part of the deposit were oxidized to form supergene manganese ore deposits. The quartz porphyry is plotted mainly in granite region of the triangular diagram of normative composition. The granite phase contains more copper and lead, but less zinc, nickel and chromium than the granodiorite phase which occupies the northwestern part of the quartz porphyry. The content of copper, lead, zinc, nickel and chromium in the quartz porphyry is lower compared with the granitic rocks from the copper province in the Gyeongsang basin. But the granitic rocks from the lead-zinc province has lower content of copper and nickel than the quartz porphyry. The primary distribution pattern of trace elements in the country rock of limestone and dolomite has close relation with the hydrothermal mineralization, showing anomalous or high content near the fault shear zone. The secondary distribution pattern of trace elements in soils shows close relation with the solubility of the carbonates of the elements under weathering condition.

• Journal of Powder Materials
• /
• v.13 no.5 s.58
• /
• pp.327-335
• /
• 2006

In the development of new hydrogen absorbing materials for a next generation of metal hydride electrodes for rechargeable batteries, metastable Mg-Ni-based compounds find currently special attention. Amor phous-nanocrystalline $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ alloys were produced by mechanical alloying and melt-spinning and characterized by means of XRD, TEM and DSC. On basis of mechanically alloyed Mg-Ni-Y powders, complex hydride electrodes were fabricated and their electrochemical behaviour in 6M KOH (pH=14,8) was investigated. The electrodes made from $Mg_{63}Ni_{30}Y_7$ powders, which were prepared under use of a SPEX shaker mill, with a major fraction of nanocrystalline phase reveal a higher electrochemical activity far hydrogen reduction and a higher maximum discharge capacity (247 mAh/g) than the electrodes from alloy powder with predominantly amorphous microstructure (216 mAh/g) obtained when using a Retsch planetary ball mill at low temperatures. Those discharge capacities are higher that those fur nanocrystalline $Mg_2Ni$ electrodes. However, the cyclic stability of those alloy powder electrodes was low. Therefore, fundamental stability studies were performed on $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ ribbon samples in the as-quenched state and after cathodic hydrogen charging by means of anodic and cathodic polarisation measurements. Gradual oxidation and dissolution of nickel governs the anodic behaviour before a passive state is attained. A stabilizing effect of higher fractions of yttrium in the alloy on the passivation was detected. During the cathodic hydrogen charging process the alloys exhibit a change in the surface state chemistry, i.e. an enrichment of nickel-species, causing preferential oxidation and dissolution during subsequent anodization. The effect of chemical pre-treatments in 1% HF and in $10\;mg/l\;YCl_3/1%\;H_2O_2$ solution on the surface degradation processes was investigated. A HF treatment can improve their anodic passivation behavior by inhibiting a preferential nickel oxidation-dissolution at low polarisation, whereas a $YCl_3/H_2O_2$ treatment has the opposite effect. Both pre-treatment methods lead to an enhancement of cathodically induced surface degradation processes.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.5 no.6
• /
• pp.431-435
• /
• 2000

The goal of this research is to compare the metal binding characteristics of an anoxic selector activated sludge system and a conventional activated sludge system. Metal biosorption by biomass harvested from experimental systems was determined by a series of batch experiments. Heavy metals studied in this research were zinc, cadmium, and nickel. The sorption isotherm showed that the selector sludge had significantly higher sorption capacity than did the control sludge. Metal biosorption behavior closely followed a Freundlich isotherm model for equilibrium concentrations. ECP contents of biomass estimated by alkali extraction technique showed that ECP levels in the selector sludge significantly higher than that in the sludge harvested from the conventional system, indicating that the higher metal sorption capacity of selector sludge may be due to the selection of the ECP-producing bacteria (i.e., Zoogloea sp.) by the selector system.

• Journal of the Korean Chemical Society
• /
• v.12 no.2
• /
• pp.38-38
• /
• 1968

The conductivity of polycrystalline NiO is measured in the temperature range of $200^{\circ}C\; to\; 800^{\circ}C$ under oxygen pressures from $1.52{\times}10^2\; mmHg\; to\; 10^{-4}$ mmHg. The plots of the log ${\sigma}$ vs 1/T at constant oxygen pressure are found to be linear and the activation energies obtained from the slopes of these plots show that the energies are greater under high oxygen pressure than under low pressure. The transition points are found from the curves. The dependence of the conductivity on the $O_2$ pressure, in the above temperature range, is to be regular but it does not obey the theoretical expression, i.e.${\sigma}σ = K_{ox}P^{1/6}.$ The activation energies are calculated from the curves at the various condition.

• Journal of the Korean Chemical Society
• /
• v.12 no.2
• /
• pp.39-43
• /
• 1968

The conductivity of polycrystalline NiO is measured in the temperature range of $200^{\circ}C\;to\;800^{\circ}C$ under oxygen pressures from $1.52{\times}10^2\;mmHg\;to\;10^{-4}$ mmHg. The plots of the log ${\sigma}$ vs 1/T at constant oxygen pressure are found to be linear and the activation energies obtained from the slopes of these plots show that the energies are greater under high oxygen pressure than under low pressure. The transition points are found from the curves. The dependence of the conductivity on the $O_2$ pressure, in the above temperature range, is to be regular but it does not obey the theoretical expression, i.e. ${\sigma}=K_{ox}P^{1/6}.$ The activation energies are calculated from the curves at the various condition.

• The Korean Journal of Ceramics
• /
• v.4 no.2
• /
• pp.156-161
• /
• 1998

We have measured changes of the non-stoichiometry, $\Delta\delta$, in Fe-doped nicked oxide , by thermogravimetry for four iron fractions, x=0.01, 0.031, 0.057 and 0.10, and three temperatures, T=1273, 1373 and 1473 K. The obtained data can be modelled by a defect structure in which substitutional trivalent iron ions, FeNi, are compensated by cation vacancies, $V_{Ni}$", and (4:1)-clusters. These clusters consist of tetravalent interstitial iron, $Fe_i\;^4$