• 제목/요약/키워드: Ni dissolution

검색결과 99건 처리시간 0.027초

고상확산접합된 Haynes230의 인장성질에 미치는 접합조건의 영향 (Effect of Bonding Condition on the Tensile Properties of Diffusion Bonded Haynes230)

  • 강길모;전애정;김홍규;홍성석;강정윤
    • Journal of Welding and Joining
    • /
    • 제31권3호
    • /
    • pp.76-83
    • /
    • 2013
  • This study investigated the effect of bonding temperature and holding time on microstructures and mechanical properties of diffusion bonded joint of Haynes230. The diffusion bonds were performed at the temperature of 950, 1050, and $1150^{\circ}C$ for holding times of 30, 60, 120 and 240 minutes at a pressure of 4MPa under high vacuum condition. The amount of non-bonded area and void observed in the bonded interface decreased with increasing bonding temperature and holding time. Cr-rich precipitates at the linear interface region restrained grain migration at $950^{\circ}C$ and $1050^{\circ}C$. However, the grain migration was observed in spite of short holding time due to the dissolution of precipitates to base metal in the interface region at $1150^{\circ}C$. Three types of the fracture surface were observed after tensile test. The region where the coalesce and migration of grain occurred much showed high fracture load because of base metal fracture whereas the region where those did less due to the precipitates demonstrated low fracture load because of interface fracture. The expected fracture load could be derived with the value of fracture area of base metal ($A_{BF}$) and interface ($A_{IF}$), $Load=201A_{BF}+153A_{IF}$. Based on this equation, strength of base metal and interface fracture were calculated as 201MPa and 153MPa, respectively.

Zr계 비정질 삽입재를 이용한 Ti-Cu 이종 접합부의 미세조직 형성에 미치는 확산 열처리 온도의 영향 (Effect of the Heat Treatment Temperature on the Brazed Microstructure of Dissimilar Ti and Cu Metals Using a Zr-Base Amorphous Filler)

  • 이정구;이종극;이민구;이창규
    • 열처리공학회지
    • /
    • 제20권1호
    • /
    • pp.17-21
    • /
    • 2007
  • In this study, brazing characteristics of the dissimilar Ti and Cu metals using a Zr-base amorphous filler ($Zr_{41.2}Ti_{13.8}Cu_{12.5}Ni_{10.0}Be_{22.5}$ in at.%) have been investigated for various bonding temperatures. In the sample brazed at $790^{\circ}C$ for 10 min., the Ti-rich phases in the joint were observed, while the Cu-rich phases were obtained in the sample brazed at $825^{\circ}C$ for 10 min.. Such a different microstructure and composition in the joints could be explained by the degree of the dissolution reaction. At $790^{\circ}C$, the reaction between the Zr-rich liquid phase and the Ti base metal was actively occurred to form Ti-rich liquid phase in the joint. As the temperature increased to $825^{\circ}C$, however, the reaction between the Ti-rich liquid phase and the Cu base metal was promoted to form the Cu-rich liquid phase in the joint finally. Such a different interface reaction is attributed to the reactivity or solubility between the Zr as a main element in the filler and the Ti and Cu as a base metal element.

원자로 내부구조물 균열개시 민감도에 미치는 영향인자 고찰 (Review of Factors Affecting IASCC Initiation of Stainless Steel in PWRs)

  • 황성식;최민재;김성우;김동진
    • Corrosion Science and Technology
    • /
    • 제20권4호
    • /
    • pp.210-229
    • /
    • 2021
  • To safely operate domestic nuclear power plants approaching the end of their design life, the material degradation management strategy of the components is important. Among studies conducted to improve the soundness of nuclear reactor components, research methods for understanding the degradation of reactor internals and preparing management strategies were surveyed. Since the IGSCC (Intergranular Stress Corrosion Cracking) initiation and propagation process is associated with metal dissolution at the crack tip, crack initiation sensitivity was decreased in the hydrogenated water with decreased crack sensitivity but occurrence of small surface cracks increased. A stress of 50 to 55% of the yield strength of the irradiated materials was required to cause IASCC (Irradiation Assisted Stress Corrosion Cracking) failure at the end of the reactor operating life. In the threshold-stress analysis, IASCC cracks were not expected to occur until the end of life at a stress of less than 62% of the investigated yield strength, and the IASCC critical dose was determined to be 4 dpa (Displacement Per Atom). The stainless steel surface oxide was composed of an internal Cr-rich spinel oxide and an external Fe and Ni-rich oxide, regardless of the dose and applied strain level.

