• Journal of Welding and Joining
• /
• v.31 no.3
• /
• pp.76-83
• /
• 2013

This study investigated the effect of bonding temperature and holding time on microstructures and mechanical properties of diffusion bonded joint of Haynes230. The diffusion bonds were performed at the temperature of 950, 1050, and $1150^{\circ}C$ for holding times of 30, 60, 120 and 240 minutes at a pressure of 4MPa under high vacuum condition. The amount of non-bonded area and void observed in the bonded interface decreased with increasing bonding temperature and holding time. Cr-rich precipitates at the linear interface region restrained grain migration at $950^{\circ}C$ and $1050^{\circ}C$. However, the grain migration was observed in spite of short holding time due to the dissolution of precipitates to base metal in the interface region at $1150^{\circ}C$. Three types of the fracture surface were observed after tensile test. The region where the coalesce and migration of grain occurred much showed high fracture load because of base metal fracture whereas the region where those did less due to the precipitates demonstrated low fracture load because of interface fracture. The expected fracture load could be derived with the value of fracture area of base metal ($A_{BF}$) and interface ($A_{IF}$), $Load=201A_{BF}+153A_{IF}$. Based on this equation, strength of base metal and interface fracture were calculated as 201MPa and 153MPa, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.386-386
• /
• 2011

탄소나노튜브는 큰 길이 대 직경 비와 뛰어난 전기적 특성으로 인해 차세대 전계 방출 소자로 주목 받고 있다. 실질적인 전계방출 디스플레이로의 응용을 위한 대면적 제작과 유리 기판 사용을 위해 이용되었던 페이스트(paste)법은 높은 전기장 하에서 장시간 전계방출시 탄소나노튜브 전계방출원과 페이스트(paste)간의 낮은 접착력 때문에 발생하는 탄소나노튜브의 탈루현상(omission)과 유기물질(organic paste)에서 발생하는 탈기체(out-gassing) 문제점이 있었다. 최근 이런 문제점을 개선하기 위해 유기물질(organic paste)를 대체하여 금속바인더(metal binder) 물질을 사용한 결과들이 보고되고 있다. 본 연구에서는 유리기판 위에 제작된 탄소나노튜브 전계방출원의 수명 향상을 위하여 금속바인더와 후속 열처리법의 변화에 따른 전계방출 안정성을 분석하였다. 금속바인더는 접합층/ 접착층(soldering layer/ adhesive layer)으로 구성되어 있으며, 일반적인 소다석회유리(soda-lime glass)에 스퍼터(DC magnetron sputtering system)를 이용하여 증착하였다. 접착층은 유리기판과 접합층의 접착력 향상을 위해 사용되며, 접합층은 기판과 탄소나노튜브 전계방출원을 접합하는 역할과 전계방출 측정시 전극이 되기 때문에 우수한 전기 전도성과 내산화성을 필요로 한다. 본 실험에서는 일반적으로 유리기판과 접착력이 좋다고 알려진 Cr, Ti, Ni, Mo을 접착층으로 사용하였으며, 접합성과 전기전도성, 내산화성이 뛰어난 귀금속 계열의 금속을 접합층으로 사용하였다. 탄소나노튜브를 1,2-디클로로에탄(1,2-dichloroethane, DCE)에 분산시킨 용액을 스프레이방법을 이용하여 증착시켰으며, 후속 열처리 방법을 통하여 접합층과 결합시켰다. 금속바인더와 후속 열처리법의 변화에 따른 접착력과 표면형상(morphology)의 변화를 주사전자현미경(scanning electron microscopy)를 이용하여 분석하였으며, 다이오드 타입에 디씨 바이어스(DC bias)를 사용하여 전계방출특성을 측정하였다[1,2].

