• 제목/요약/키워드: NiCr

검색결과 1,869건 처리시간 0.041초

산소 농도 제어를 통한 NiCrAl 합금 폼 표면의 침상 NiO 보호층 효과 (Effect of Needle-Like NiO Protecting Layer on NiCrAl Alloy Foam by Controlled Oxygen Concentration)

  • 이영근;신동요;안효진
    • 한국재료학회지
    • /
    • 제28권6호
    • /
    • pp.324-329
    • /
    • 2018
  • Needle-like NiO protecting layers on NiCrAl alloy foam, used as support for hydrogen production, are introduced through electroplated Ni and subsequent microwave annealing. To improve the stability of the NiCrAl alloy foam, oxygen concentration of microwave annealing to form a needle-like NiO layer with good chemical stability and corrosion resistance is controlled in a range of 20 and 50 %. As the oxygen concentration increases to 50 %, needle-like NiO forms a dense coating layer on the NiCrAl alloy foam; this layer formation can be attributed to accelerated growth of the (200) plane. In addition, the increased oxygen concentration causes increased NiO/Ni ratio of the resultant coating layer on NiCrAl alloy foam due to improved rate of the oxidation reaction. As a result, the introduction of dense needle-like NiO layers formed at 50 % oxygen concentration improves the chemical stability of the NiCrAl alloy foam by protecting the direct electrochemical reaction between the electrolyte and the foam. Thus, needle-like NiO can be proposed as a superb protecting layer to improve the chemical stability of NiCrAl alloy form.

Processing and Mechanical Properties of Ni-Cr and Ni-Cr-Al Foams by Pack-Cementation

  • ;최희만
    • 한국재료학회:학술대회논문집
    • /
    • 한국재료학회 2009년도 추계학술발표대회
    • /
    • pp.19.1-19.1
    • /
    • 2009
  • Open-cell Ni-Cr and Ni-Cr-Al(with gamma/gamma prime microstructure typical of Bi-base super alloys) foams are manufactured by pack-cementation at $1000{\boxplus}$degrees C, followed by homogenization at $1200{\boxplus}C$. The resulting alloyed foams retain the low relative densities (less than 3.5 wt.%). The oxidation behavior of Ni-Cr foams turns out to be identical to that of bulk Ni-Cr alloys, after taking into account the foam's higher surface area. The room-temperature compressive behavior of the Ni-Cr and Ni-Cr-Al is compared to model predictions. Additionally, the foam creep behavior, measured between 680 and $825{\boxplus}C$ in the stress range of 0.1-0.3 MPa, compared to two analytical models, namely strut compression and strut bending as high-temperature deformation modes.

  • PDF

전산모사를 활용한 Fe-Cr-Ni 전주용 수용액의 안정성 분석 (Computational Analysis of Aqueous Solution Stability for Electroformed Fe-Cr-Ni Thin Layer)

  • 전승환;한상선;김마로;최용;이상범
    • 한국표면공학회:학술대회논문집
    • /
    • 한국표면공학회 2014년도 추계학술대회 논문집
    • /
    • pp.214-214
    • /
    • 2014
  • Computational analysis of aqueous solution stability of Fe-Cr-Ni system to find an electroplating condition of Fe-Cr-Ni layer. Aqueous sulfate solution with iron, chromium and nickel ions was selected by using a numerical S/W with which aqueous solution stability was analyzed. Several possible conditions to perform electro-forming of Fe-Cr-Ni were selected with thermo-dynamical data. The Fe-Cr-Ni system was electro-formed which composition and microstructure of the electroplated Fe-Cr-Ni significantly depended on the solution temperature and electro-potential. The final composition of Fe-3%Cr-48%Ni with less than $30{\mu}m$ thick was well electroplated.