보은제일폐탄광 주변 하천수의 지구화학적 특징 (Geochemistry of Stream Water around the Abandoned Boeun Coal Mine, Hoenam Area)

  • 전서령;신익종;이규승
    • 한국환경농학회지
    • /
    • 제20권1호
    • /
    • pp.20-27
    • /
    • 2001
  • 보은광산지역 하천수의 pH는 $6.8{\sim}8.2$로 약산성에서 약 알카리성에 걸친 수질변화를 보여주며, 건기보다는 우기의 하천수가 산성우의 영향으로 인해 다소 pH가 낮게 나타났다. 방치된 폐석 등의 영향으로 Mg, Ca, $HCO_3$, $SO_4$, Al, Fe, Zn, Ni, Co, Cr, Cd, Sr, U 이 하천수내에 부화되어 나타나며, Na, K, As, Cu, $NO_3$, Cl 등은 낮은 농도함량을 보여 이들 원소에 대해 폐광석으로부터의 영향이 거의 없는 것으로 보인다. 주요 양이온 농도는 Mg>Ca>Na>K의 순서로 함량변화를 보이며, 음이온의 함량변화는 $SO_4>HCO_3>Cl>NO_3$의 순서로 나타나 본 하천수는 $Mg-SO_4$ 타입을 보인다. 하천수의 우기와 건기의 이온의 농도변화는 ${\pm}30$ % 이내에서 나타나며, Na, K, $HCO_3$, U, Sr, Cr은 우기 중에 낮은 농도를 보여 우수에 의해 희석되어졌을 가능성이 크다. 우기중에 높은 농도를 보이는 Ca, Mg, $NO_3$, Cd, Co는 약산성의 우수에 의해 기반암이나 폐석으로부터 쉽게 용출되는 원소들이라 판단되었다. TDS, EC 및 Ca, Na, Mg, $HCO_3$, $SO_4$, Fe, Ni, Sr, U등의 원소는 광산으로부터 멀어질수록 하류를 향해 농도가 감소하는 경향을 보여, 이들 원소에 대해서 광폐석이 특히 주요한 오염원으로 작용하고 있으며, 이들 원소의 농도를 컨트롤하는 인자는 희석작용이나 흡착작용 등이 복합적으로 관여하고 있을 것으로 생각된다. 본 광산지역의 하천수내에 일어나는 화학적 현상은 크게 두 가지로 얘기할 수 있다. 철을 함유한 황화광물(황철석 등)의 산화로 인한 Fe과 $SO_4$의 하천수내에 부화현상과 풍화된 기반암에서 탄산의 용출이나 이온교환작용에 의한 중화작용으로 하천은 산성을 띠기보다 오히려 약 알카리성을 띠는 특징을 보인다. 기반암의 영향으로 하천의 지나친 산성화는 일어나지 않을 것으로 보이나 하천내의 이온함량은 비오염수에 비해 극히 높은 값을 보여 방치된 폐석이 잠재적인 위험성을 내포하고 있음을 시사한다. 또한 알카리상태에서 부화된 철은 철수산화물의 형태로 침전되어 하천의 적화현상을 일으키는 주원인 물질로 작용한다. 이들 철산화물은 침전되면서 동시에 하천내의 용존 중금속을 흡착이나 공침에 의해 동시에 침전시키는 역할을 하는 것으로 방치될 경우 2차적 오염원으로 작용할 우려가 있어, 이들 철산화물에 대한 보다 상세한 연구가 필요하다고 사려된다.

