• Journal of Navigation and Port Research
• /
• v.39 no.4
• /
• pp.335-344
• /
• 2015

This study aims to assess the effectiveness of zeolite, montmorillonite, and steel slag as capping materials to block the release of heavy metals from marine sediment depending on their depths. The results showed that all capping materials used this study were not effective in interrupting release of As. Zeolite had negative effect on the block of Cr release but it was significantly reduced to 5 cm by montmorillonite capping. In contrast to As and Cr, Cd, Ni, and Pb were not released even from uncapped sediments. Cu and Zn were the heavy metals those were most significantly influenced by the capping conditions. Cu release from marine sediments were effectively blocked by more than 1 cm depth of montmorillonite and more than 3 cm depth of zeolite. All capping materials were found to be effective in interrupting release of Zn from marine sediments. It was concluded that the zeolite, montmorillonite, and steel slag could be used as a potential capping material for interrupting the release of Cr, Cu, and Zn from the contaminated marine sediments.

• Journal of the Korean Society for Heat Treatment
• /
• v.20 no.6
• /
• pp.323-328
• /
• 2007

This study has been investigated the effect of high temperature gas nitriding (HTGN) heat treatment of STS 444 (18Cr-0.01Ni-0.01C-0.2Nb) ferritic stainless steel in an atmosphere of nitrogen gas at the temperature range between $1050^{\circ}C\;and\;1150^{\circ}C$. The surface layer was changed into martensite and austenite with the nitrides of NbCrN by HTGN treatment. Due to the precipitation of nitrides and matrensite formation, the hardness of the surface layer showed $400Hv{\sim}530Hv$. The nitrogen concentration of the surface layer appeared as 0.05%, 0.12% and 0.92%, respectively, at $1050^{\circ}C,\;1100^{\circ}C\;and\;1150^{\circ}C$. When the nitrogen is permeated from surface to interior, Nb and Cr, which have strong affinities with nitrogen, also move from interior to surface. Therefore it is considered that this counter-current of atoms promotes the formation of NbCrN at the surface layer.

• Journal of the Korean earth science society
• /
• v.24 no.8
• /
• pp.711-720
• /
• 2003

To study characteristics of the heavy metal pollution, sediment samples were collected at 67 sites on the roadside of Jeonju city during summer and winter, 2002. The total concentration of metals including Cd, Co, Cr, Cu, Ni, Pb, Zn, and Mn in the sediment samples were determined. The results indicate that the roadside sediments in Jeonju city have lower (1/2 to 1/7 times) concentrations of Zn, Cu, Pb and Cd than the metal concentrations previously reported for roadside soil, dust and sewage sludges in Seoul. However, the metal concentrations are higher than environmental quality criteria in soil suggested from several countries, and Zn, Cu, Pb and Cd contents are usually 2-7 times higher than the world average contents of the metals in natural soil. Although pollution index and concentrations of Cr, Ni, Pb and Zn in the roadside sediments at industrial area were usually higher than those of downtown and residential area, the metal having small vehicle- and steel-related industries had high concentrations of metals. The results of chemical partitioning analysis showed that Pb, Zn and Mn are mainly associated with carbonate/adsorbed and Fe-Mn oxide phases but that Cu is largely associated with the organic and sulfide fractions. It thus indicates that both large and small (vehicle- and steel-related) industries are main sources of heavy metal contamination. Due to high solubility of the carbonate phases by natural leaching episodes, the carbonate/adsorbed Cd, Co, Ni, Pb, Zn and Mn in the roadside sediments may serve as a potential source of contamination.

• Korean Journal of Materials Research
• /
• v.7 no.2
• /
• pp.162-170
• /
• 1997

This study has evaluated the dissimialr weldability of Incoloy 825 Ni base alloy with a mild steel(SS41). Further a compatibility study of wrveral Ni base filler metals with the dissimilar joint between the two alloys was also included. The dissimilar weldability of Incoloy 825 with mild steel is strongly dependent upon the type of the filler metal used. Among the filler metals, ENiCrFe which has a chemical comosition similar to that of Incoloy 825 was found to be most compatible to the joint. In addition, a filler metal which showed a good cracing resistance in one dissimiar alloy combination was not necessarily graranteed to other combination. Microstructural examination with SEM, TEM and Auger revealed that the solidification cracking resestance of the dissimilar joint. between Incoloy 835 and SS41 was closely with the Ti+Nb content and with the content of a low melting eutectic phase of Laves relatibve to that of MC type phase.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1993.11a
• /
• pp.4-4
• /
• 1993

Ferrous powder metallurgy in Japan has developed in the last four decades, where every decade is featured by certain breakthroughs in materials. The progress in PM materials is closely related to newly developed powders. Low alloy steel powders for high strength PM components are grouped into three types: Ni and/or Mo containing completely alloyed powders, Ni containing partially alloyed powders, and Cr containing completely alloyed powders. Every type has its special characteristics. The tensile strength of PM materials is improved up to 2 GPa. The hardness is also increased to exceed 500 HV with normal hardening methods, and 700 HV with novel surface treatment techniques. The present maximum of fatigue strength is 550 MPa, and that of impact energy is 100 J. Novel PM materials with improved properties are applied to a variety of automobile and other components: power steering pumps, rocker anns, valve guides and inserts, bearings, torque sensors, etc. The future outlook for the ferrous PM is Quite positive, and the industry is expected to show renewed growth by applying many types of alloy steel powders and new ferrous PM materials.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.3
• /
• pp.192-199
• /
• 1998