• Restorative Dentistry and Endodontics
• /
• v.28 no.1
• /
• pp.41-49
• /
• 2003

There are increasing usage of Nickel-Titanium rotary files in modern clinical endodontic treatment because it is effective and faster than hand filing due to reduced step. This study was conducted to evaluate the effect of canal preparations using 3 different rotary Nickel-Titanium files that has different cross sectional shape and taper on the maintenance of canal curvature. Simulated resin block were instrumented with Profile(Dentsply, USA), GT rotary files(Dentsply, USA), Hero 642(Micro-Mega France), and Pro-Taper(Dentsply, USA). The image of Pre-instrumentation and Post-instrumentation were acquired using digital camera and overspreaded in the computer. Then the total differences of canal diameter, deviation at the outer portion of curvature, deviation at the inner portion of curvature, movement of center of the canal and the centering ratio at the pre-determined level from the apex were measured. Results were statistically analyzed by means of ANOVA, followed by Scheffe test at a significance level of 0.05. The results were as follows； 1. Deviation at the outer portion of curvature, deviation at the inner portion of curvature were showed largest in Pro-Taper so also did in the total differences of canal diameter(p＜0.05). 2. All the groups showed movements of center Profile combined with GT rotary files and Hero 642 has no difference but Pro-Taper showed the most deviation(p＜0.05). 3. At the 1, 2, 3mm level from the apex movements of center directed toward the outer portion of curvature, but in 4, 5 mm level directed toward the inner portion of curvature(p＜0.05). As a results of this study, it could be concluded that combined use of other Nickel-Titanium rotary files is strongly recommended when use Pro-Taper file because it could be remove too much canal structure and also made more deviation of canal curvature than others.

• Economic and Environmental Geology
• /
• v.7 no.3
• /
• pp.87-100
• /
• 1974

This paper deals with grain size analysis, heavy mineral analysis and trace element analysis of the recent sediments of Han River basin between Cheongpyong, Gyeonggi province and Seoul. For each location the samples are taken at river shoreline, river berm and river dune. The size analysis discloses that the mean values range from $-1.37{\phi}$ to $-1.60{\phi}$, sorting values range from 0.25 to 1.84, skewness values range from -0.44 to 0.51 and kurtosis values range from -0.1 to 1.75. Based on the textural parameters, the dune sand can be distinguished from the shoreline-berm sand. The content of heavy minerals of each sample ranges from 0.04 to 4.7%. The principal heavy minerals are ilmenite, magnetite, leucoxene, garnet, amphibole, pyroxene, kyanite, zircon, monazite, tourmaline, epidote, limonite, and minor minerals are apatite, sillimanite, andalusite and olivine. In general, dune sand samples contain more heavy minerals than the samples of shoreline or berm sand. This suggests that the heavy mineral concentration is affected by wind action more than by any other causes. The content of ilmenite and leucoxene decreases, whereas the content of zircon and epidote increases as it approaches the downstream region. The differences result from the variance of geological occurrences. The emission spectrochemical analysis and colorimetry analysis revealed that the content of Ni and V in the heavy minerals of the study area are higher than those of other stream sediments in Korea. On the other hand the content of Cu, Ph, Zn, Mo, W, P, Mn, Cr, Ag and Sn are lower in the study area. It has been observed also that the contents of all the elements except for Bi are higher in this area than the samples of marine sediments of Yellow Sea.

• The Journal of the Korean dental association
• /
• v.52 no.12
• /
• pp.734-743
• /
• 2014