  • PDF

서태평양 마젤란해산군 OSM-XX 해저산 망간각의 광물학적, 지화학적 특성과 고해양 고환경 복원 연구 (Revealing the Paleo-ocean Environment of OSM-XX in the Western Pacific Magellan Seamount with Mineralogical and Geochemical Properties of Ferromanganese Crust )

  • 박진섭;양기호
    • 자원환경지질
    • /
    • 제56권1호
    • /
    • pp.55-63
    • /
    • 2023
  • 망간각의 지화학적, 광물학적 특성의 변화는 인근 환경 변화를 반영한다. 따라서 서태평양 마젤란해산군 OSM-XX의 망간각에 대한 특성 파악과 고해양 복원 연구를 위하여 지화학적, 광물학적 분석을 각각 micro X-ray fluorescence (μ-XRF) 과 X-ray diffraction (XRD)를 이용하여 실시하였다. OSM-XX의 망간각은 인산염화 여부 및 구조에 의해 인산염화 작용을 받은 부분(L4-L5), 인산염화 작용을 받지 않은 치밀한 부분(L3), 인산염화 작용을 받지 않은 다공성 부분(L1-L2)의 세 부분으로 구분되었다. 철망간 산화광물 층에서는 모두 버나다이트 피크가 확인되었으며, 인산염화 작용을 받은 부분은 carbonate fluorapatite(CFA)의 존재와 높은 Ca, P의 특성을 나타내었다. 인산염화 작용을 받지 않은 치밀한 부분은 높은 Mn, Ni, Co를 나타내었고, 인산염화 작용을 받지 않은 다공성 부분은 높은 Fe값과 detritus quartz, feldspar가 확인되었다. OSM-XX의 망간각이 성장하는동안 나타난 특성의 변화는 인근 해양환경의 변화를 반영하였다. 약 51.87 Ma의 연대를 나타내는 망간각의 인산염 퇴적체는 약 36-32 Ma의 전지구적 인산염화 작용에 의해 형성된 것으로 보이며, 이는 당시의 상승된 해수면 높이와 낮은 해수온을 지시한다. 또한, 치밀한 구조에서의 높은 Mn, Ni, Co, Mn/Fe 비는 강화된 산소최소층과 환원환경을 지시하며, 다공성 구조에서의 높은 Fe와 낮은 Mn/Fe 비는 약화된 산소최소층과 산화환경을 지시한다. 이는 마이오세-올리고세 경계의 Mi-1 빙하기가 끝난 후 환경변화를 반영하였다. 9 Ma부터 이어진 한랭화의 결과로 인한 저층류와 산소최소층의 강화에 의해 망간각 최외각의 Mn/Fe 비와 Co/Mn 비가 미세하게 증가하였지만, 6 Ma부터 태평양에 발생한 탄산염 용해율의 감소로 성장속도의 감소를 야기하였다.

저희석 유리구 용해법에 의한 암석시료 미량원소 분석법 (Low Dilution Glass Bead Digestion Technique for the Trace Element Analysis of Rock Samples)

  • 박찬수;신형선;오혜영;문종화;정창식
    • 암석학회지
    • /
    • 제20권3호
    • /
    • pp.161-172
    • /
    • 2011
  • 유도결합 플라즈마 질량분석법에 의한 암석 시료의 미량원소 정량분석을 위한 전처리 과정으로 통상 산분해법인 비이커-가열판 용해법이 사용된다. Zr과 Hf은 다른 비유동성 원소들과 함께 지구조 해석에 이용되는 중요한 원소이지만 암석 내에 이들을 농집시키는 불용성 광물이 있으면 비이커-가열판 용해법으로 완전히 용해되지 않는다. 이러한 불용성 광물을 용해시키기 위해 고압 테프론 용기법이나 알칼리 용융법을 이용하는데 전처리시간이 너무 오래 걸리거나 농도가 낮은 희토류원소 등의 분석 정확도가 감소하는 문제점이 있다. 이 연구에서는 자동 용융 기기를 사용하여 미국지질조사소의 암석 표준시료 3종(AGV-2, BHVO-2, G-3)을 저희석 유리구로 제작하고 이 유리구를 분말로 만들어 산분해를 거쳐 용해시킨 방법(유리구 용해법)으로 전처리한 후, 유도결합 플라즈마 질량분석기와 유도결합 플라즈마 원자방출분광기를 이용하여 희토류 원소를 포함한 30종의 미량원소 분석을 실시하였으며 시료에 대한 최종적인 희석비율은 1:2,000 이하로 유지하였다. 이 유리구 용해법에 의한 분석결과를 암석 분말시료를 이용한 비이커-가열판 용해법과 비교해 보았다. 대체적으로 Cr, Co, Ni, Cu, Zn, Pb 등의 원소분석 결과는 두 방법 모두 3종의 표준물질에서 추천치와 잘 부합되었으며 유리구 용해법을 이용한 분석에서 Pb, Zn 등 휘발성 원소의 손실은 나타나지 않았다. 저어콘을 많이 함유한 화강암 표준시료(G-3)의 Y, Zr, Hf과 중희토류원소에 대해서는 비이커-가열판 용해법의 경우 추천치에 비해 체계적으로 낮은 값을 보인 반면 유리구 용해법은 추천값에 잘 부합되는 결과를 얻었다. 이 연구의 유리구 용해법을 이용하면 불용성 원소를 포함한 미량원소 분석의 정확도가 크게 향상될 것으로 기대된다.

