• Journal of the Korean Magnetics Society
• /
• v.3 no.2
• /
• pp.115-120
• /
• 1993

The relationship between magnetic parameter and microwave absorbing performance evaluation factor of electomagnetic wave absorber such as matching frequency, matching thickness were investigated for Ni-Zn ferrite composites. It was identified that the maximum value of ${\mu}_{r}$" is shift to low frequency with decrese Ni/Zn ratio and the value of ${\mu}_{r}$" is maximum in the case of Ni/Zn=1. All Ni-Zn ferrite composites in this study have two matching frequencies in 1-12 GHz frequency. It can be suggested that $f_{m1}$ is proportional to resonance frequency and $f_{m2}$ is proportional to the saturation magnetization.

• Journal of the Korean Magnetics Society
• /
• v.7 no.1
• /
• pp.19-24
• /
• 1997

Composition and process conditions for low temperature sintered NiCuZn ferrites were investigated, so as to fabricate multilayered chip inductor. The$Fe_2O_3$ deficiency for low temperature sintering was decreased with NiO contents of NiCuZn ferrites. The permeability of NiCuZn ferrites can be controlled in the range of 12~562 with the variation of NiO and $Co_3O_4$ contents. The $Q_{max} $ frequency of NiCuZn ferrites was decreased from 50 MHz to 3 MHz linearly with permeability increase from 60 to 560. The relation between the $Q_{max}$ frequency(Y) and permeability(X) of NiCuZn ferrites was expressed with the following empirical equation, logY=4.2-1.4logX.

• Journal of the Korean Ceramic Society
• /
• v.39 no.12
• /
• pp.1119-1123
• /
• 2002

Nanostructured spinel NiZn ferrites were prepared by the sol-gel method from metal nitrate raw materials. Analyses by X-ray diffraction and scanning electron microscopy showed the average particle size of NiZn ferrite was under 50 nm. The single phase of NiZn ferrites was obtained by firing at 250${\circ}C$, resulting in nanoparticles exhibiting normal ferrimagnetic behavior. The nanostructured $Ni_{1-X}Zn_XFe_2O_4$ (x=0.0∼1.0) were found to have the cubic spinel structure of which the lattice constants ${\alpha}_2$ increases linearly from 8.339 to 8.427 ${\AA}$ with increasing Zn content x, following Vegard's law, approximately. The saturation magnetization $M_s$ was 48 emu/g for x=0.4 and decreased to 8.0 emu/g for higher Zn contents suggesting the typical ferrimagnetism in mixed spinel ferrites. Pure NiZn ferrite phase substituted by Cu was observed before using the additive but hematite phase was partially appeared at $Ni_{0.2}Zn_{0.2}Cu_{0.6}Fe_2O_4$. On the other hand, the hematite phase in this NiZn Cu ferrite was disappeared after using the additive of acethyl aceton with small amount. The saturation magnetization Ms of $Ni_{0.2}Zn_{0.8-y}Cu_yFe_2O_4$(y=0.2∼0.6) as measured was about 51 emu/g at 77K and 19 emu/g at room temperature, respectively.

• Journal of Magnetics
• /
• v.18 no.4
• /
• pp.428-431
• /
• 2013

We demonstrate that a partial loading of $Ni_{0.5}Zn_{0.5}Fe_2O_4$ (Ni-Zn ferrite) film remarkably improves impedance matching of electrically small $Ba_3Co_2Fe_{24}O_{41}$ ($Co_2Z$) hexaferrite antenna. A 3 ${\mu}m$ thick Ni-Zn ferrite film was deposited on a silicon wafer by the electrophoresis deposition process and post-annealed at $400^{\circ}C$. The fabricated Ni-Zn ferrite film has saturation magnetization of $268emu/cm^3$ and coercivity of 89 Oe. A partial loading of the Ni-Zn ferrite film on the $Co_2Z$ hexaferrite helical antenna increases antenna return loss to 24.7 dB from 9.0 dB of the $Co_2Z$ antenna. Experimental results show that impedance matching and maximum input power transmission to the antenna without additional matching elements can be realized, while keeping almost the same size as the $Co_2Z$ antenna size.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.109-113
• /
• 2002

본 연구에서는 공침법에 의한 초미세분말을 이용하여 제조된 (NiCuZn)-ferrite와 건식법을 이용하여 제조된 (NiCuZn)-ferrite의 저온소결 특성 및 전자기적 특성을 상호 비교 분석하였다. 조성은 (N $i_{0.4-x}$C $u_{x}$Z $n_{0.6}$)$_{1+w}$(F $e_2$ $O_4$/)$_{1-w}$에서 x의 값을 0.2, w의 값은 0.03으로 고정하였고, 소결은 공침법으로 합성된 분말의 경우 초기열처리과정을 거쳐 최종적으로 90$0^{\circ}C$에서, 건식법의 경우 11$50^{\circ}C$의 온도에서 진행하였다. 그 결과, 공침법으로 제조된 (NiCuZn)-ferrite는 건식법으로 제조된 (NiCuZn)-ferrite보다 20$0^{\circ}C$이상 낮은 소결온도에서 높은 소결밀도 값을 가졌으며, 품질계수 등 칩 인덕터에서 중요한 요소인 전자기적 특성이 우수하게 나타났다. 또한, 공침법으로 합성된 페라이트는 분말의 초기열처리온도에 따라 최종소결 특성이 크게 변하였다. 그밖에 공침법과 건식법으로 합성한 (NiCuZn)-ferrite의 결정성, 미세구조들을 XRD, SEM, TEM을 이용하여 비교 고찰하였다.하였다.다.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1355-1357
• /
• 1997

