• Journal of the Korean Vacuum Society
• /
• v.16 no.2
• /
• pp.116-121
• /
• 2007

TiNi shape memory alloy(SMA) was fabricated by PLD(plused laser deposition) using equiatomic TiNi target. Composition and crystallization of TiNi thin films which were fabricated in ambient Ar gas(200m Torr)and vacuum($5{\times}10^{-6}\;Torr$) were investigated. Composition of TiNi thin films was characterized by energy-dispersive X-ray spectrometry (EDXS) and crystallization was confirmed by X-ray diffraction (XRD). The composition of films depends on the distance between target and substrate but does not sensitively depend on the substrate temperature. It is found that the composition of films can be easily controlled when substrate is placed inside plume in ambient Ar gas. It is also found that the in situ crystallization temperature ($ca.\;400^{\circ}C$) in ambient Ar gas is lowered in comparison with that of TiNi film prepared under vacuum. The low crystallization temperature in ambient Ar gas makes it possible to prepare the crystalline TiNi thin film without contamination.

• The korean journal of orthodontics
• /
• v.25 no.2 s.49
• /
• pp.187-200
• /
• 1995

To estimate the characteristics of Korean Ni-Ti alloy orthodontic wire, this study investigated compositions, tensile properties, bending properties, heat treatment effects, and ion releasing degrees, and compared these characteristics to those of the imported Ni-Ti alloy wire. The results obtained are as follows ; 1. Ti and -Ni elements in ORTHOLLOY were in a range showing superelasticity, and there was a little difference in the Ni and Ti contents of ORTHOLLOY as compared with those of SENTALLOY. 2. The results of the tensile test concerning ORTHOLLOY exhibited a superelastic effect, indicating an area of a definite amount of stress in spite of the changes in the range from $2\%\;to\;8\%$ in the strain rate. 3. ORTHOLLOY presented higher load values than SENTALLOY in the same deflection values when the wire was tested in three-point bending. A load range displaying a superelastic effect was 80-l00g, 140-l80g, and 130-200g respectively, in wire diameters of 0.014', 0.016', and 0.018' 4. By heat treatments at $400^{\circ}C$ and at $500^{\circ}C$, a load range showing the effect of superelasticitly was lessened by the duration of the heat treatment time. The superelastic effect was destroyed as a result of the 10 minutes heat treatment at $600^{\circ}C$. 5. The quantity of the Ni ion released from ORTHOLLOY, tended to be greater than the amount of released Ni ion in SENTALLOY. The Co ion released was very little(<0.01ppm) in SENTALLOY and ORTHOLLOY irrespective of the lapse of time. Released Ni ions on the 1st day were at the maximum, and the releasing rate showed plateaus after three days. 6. The surface morphology of SENTALLOY was relatively regular irrespective of the lapse of rime, and the corrosion tendency was not observed. However, the surface morphology of ORTHOLLOY was rather irregular and shelved fitting corrosion after immersion.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.320-325
• /
• 2000

This study was performed to investigate the electro-chemical-machining (ECM) characteristic of Ni-Ti Shape Memory Alloy (SMA). From the experimental results, we could gain optimal electro-chemical conditions to bound with lesser machining effect and better surface roughness than any other machining methods to workpiece at the same time. At these conditions, current efficiency was, for especially ECM working of Ni-Ti SMA, approximately 100% and high frequency pulse current was detected.

• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.3
• /
• pp.197-203
• /
• 2002

The main emphasis of this study was to find an new hydrogen absorbing alloy such as Mg-Ti-Ni-H systems, and to investigate their hydrogenation properties. ($Mg_9Ti_x$)-10, 20wt%Ni-Hx systems were prepared by hydrogen induced mechanical alloying(HIMA) using Mg and Ni chips and sponge Ti. The particles synthesized were characterized by X-ray diffraction, and their morphologies were observed by means of scanning electron microscopy(SEM) with energy dispersive spectrometry (EDS). In addition, the crystal structures were analyzed in terms of their bright-/ dark field images and the selected area diffraction pattern(SADP) of transmission electron microscopy(TEM).

