• Journal of the Korean Electrochemical Society
• /
• v.12 no.3
• /
• pp.258-262
• /
• 2009

The composition and semiconducting properties of the passive films formed on Ni- (15, 30)Cr-5Mo alloys in pH 8.5 buffer solution were examined. The depth concentration profile of passive films formed on Ni-(15, 30)Cr-5Mo in pH 8.5 buffer solution showed that Mo enhances the enrichment of Cr. The Mott-Schottky plot for the passive film on Ni-(15, 30)Cr- 5Mo closely resembled that for the film on Cr, whereas those for the less Cr-enriched film on Mo-free alloys showed similar behavior to that for the film on Ni. The acceptor density was reduced by increasing Cr content in Ni-(15, 30)Cr-(0, 5)Mo alloys, but addition of Mo considerably increased the acceptor density.

• Journal of the Korean Ceramic Society
• /
• v.43 no.11 s.294
• /
• pp.746-750
• /
• 2006

NiO films and Ru co-sputtered NiO films were deposited by reactive magnetron sputtering for micro-solid oxide fuel cell anode applications. The deposited films were reduced to form porous films. The reduction kinetics of the Ru doped NiO film was more sluggish than that of the NiO film, and the resulting microstructure of the former exhibited finer pore networks. The possibility of using the films for the anodes of single chamber micro-SOFCs was investigated using an air/fuel mixed environment. It was found that the abrupt increase in the resistance is suppressed in the Ru co-sputtered film, as compared to undoped film.

• Electrical & Electronic Materials
• /
• v.10 no.9
• /
• pp.938-944
• /
• 1997

Cu-Ni thin film strain gauges for diaphragm-type pressure sensors were developed. Thin films of Cu-Ni alloys of various compositions were deposited onto glass and stainless steel substrates by RF magnetron sputtering. The effects of composition substrate temperature Ar partial pressure and aging on the electrical properties of Cu-Ni film strain gauges in the thickness range 500~2000$\AA$ are discussed. The maximum resistivity(95.6 $\mu$$\Omega$cm) is obtained from 53wt%Cu-47wt%Ni films while the temperature coefficient of resistance(TCR) becomes minimum(25.6ppm/$^{\circ}C$). The gauge factor is about 1.9.

• Journal of the Korean Ceramic Society
• /
• v.41 no.2
• /
• pp.106-110
• /
• 2004

Nickel oxide (NiO) thin films were prepared on Si(100) substrates at room temperature by RF magnetron sputtering using a NiO target. The effects of oxygen flow ratio for the plasma gas on the preferred orientation and surface morphology of the NiO films were investigated. Highly crystalline NiO film with (100) orientation was obtained when it was deposited in pure Ar gas. For NiO film deposited in pure O$_2$ gas, on the other hand, the orientation of the film changed from (100) to (111) and its deposition rate decreased. The origin of the preferred orientation of the films was discussed. NiO films also showed different surface morphologies and roughnesses with the oxygen flow ratio.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.357-360
• /
• 2019

We demonstrate an alignment technology using an imprinting process on an inorganic NiOx film. The aligned nanopattern was fabricated on a silicon wafer by laser interference lithography. The aligned nano pattern was then imprinted onto the sol-gel driven NiOx film using an imprinting process at an annealing temperature of $150^{\circ}C$. After the imprinting process, parallel grooves had been formed on the NiOx film. Atomic force microscopy and water contact angle measurements were performed to confirm the parallel groove on the NiOx film. The grooves caused liquid crystal alignment through geometric restriction, similar to grooves formed by the rubbing process on polyimide. The liquid crystal cell exhibited a pretilt angle of $0.2^{\circ}$, which demonstrated homogeneous alignment.

• Journal of the Korean institute of surface engineering
• /
• v.55 no.4
• /
• pp.202-214
• /
• 2022

Internal connections between device, package and external terminals for connecting packaging and printed circuit board are normally manufactured by electroless Ni-P plating followed by immersion Au plating (ENIG process) to ensure the connection reliability. In this study, a new non-cyanide-based immersion and electroless Au plating solutions using thiomalic acid as a complexing agent and aminoethanethiol as a reducing agent was investigated on different underlayer electroless Ni-P plating layers. As a result, it was confirmed that the deposition behavior and film properties of electroless Au plating are affected by grain size and impurity of the electroless Ni-P film, which is used as the plating underlayer. Au plating on the electroless Ni-P plating film with a dense surface structure showed the highest bonding strength. In addition, the electroless Au plating film on the Ni-P plating film has a smaller particle size exhibited higher bonding strength than that on the large particle size.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.3 s.32
• /
• pp.37-45
• /
• 2004