High Strength Nanostructured Metastable Alloys

  • Eckert, Jurgen;Bartusch, Birgit;Schurack, Frank;He, Guo;Schultz, Ludwig
    • 한국분말재료학회지
    • /
    • 제9권6호
    • /
    • pp.394-408
    • /
    • 2002
  • Nanostructured high strength metastable Al-, Mg- and Ti-based alloys containing different amorphous, quasicrystalline and nanocrystalline phases are synthesized by non-equilibrium processing techniques. Such alloys can be prepared by quenching from the melt or by powder metallurgy techniques. This paper focuses on one hand on mechanically alloyed and ball milled powders containing different volume fractions of amorphous or nano-(quasi)crystalline phases, consolidated bulk specimens and, on the other hand. on cast specimens containing different constituent phases with different length-scale. As one example. $Mg_{55}Y_{15}Cu_{30}$- based metallic glass matrix composites are produced by mechanical alloying of elemental powder mixtures containing up to 30 vol.% $Y_2O_3$ particles. The comparison with the particle-free metallic glass reveals that the nanosized second phase oxide particles do not significantly affect the glass-forming ability upon mechanical alloying despite some limited particle dissolution. A supercooled liquid region with an extension of about 50 K can be maintained in the presence of the oxides. The distinct viscosity decrease in the supercooled liquid regime allows to consolidate the powders into bulk samples by uniaxial hot pressing. The $Y_2O_3$ additions increase the mechanical strength of the composites compared to the $Mg_{55}Y_{15}Cu_{30}$ metallic glass. The second example deals with Al-Mn-Ce and Al-Cu-Fe composites with quasicrystalline particles as reinforcements, which are prepared by quenching from the melt and by powder metallurgy. $Al_{98-x}Mn_xCe_2$ (x =5,6,7) melt-spun ribbons containing a major quasicrystalline phase coexisting with an Al-matrix on a nanometer scale are pulverized by ball milling. The powders are consolidated by hot extrusion. Grain growth during consolidation causes the formation of a micrometer-scale microstructure. Mechanical alloying of $Al_{63}Cu_{25}Fe_{12}$ leads to single-phase quasicrystalline powders. which are blended with different volume fractions of pure Al-powder and hot extruded forming $Al_{100-x}$$(Al_{0.63}Cu_{0.25}Fe_{0.12})_x$ (x = 40,50,60,80) micrometer-scale composites. Compression test data reveal a high yield strength of ${\sigma}_y{\geq}$700 MPa and a ductility of ${\varepsilon}_{pl}{\geq}$5% for than the Al-Mn-Ce bulk samples. The strength level of the Al-Cu-Fe alloys is ${\sigma}_y{\leq}$550 MPa significantly lower. By the addition of different amounts of aluminum, the mechanical properties can be tuned to a wide range. Finally, a bulk metallic glass-forming Ti-Cu-Ni-Sn alloy with in situ formed composite microstructure prepared by both centrifugal and injection casting presents more than 6% plastic strain under compressive stress at room temperature. The in situ formed composite contains dendritic hcp Ti solid solution precipitates and a few $Ti_3Sn,\;{\beta}$-(Cu, Sn) grains dispersed in a glassy matrix. The composite micro- structure can avoid the development of the highly localized shear bands typical for the room temperature defor-mation of monolithic glasses. Instead, widely developed shear bands with evident protuberance are observed. resulting in significant yielding and homogeneous plastic deformation over the entire sample.