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.667-672
• /
• 2005

In order to effectively utilize visible light in the photocatalytic reaction, nanaocomposite of Ni doped $TiO_2$ and $NiTiO_3$ powders were synthesized by mechanical alloying and heat treatment. About 5.4 wt% of $NiTiO_3$ with particle size less than 15nm was uniformly formed in the Ni-doped rutile $TiO_2$ matrix. The UV/VIS-DRS and PL investigation showed that the nanocompasite $TiO_2$ powders had a longer absorpt ion wavelength (600$\sim$650nm, 2.0$\sim$1.9eV) than that of Ni-doped $TiO_2$ or rutile $TiO_2$ powder. The carbon decomposition of 4-CP by the nanocompasite $TiO_2$ powders were higher than other $TiO_2$ (P-25).

• Membrane Journal
• /
• v.34 no.2
• /
• pp.146-153
• /
• 2024

In this experiment, a Ti-based flat hydrogen separation membrane was designed and manufactured. In order to find a Ti-based hydrogen separation membrane of a new composition, the correlation between the physical-chemical properties and hydrogen permeability of various alloys was investigated. Based on this, two types of new alloy films (Ti_14.2Zr_66.4Ni_12.6Cu_6.8 (70 ㎛), Ti_17.3Zr_62.7Ni₂₀ (80 ㎛)) was designed and manufactured. The manufactured flat hydrogen separation membrane was tested for hydrogen permeation using mixed gas (H₂, N₂) and sweep gas (Ar) at 300~500℃ and 1~4 bar. The Ti_14.2Zr_66.4Ni_12.6Cu_6.8 alloy film has a maximum flux of 16.35 mL/cm² min at 500℃ and 4 bar, and the Ti_17.3Zr_62.7Ni₂₀ alloy film has a maximum flux of 10.28 mL/cm² min at 450℃ and 4 bar.

• Proceedings of the KWS Conference
• /
• 1994.10a
• /
• pp.163-165
• /
• 1994

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.1
• /
• pp.45-52
• /
• 2002

It has been known that tensile residual stresses occurring by the thermal expansion coefficient mismatch between fiber and matrix is a cause of the weak strength of metal matrix composites(MMCs). In order to solve this problem, TiNi alloy fiber was used as a reinforced material in TiNi/A16001 shape memory alloy composite in this study. TiNi alloy fiber improves the tensile strength of the composite by causing compressive residual stress in matrix on the basis of its shape memory effect. Pre-strain was imposed to generate the compressive residual stresses inside the TiNi/A16001 shape memory alloy composites. AE technique was used to quantify the microscopic damage behavior of the composite at high temperature. The effect of applied pre-strains on the AE behavior was also evaluated.

• Transactions of the Korean hydrogen and new energy society
• /
• v.10 no.4
• /
• pp.211-217
• /
• 1999

In order to investigate the possibilities of microbatteries using TiNi type metal hydride, TiNi films were prepared by DC magnetron sputtering. The films were deposited under various Ar flow rates, DC powers and target-to-substrate distances to find the optimum sputtering conditions. The deposition rate of TiNi thin film increased by increasing the DC power and by decreasing the Ar flow rate and target-to-substrate distance. The chemical composition of the film changed as a target-to-substrate distance. The crystal structure of the film was amorphous state just after deposition and changed to crystalline by vacuum heat treatment.

• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.4
• /
• pp.135-141
• /
• 1998

The effects of heat-treatment on discharge characteristics of $TiFe_{1-x}Ni_x$ alloy were investigated. The content of Ni in alloy was varied from x = 0.1 to 0.6 by each 0.1 increment. Discharge capacity change of each alloy with C/D cycles was measured. With increasing Ni-content initial discharge capacity was increased. but at x = 0.6 it was deceased again. With increasing C/D cycles discharge capacity was rapidly decreased in the alloy of high Ni-content. In order to investigate the effects of heat-treatment on cycle life, $TiFe_{0.5}Ni_{0.5}$ alloy having maximum initial discharge capacity was heat-treated at various temperatures in the range of $700{\sim}900^{\circ}C$ and tested. The loss of initial discharge capacity was appeared at all temperatures. but cycle characteristics of the alloy was improved. The electrodes heat-treated for 1 hour in the range of $700{\sim}850^{\circ}C$ showed good recovery of discharge capacities through repeated cycles, and from SEM observation results these were considered as 1 hour in the range of $700{\sim}850^{\circ}C$ showed good recovery of discharge capacities through repeated cycles, and from SEM observation results these were considered asbeing due to increased electrode strength and small loss of porosity during heat-treatment. The electrode heat-treated for 1 hour at $900^{\circ}C$ showed poor discharge characteristics because of low porosity.