In this study, the ferrite/rubber composite microwave absorbers mixed Ni-Zn ferrite and $Ni_2Y$ ferroxplana were prepared in order to control matching condion. The variation of the material constants($\dot{\varepsilon}$, $\dot{\mu}$) and microwave absorbing characteristics were investigated with various ferrite mixing ratio. The material constants of ferrite/rubber composite microwave absorber could be controlled by variation ferrite mixing radio. The matching frequency and thickness could be controlled with various ferrite mixing ratio.

• Journal of the Korean Ceramic Society
• /
• v.40 no.1
• /
• pp.31-36
• /
• 2003

In this study, nano-sized NiCuZn-ferrites for the multi-layered chip inductor application were prepared by a coprecipitation method and its electromagnetic properties were analyzed. Also, the property of low temperature sintering were studied with the initial heat treatment of powder.$(Ni_{0.4-x}Cu_xZn_{0.60})_{1+w}(Fe_2O_4)_{1-w}$ (x=0.2, w=0.03) were calcined at $300^{circ}C~750^{circ}C.$ The sintered NiCuZn-ferrites at $900^{\circ}C$ showed good apparent density $4.90g/cm^3,$ and magnetic properties of initial permeability 164 and quality factor 72. As the calcination temperature increase, the grain size of NiCuZn-ferrite increased with irregular grain distribution and its magnetic properties were deteriorated.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.165-168
• /
• 2002

본 연구에서는 칩인덕터 코어 소재로 사용되는 (NiCuZn)-ferrite를 습식합성법을 이용하여 나노크기의 초미세 분말을 합성하였으며, 합성된 (ZiCuZn)-ferrite 의 제조공정 및 전파기적 특성에 관하여 고찰하였다. 조성은 (N $i_{0.4-x}$C $u_{x}$Z $n_{0.6}$)$_{1+w}$ (F $e_2$ $O_4$)$_{1-w}$에서 x의 값을 0.05~0.25 범위로 변화시켰으며, w 값은 0.03으로 고정하였다. 소결은 8$50^{\circ}C$에서 9$50^{\circ}C$의 범위에서 진행하였다. 나노크기의(NiCuZn)-ferrite를 사용함으로서 시약급 원료로 제조된 것보다 소결온도를 낮출 수 있었고, 밀도가 높은 페라이트 소결체를 얻을 수 있었다. 또한 초투자율, 품질계수 등 전자기적 특성이 우수하게 나타났다. 그 밖에 습식합성법으로 합성한 (NiCuZn)-ferrite 의 결정성, 미세구조 등을 XRD, SEM 을 이용하여 고찰하였다.하였다.다.

• Korean Journal of Materials Research
• /
• v.14 no.5
• /
• pp.338-342
• /
• 2004

Ni-Zn ferrite powder was obtained by wet method that was to be coprecipitated the metal nitrates, Fe($NO_3$)$_3$ㆍ$9H_2$O, Ni($NO_3$)$_2$ㆍ$6H_2$O, Zn($NO_3$)$_2$ㆍ$6H_2$O to make a high permeability material. The composition of the ferrite powder was $Fe_2$$O_3$ 52 mol%, NiO 14.4 mol%, ZnO 33.6 mol%. Ni-Zn ferrite powder was compounded by precipitating metal nitrates with NaOH in vessel at the synthetic temperature of $90^{\circ}C$ for 8 hours. Calcination temperature and sintering temperature were $700^{\circ}C$ and $1150^{\circ}C$～$1250^{\circ}C$, respectively, for 2 hours. And the other ferrite powder was also prepared by the wet ball milling that was to be mixed the metal oxides as same as the above chemical composition. We studied the properties of the powder and the electromagnetic characteristics of the sintered cores obtained from there two different processes. Wet direct process produced smaller particle size with narrower distribution of the size and more purified ferrite whose sintered cores had high permeability and high magnetization.

• Journal of the Korean Magnetics Society
• /
• v.9 no.4
• /
• pp.217-222
• /
• 1999

The pick up impurity was studied for preparing the NiCuZn ferrite powder by a ball milling method that usually uses in the industrial ceramic process. The raw materials of NiO, CuO, ZnO, and $Fe_2O_3$ powder were weighted according to various spinel composition and mixed for 18 hrs by a wet ball milling method after that the slurry was followed by spray dried and calcined at $700^{\circ}C$ 3 hrs. The calcined NCZF powder was finally ball milled during 65 hrs as same method. The stainless steel ball and jar are used as mixing and milling equipment and the solid concentration of the slurry was 25 vol%. The impurities, stainless steel pickup, were effected by the composition of raw materials especially iron oxide, nickel oxide in the mixing process and by the rate of calcine of NiCuZn ferrite in final milling process. The empirical equation of stainless steel pickup was driven in the wet ball milling system. Finally, the composition of NiCuZn ferrite could be controlled by the empirical equation.