Objectives: By introduced reciprocation motion file in dentistry, dentists benefit simple canal shaping procedure and time-saving. But, reciprocation motion generates uncomfortable vibration to doctors and patients. Because there was no study about this consideration, this study compared vibration pattern and power generated from reciprocation motion motor and conventional rotary motor. Materials & Methods: One conventional rotary motor; X-Smart (Dentsply Maillefer, Ballaigues, Switzerland); and two reciprocating motors; WaveOne Motor (Dentsply Maillefer, Ballaigues, Switzerland) and X-SMART PLUS (Dentsply Maillefer, Ballaigues, Switzerland); were used in this study. Triaxial $ICP^{(R)}$ Accelerometer (Model 356A12, PCB piezotronics, New York, USA) was attached on motor's handpiece head, and was measured tri-axial vibratory acceleration with NI Sound and Vibration Assistant 2009 software (National Instruments, Texas, USA). Mean vibratory acceleration and maximum vibratory acceleration was measured on fixed position and handed position. The results of vibratory acceleration were statistically analyzed using ANOVA and multiple comparisons are made using Turkey's test at p<0.05 level. Results: Reciprocating motors showed higher mean vibratory acceleration and maximum vibratory acceleration than conventional rotary motor (p<0.05). Between reciprocating motors, X-SMART PLUS had lower mean vibratory acceleration and maximum vibratory acceleration than WaveOne Motor (p<0.05). Conclusion: Reciprocating motors generate more vibration than conventional rotary motor. Further study about effect of vibration to dentist and patient is needed. And it seems to be necessary to make a standard about vibration level in endodontic motors.

• Corrosion Science and Technology
• /
• v.9 no.5
• /
• pp.187-195
• /
• 2010

Hyper duplex stainless steels have been developed in Korea for the purpose of application to the seawater system of Korean nuclear power plants. This system supplies seawater to cooling water heat exchanger tubes, related pipes and chlorine injection system. In normal operation, seawater is supplied to heat exchanger through the exit of circulating water pump headers, and the heat exchanged sea water is extracted to the discharge pipes in circulating water system connected to the circulating water discharge lines. The high flow velocity of some part of seawater system in nuclear power plants accelerates damages of components. Therefore, high strength and high corrosion resistant steels need to be applied for this environment. Hyper duplex stainless steel (27Cr-7.0Ni-2.5Mo-3.2W-0.35N) has been newly developed in Korea and is being improved for applying to nuclear power plants. In this study, the physical & mechanical properties and corrosion resistance of newly developed materials are quantitatively evaluated in comparative to commercial stainless steels in other countries. The properties of weld & HAZ (heat affected zone) are analyzed and the best compositions are suggested. The optimum conditions in welding process are derived for ensuring the volume fraction of ferrite(${\alpha}$) and austenite(${\gamma}$) in HAZ and controlling weld cracks. For applying these materials to the seawater heat exchanger, CCT and CPT in weldments are measured. As a result of all experiments, it was found that the newly developed hyper duplex stainless steel WREMBA has higher corrosion resistance and mechanical properties than those of super austenitic stainless steels including welded area. It is expected to be a promising material for seawater systems of Korean nuclear power plants.

• Journal of Digital Contents Society
• /
• v.12 no.3
• /
• pp.371-382
• /
• 2011

Reading and writing in the past make noble significance in 'narration', in other words, in 'the creation of narration', through the process of 'recording'; but in the modern times, it engenders controversies over narration and linearity. In other words, reading/writing in digital era, is devalued as the simple arrangement of test or the connection of vast information without narration nor linearity. However, the reading/writing through text and hypertext reading is not the phenomenon which should be criticized because of the lack of narration or linearity-not only the lack of narration and linearity -, a process of social and cultural transition; it should be revalued as a result. The change of reading and writing methods will inevitably accompany the layers, status, significance and value of the contents; thus it makes more sense, when the reading and writing methods in digital contents are approached as new pop culture phenomenon. This is the "The prose of everyday life", based on pop culture and "The society of Conversation", based on communication; proposed 'Digitelling' ; this is the reason why we should pay attention to the digital contents, created infinitely by the citizens of the world, as new mass-culture phenomenon.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.8.2-8.2
• /
• 2009