  • PDF

NiCrAlY/ZrO$_2$-Y$_2$O$_3$ 복합코팅의 산화에 따른 조직관찰 (Microstructural Changes of NiCrAlY/ZrO$_2$-Y$_2$O$_3$ Composite Coatings By Oxidation)

  • 박기범;박진오;이동복
    • 한국표면공학회지
    • /
    • 제35권2호
    • /
    • pp.101-106
    • /
    • 2002
  • The microstructural changes of $NiCrAlY/ZrO_2$-$Y_2$$O_3$ composite coatings that were manufactured by air-plasma-spraying were investigated using XRD and SEM/EDS. The as-sprayed microstructure consisted of (Ni,Cr)-rich regions, ($ZrO_2$-$Y_2$$O_3$)-rich regions, and $Al_2$$O_3$-rich layers that were formed during spraying owing to the oxidation of Al in NiCrAlY. During oxidation between 900 and $1100^{\circ}C$ in air, Cr in the (Ni,Cr)-rich regions diffused toward the $Al_2$$O_3$-rich layers, and oxidized to be dissolved in $A1_2$$O_3$-rich layers. The oxidation of Ni in the (Ni,Cr)-rich regions was less distinct, except at the outer surface of the coating.

The Electrochemical Behavior of Ni-base Metallic Glasses Containing Cr in H2SO4 Solutions

  • Arab, Sanaa.T.;Emran, Khadijah.M.;Al-Turaif, Hamad A.
    • 대한화학회지
    • /
    • 제56권4호
    • /
    • pp.448-458
    • /
    • 2012
  • In order to develop alloy resistance in aggressive sulphat ion, the corrosion behavior of metallic glasses $Ni_{92{\cdot}3}Si_{4.5}B_{32}$, $Ni_{82,3}Cr_7Fe_3Si_{4.5}B_{3.2}$ and $Ni_{75.5}Cr_{13}Fe_{4.2}Si_{4.5}B_{2.8}$ (at %) at different concentrations of $H_2SO_4$ solutions was examined by electrochemical methods and Scanning Electron Microscope (SEM) and X-ray Photoelectron Microscopy (XPS) analyses. The corrosion kinetics and passivation behavior was studied. A direct proportion was observed between the corrosion rate and acid concentration in the case of $Ni_{92{\cdot}3}Si_{4.5}B_{32}$ and $Ni_{75.5}Cr_{13}Fe_{4.2}Si_{4.5}B_{2.8}$ alloys. Critical concentration was observed in the case of $Ni_{82,3}Cr_7Fe_3Si_{4.5}B_{3.2}$ alloy. The influence of the alloying element is reflected in the increasing resistance of the protective film. XPS analysis confirms that the protection film on the $Ni_{92{\cdot}3}Si_{4.5}B_{32}$ alloy was NiS which is less protective than that formed on Cr containing alloys. The corrosion rate of $Ni_{82,3}Cr_7Fe_3Si_{4.5}B_{3.2}$ and $Ni_{75.5}Cr_{13}Fe_{4.2}Si_{4.5}B_{2.8}$. alloys containing 7% and 13% Cr are $7.90-26.1{\times}10^{-3}$ mm/y which is lower about 43-54 times of the alloy $Ni_{92{\cdot}3}Si_{4.5}B_{32}$ (free of Cr). The high resistance of $Ni_{75.5}Cr_{13}Fe_{4.2}Si_{4.5}B_{2.8}$ alloy at the very aggressive media may due to thicker passive film of $Cr_2O_3$ which hydrated to hydrated chromium oxyhydroxide.

12Cr강의 피로특성에 미치는 Ni+Mo 첨가의 영향 (Effect of Ni and Mo Addition on Fatique Property in 12Cr Steel)

  • 이진경;배동수
    • 한국산업융합학회 논문집
    • /
    • 제24권4_2호
    • /
    • pp.435-441
    • /
    • 2021
  • This research was performed to study the effect of the Ni + Mo addition on the fatigue properties in 12Cr steel. After heat treatment of 12Cr steel and 12Cr-Ni-Mo steel, tensile tests, impact tests, hardness tests, and rotary bending fatigue tests were performed, respectively. The fatigue fracture surface was observed and analyzed using SEM and EDS. The fatigue limit of 12Cr steel was 554 MPa, which was 49 MPa higher than 505 MPa of 12Cr-Ni-Mo steel. Striations, which are the shape of the typical fatigue fracture surface, were observed at the fracture surface near the starting point of fatigue fracture in the 12Cr steel and 12Cr-Ni-Mo steel. However, unlike the case of 12Cr steel, 12Cr-Ni-Mo steel also had a mixed fracture surface with the fatigue and the ductile fracture surface. When brittle non-metallic inclusions exist near the starting point of fatigue failure, the crack propagation was further promoted and the fatigue life was drastically reduced.