This study was carried out to investigate the influence of variations in the temperature and time of isothermal heat treatment, applied stresses and prestrain on the isothermal transformation behavior of ${\gamma}$ and ${\sigma}$ phases and mechanical properties of 25Cr-7Ni-3Mo duplex stainless steel. The precipitation of ${\gamma}$ and ${\sigma}$ phases through isothermal heat treatment showed the type curves with a certain incubation period, the curve migrated to in a short period of time and the amount of precipitation increased with decreasing isothermal heat treatment temperature. Under the state of isothermal transformation, the precipitation of ${\gamma}$ and ${\sigma}$ phases was stimulated by applied stress, with increasing applied stress, the curves migrated to in a short period of time and also observed that the application of stress has a greater influence on the amount of ${\sigma}$ precipitation than that of ${\gamma}$ precipitation. The precipitation of ${\gamma}$ and ${\sigma}$ phases was stimulated by cold and warm rolling before isothermal heat treatment and precipitation of ${\gamma}$ and ${\sigma}$ phases has a greater influence on the warm rolling than cold rolling. The tensile strength and hardness increased with increasing cold and warm rooling reduction ratio.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.56-56
• /
• 2009

AISI 316L 스테인리스강에 새롭게 디자인한 서로 다른 3가지 응고모드를 가진 와이어로 FCAW(Flux Cored Arc Welding)을 하였다. 각각의 3가지 와이어는 Pseudobinary phase diagram에 따라 AF, FA, F모드를 가졌다. 미세조직은 $Cr_{eq}/Ni_{eq}$이 증가할수록 델타 페라이트 함량이 증가하였으며, 초정 상의 경우 초정 오스테나이트에서 초정 페라이트로 변태하였고, 연성저하균열의 민감도가 감소하였다. 연성저하균열은 이동결정립계의 형상에 따라 좌우되며, 미량의 페라이트를 함유한 오스테나이트에서는 페라이트가 핀(Pin) 역할을 제대로 하지 못하여 직선형태의 이동 결정립계 따라 입계 미끄러짐의 메커니즘을 통해 전파되었으며, 곡선형태의 이동 결정립계에서는 델타 페라이트가 핀 역할을 하여 역할을 하여 구속 상태에서 응력집중을 막고 응력을 분산시켜 균열이 전파되는 것을 방해하여 균열이 발생되지 않았다.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.2
• /
• pp.75-79
• /
• 2013

This study was carried out to investigate the precipitation behavior of the ${\chi}$ phase and the impact toughness of 25%Cr-7%Ni-2%Mo-4%W super duplex stainless steel. The ${\chi}$ phase was precipitated in the early stage of aging, and with the increasing aging time. However, after reaching a maximum value, the number decreased as a result of the gradual transformation of the ${\chi}$ phase into the ${\sigma}$-phase. It was proved that the ${\chi}$ phase was an intermetallic compound, which represented a lower nickel concentration, higher chromium and molybdenum concentrations, and very higher tungsten concentration compared to the matrix phases. It also showed higher molybdenum and tungsten concentrations than the ${\sigma}$ phase. The decomposition of the ferrite phase into the ${\gamma}_2$ and ${\sigma}$ phases was retarded by W substitution for Mo. Thus, the number of ${\chi}$ phases increased. The impact value was decreased by the substitution of W for Mo. The impact toughness rapidly decreased with time when the ${\chi}$ phase began to precipitate in the initial stage of aging. The impact toughness was, therefore, greatly influenced for the precipitation of the ${\chi}$ phase.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.341-342
• /
• 2008

• Journal of Environmental Science International
• /
• v.5 no.4
• /
• pp.463-471
• /
• 1996

In order to investigate the characteristics of dustfall at eight sites in Pusan, the dustfal1 samples were collected with dust jar method from May to September 1995, and Cr, Mn, Fe, Ni, Cu, Zn, Cd and Pb were analyzed, The main results of this study are summarized as follows; 1) The total mean value of dustfall was 11.30 ton/$^{\circ}C$/month. 2) The maximum and minimum values of dustfall were industrial and resident area respectively, 3) The dustfall showed the general trend in order as May>Jun>September>July. 4) The general trend of the heavymetals in dustfall was in order as Fe>Cu>Zn>Pb>Ni>Cd>Cr>Mn any the concentrations of heavymetals had different tendencies according to sources of Pollutant meterials. 5) The Concentrations of Fe, Cu, Pb, Ni, Cd and Cr in industrial area and Mn, Pb and Zn in traffic area were high. The concentrations of heavymetals in residence area and unpolluted area were generally low. 6) Cr, Cu and Cd were influenced by the steel industry and the metal products plant and Zn was influenced by the automobiles. Mn, Fe and Ni were influenced by the soil as wet as artificial outlet. 7) The correlation between the total amount of dustfall and the concentrations of the heavymetals by month was high and the correlation between the heavymetals of the same origin was high.