Electroless Ni(P) has been widely used for under bump metallization (UBM) of flip chip and surface finish layer in microelectronic packaging because of its excellent solderability, corrosion resistance, uniformity, selective deposition without photo-lithography, and also good diffusion barrier. However, the brittle fracture at solder joints and the spatting of intermetallic compound (IMC) associated with electroless Ni(P) are critical issues for its successful applications. In the present study, the mechanism of IMC spatting and microstructure change of the Ni(P) film were investigated with varying P content in the Ni(P) film (4.6,9, and $13 wt.\%$P). A reaction between Sn penetrated through the channels among $Ni_3Sn_4$ IMCs and the P-rich layer ($Ni_3P$) of the Ni(P) film formed a $Ni_3SnP$ layer. Thickening of the $Ni_3SnP$ layer led to $Ni_3Sn_4$ spatting. After $Ni_3Sn_4$ spatting, the Ni(P) film directly contacted the molten solder and the $Ni_3P$ phase further transformed into a $Ni_2P$ phase. During the crystallization process, some cracks formed in the Ni(P) film to release tensile stress accumulated from volume shrinkage of the film.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.1
• /
• pp.1-8
• /
• 2020

Sulfamate-chloride baths were fabricated to study the properties of the electrodeposited Ni and NiCo thin films. The dependences of current efficiency, deposit composition of Ni and Co, residual stress, surface morphology and microstructure of electrodeposited Ni and NiCo thin films on CoCl₂ concentration in sulfamate-chloride baths were investigated. The current efficiency was measured to be more than about 90%, independent of the changes of CoCl₂ concentration in the baths. Residual stress of Ni and NiCo thin films was increased from about 45 to about 250 MPa with varying CoCl₂ concentration from 0 to 0.210 M CoCl₂ in the baths and then reached to a plateau, about 250 MPa above 0.420 M CoCl₂ concentration. Nodular surface morphologies were observed at most CoCl₂ concentrations in the baths except 0.210 M. NiCo thin film electrodeposited from the bath with 0.210 M CoCl₂ concentration showed an acicular surface morphology. Pure Ni thin film consists of FCC(111), FCC(200), FCC(220), and FCC(311) peaks without any preferred orientation. On the other hand NiCo thin films make up of HCP(100), FCC(111), HCP(101), FCC(200), FCC(220) or HCP(110), FCC(311) or HCP(112) and FCC(222) peaks. It was revealed from the analysis of XRD result that FCC(111) peak at the NiCo thin film electrodeposited from the bath with 0.084 M CoCl₂ concentration can be regarded as the preferred orientation. However the peak of the preferred orientation was changed to FCC(220) or HCP(110) above 0.084 M CoCl₂ concentration in the baths. Then the intensity of FCC(220) or HCP(110) peak was gradually decreased with increasing CoCl₂ concentration further. The crystalline size of pure Ni thin film was observed to be about 53 ㎛ and those of NiCo thin films were in the range of 35~45 ㎛.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.205-206
• /
• 2011

Cu thin films for electromagnetic wave shielding were prepared on PET film and Ni-coated PET film by using Dry and Wet coating method, such as evaporation method, DC sputtering method and copper sulfate($CuSO_4$). After that, Zn thin film and Ni thin film were prepared onto the Cu thin films by using evaporation dry process and Ni electro plating wet process as a finishing treatment, respectively. The result of conductivity test and corrosion resistance test revealed Cu thin films which were formed with bigger grain size and high Cu composition rate have superior properties. Zn thin film by dry evaporation process and Ni thin film by wet electro plating process on Cu thin films were largely contributed to corrosion resistance. However, Ni thin film by wet process made conductivity of all specimen worse, the other hand, Zn thin film by dry process made it better to improve condictivity of specimens just prepared by dry process.

• Journal of the Korean Magnetics Society
• /
• v.11 no.4
• /
• pp.163-167
• /
• 2001

The rotation of uniaxial anisotropy field of 700 ${\AA}$ thick sputtered NiFe thin film due to magnetic annealing was investigated. NiFe film was annealed in a magnetic field which is perpendicular to the initial induced uniaxial anisotropy field. The NiFe film becomes nearly isotropic after 1 hour annealing at 160 $^{\circ}C$. With increase of annealing temperature over 160 $^{\circ}C$, the film gets uniaxial anisotropy field again. An abrupt increase of H$\sub$c/ was observed with annealing temperature over 400 $^{\circ}C$. The X-ray diffraction analysis and Auger electron spectroscopy with Ar ion etching showed extensive grain growth in NiFe film with (111) texturing and interdiffusion with adjacent Au electrode layer by 400 $^{\circ}C$ magnetic annealing.