$\textrm{Fe}_{80-x}\textrm{P}_{10}\textrm{C}_{6}\textrm{B}_{4}\textrm{M}_{x}$(M=Transition Metal) 비정질합금의 열적안정성 (Thermal Stability of $\textrm{Fe}_{80-x}\textrm{P}_{10}\textrm{C}_{6}\textrm{B}_{4}\textrm{M}_{x}$(M=Transition Metal) Amorphous Alloys)

  • 국진선;전우용;진영철;김상협
    • 한국재료학회지
    • /
    • 제7권3호
    • /
    • pp.218-223
    • /
    • 1997
  • 과냉각액체구역(${\Delta}T_{x}=T_{x}-T_{g}$)을 갖는 $Fe_{80}P_{10}C_{6}B_{4}$ 조성에 천이금속(Ti, Zr, Hf, V, Nb, Ta, Cr, Mo, W, Mn, Co, Ni, Pd, Pt및 Cu)를 첨가하여 이들 원소가 유리화온도($T_{g}$), 결정화온도($T_{x}$) 및 과냉액체구역 (${\Delta}T_{x}$)에 미치는 영향에 \ulcorner여 조사하였다. $Fe_{80}P_{10}C_{6}B_{4}$ 합금의 ${\Delta}T_{x}$ 값은 27K였으나 이 합금에 Hf, Ta 및 Mo을 각각 4at%첨가하면 그 값이 40k 이상으로 증가하였다. 이같은 ${\Delta}T_{x}$ 값의 증가는 유리화온도($T_{g}$의 상승보다 결정화온도($T_{x}$)의 상승폭이 크기 때문이다. $T_{g}$$T_{x}$는 외각전자밀도(e/a)가 약 7.38에서 7.05로 감소할수록 상승하였다. e/a의 감소는 천이금속과 다른 구성원소(반금속)사이의 상호결합상태를 의미한다. 즉 $T_{g}$$T_{x}$의 상승은 강한 상호결합력에 기인하는 것으로 사료된다.

  • PDF

분무배소법에 의해 생성되는 복합산화물 분말들의 특성에 미치는 반응인자들의 영향 (Effect of Reaction Factors on the Properties of Complex Oxide Powder Produced by Spray Roasting Process)

  • 유재근;이성수;박희범;안주삼;남용현;손진군
    • 자원리싸이클링
    • /
    • 제9권4호
    • /
    • pp.16-27
    • /
    • 2000
  • 본 연구에서는 기능성 자성재료의 원료분말을 분무배소법에 의해 제조하기 위하여 원료 용액을 효율적으로 미립화시킨 후 반응로 내로 분무시킬 수 있으며, 반응로 내부는 균일한 열분포를 이루어 열분해반응이 완전하게 진행 될 뿐만 아니라, 생성된 분말을 cyclone 및 bag filter 등의 포짐장치에서 효율적으로 포집할 수 있으며, 유해 생성가스를 청정시킬 수 있는 장치까지 포함하는 개선된 분무배소로 system을 제작하였다. 또한 본 연구에서는 불순물들을 다량 함유하고 있는 mill scale 및 ferro-Mirr을 산용액에 용해 시킨 복합 산용액의 pH를 4정도로 조절하여 용액 내에 존재하는 $SiO_2$, P 및 Al 등의 불순물들을 약 20ppm 이하로 감소시킴으로써 mill scale 및 ferro-Mn의 분무열분해를 위한 원료로의 재활용 가능성을 확인하였다. 원료용액인 정제된 복합 산용액을 nozzle을 통하여 분무배소로 내부로분무시킴으로써 Fe-Mn 계의 복합 산화물 분말을 제조하였으며, 반응온도, 원료용액 및 공기의 유입속도, nozzle tip 크기 및 원료용액의 농도 등의 주요 반응조건의 변화에 따른 생성분말의 특성 변화를 파악하였다. 생성된 분말들의 형상은 대부분의 반응조건에서 구형을 나타내고 있었으며, 조성 및 입도분포가 매우 균일하게 혼합된 형태로 나타남으로써 본 연구에 의해 제작된 분무배소로 system의 우수성을 확인할 수 있었다. 한편 본 반응조건 하에서 생성된 분말들의 결정입도가 대부분 약 100nm 이하으 초미립상태이면서 형상 및 입도분포가 매우 균일하다는 사실은 본 연구에서 제작한 분무배소, system을 이용함에 의해 Fe, Mn, Ni, Cu 및 회토류계 염화물로부터 초미립의 산화를 분말을 제조할 수 있을 뿐만 아니라, 반응분위기의 변화에 따라 초미립 순금속분말의 제조도 충분히 가능할 것으로 사료된다.

  • PDF