다공질 Ni 및 Ni-Cr으로 강화한 AC4C 복합재료의 제조 및 특성연구 (A Study for Characteristic and Manufacturing of Porous Ni/AC4C and Ni-Cr/AC4C Composites)

  • 김용현;김억수;여인동;이광학
    • 한국주조공학회지
    • /
    • 제20권1호
    • /
    • pp.21-28
    • /
    • 2000
  • Ni and Ni-Cr porous metals which are estimated to be easy to fabricate by squeeze casting are used as strengtheners for composite materials. As a matrix material, Al-7%wtSi-0.3 wt%Mg(AC4C) has been used. In case of Ni/AC4C and Ni-Cr/AC4C composite, $750^{\circ}C$ melt temperature and minimum 25 MPa squeezing pressure are needed to produce sound composite materials. The observation of interfacial reaction zone at various heat treatment condition showed that solutionizing temperature of above 520^{\circ}C$, the interfacial reaction zone increased proportionally with increasing heat treatment tim and reaction products formed by interfacial reaction are mainly composed of $Al_3Ni$ and $Al_3Ni_2$ phases. The tensile strength of Ni/AC4C and Ni-Cr/AC4C composite is lower than the matrix metal and this can be explained by the brittle intermetallic compounds formed at the interface of Ni and Ni-Cr reinforcements. But the properies of hardness, wear resistance and thermal expansion are better than the matrix due to the strengthening effect of Ni-Cr porous metals.

  • PDF

토양중(土壤中)에 있어서 무우와 배추의 생육(生育)에 미치는 중금속(重金屬) Cr, Ni, Cd, Cu, Zn의 영향(影響) (Effects of Heavy Metals Cr, Ni, Cd, Cu, Zn on Growth of Radish and Chinese Cabbage in Soils)

  • 문영희;김용휘;양환승
    • 한국환경농학회지
    • /
    • 제9권2호
    • /
    • pp.113-119
    • /
    • 1990
  • 토양중(土壤中) Cr, Ni, Cd, Cu, Zn을 각각(各各) 0, 20, 50, 100, 200ppm첨가(添加)하고 무와 배추의 발아(發芽) 및 생육(生育)에 미치는 각(各) 중금속(重金屬)의 영향(影響)을 조사(調査)하였다. 무우와 배추의 발아(發芽)는 Ni와 Cr 200ppm첨가(添加) 토양(土壤)에서 심한 억제(抑制)를 받았으나 Cu, Cd, Zn 200 ppm첨가(添加) 토양(土壤)에서는 크게 영향(影響)을 받지 않았다. 5종(種)의 중금속(重金屬)이 무우와 배추의 생육(生育) 억제(抑制)에 미치는 영향(影響)은 Cr>Ni>Cd>Cu>Zn순(順)였으며 무우보다 배추가 더 크게 억제(抑制)를 받았다. 무우에 대하여 50%이상(以上) 심한 생육억제(生育抑制)를 보였던 각 중금속(重金屬)의 첨가농도(添加濃度) Cr가 20ppm, Ni, Cd과 Cu은 50ppm, Zn은 200ppm였으며, 배추에 대하여 Cr, Ni, Cd, Cu가 20ppm, Zn은 200ppm였다. 중금속(重金屬)에 의한 2가지 작물(作物)의 생육억제(生育抑制)는 토양중(土壤中) 퇴비(堆肥)와 석회(石灰)의 첨가(添加)에 의하여 현저(顯著)히 경감(輕減)되었다.

  • PDF