구리(Cu)-인듐(In)-갈륨(Ga)-셀레늄(Se)의 4 원소 화합물 반도체인 Cu(InGa)$Se_2$ (CIGS) 태양전지 세계 최고 셀효율은 2008년 현재 19.9% 로서 박막형 태양전지 중 가장 높은 효율을 보이고 있다. 이는 다결정(폴리) 실리콘 태양전지의 20.3%와 대등한 수준이다. 이 CIGS 태양전지는 제조단가를 표준 결정형 실리콘 태양전지 대비 50% 대로 획기적으로 낮출 수 있어 가장 경쟁력이 있는 차세대 재료로 꼽히고 있다. 본 연구에서는 CIGS태양전지를 고진공 물리 증작법으로 제작하였으며 표면과 박막의 순도를 외부오염을 방지하기 위하여 후면전극, 광흡수체 및 전면전극을 동일 진공에서 제작할 수 있는 멀티 챔버 클러스터 증착 시스템을 이용하였다. 기판으로 소다라 임유리, 후면전극으로 Mo, 전면전극으로 I-ZnO/Al:ZnO 및 ITO를 이용하였다. 버퍼층으로 CdS를 chemical bath deposition (CBD)를 이용하였다. 소자는 무반사막을 사용하지 않고 Al/Ni전극 그리드를 이용하였다. 이 소자로부터 0.22 $cm^2$에서 16%의 효율을 얻었다. 각 박막층 간 계면의 분석을 전기적인 특성, ellisometry에 의한 광특성, 표면과 결정성에 대한 SEM 및 XRD의 특성을 보고한다. 또한, 대표적 화합물 반도체 박막 태양전지인 CIGS 태양전지의 기술의 현황, 학문적인 과제 및 실용화의 문제점을 발표하기로 한다.

• Journal of Powder Materials
• /
• v.14 no.4
• /
• pp.230-237
• /
• 2007

The fabrication of Fe alloy-40 wt.%TiC composite materials using spark plasma sintering process after ball-milling was studied. Raw powders to fabricate Fe alloy-TiC composite were Fe alloy, $TiH_{2}$ and activated carbon. Fe alloy powder was Distaloy AE (4%Ni-1%Cu-0.5%Mo-0.01%C-bal.%Fe) made by Hoeganes company with better toughness and lower melting point. These powders were ball-milled in horizontal attrition ball mill at a ball-to-powder weight ratio of 30 : 1. After that, these mixture powders were sintered by using spark plasma sintering apparatus for 5 min at $1200-1275^{\circ}C$ in vacuum atmosphere under $10^{-3}$ torr. DistaloyAE-40 wt.%TiC composite was directly synthesized by dehydrogenation and carburization reaction during sintering process. The phase transformation of as-milled powders and sintered materials was confirmed using X-ray diffraction (XRD) and transmission electron microscope (TEM). The density and harness materials was measured in order to confirm the densification behavior. In case of DistaloyAE-40 wt.%TiC composite retained for 5 min at $1275^{\circ}C$, it has the relative density of about 96% through the influence of rapid densification and fine TiC particle reinforced Fe-based composites materials.

• Korean Journal of Environmental Agriculture
• /
• v.34 no.1
• /
• pp.64-68
• /
• 2015

BACKGROUND: Heavy metals (Al, As, Cd, Cr, Cu, Li, Hg, Ni, Pb, and Zn) were analyzed to elucidate the impact of weir construction on their concentrations in sediments of Geum River, Korea. We also attempted to investigate the source of the heavy metals in sediments. METHODS AND RESULTS: For this study, sediments were collected from May through June in 2012. The concentrations of heavy metals except Hg were determined by inductively coupled plasma mass spectrometer, and Hg was measured by automatic mercury analyzer. More clay were accumulated in the furthest stations in the upstream direction starting from the weirs. Most of the heavy metals showed higher concentrations in the most upstream located station of Geumnam Weir. However, high concentrations were not observed in the most upstream stations of the other weirs. The concentrations of Hg and As were much higher in sediments of Gap Stream. CONCLUSION: Gap Stream may be a potential source for high deposits of As and Hg. Presence of the dams may not play an important role in controlling heavy metal concentrations in sediments. It is necessary to monitor heavy metal concentrations for a longer time period to study the effect of environmental changes on heavy metal distribution in Geum River.