• Korean Chemical Engineering Research
• /
• 제61권3호
• /
• pp.479-486
• /
• 2023

본 연구에서는 메탄 습식 개질 반응용 Ni/Al₂O₃ 촉매에 첨가된 Ce_xZr_1-xO₂(CZ)가 촉매 반응 효율에 미치는 효과를 조사하였다. 반응 실험 결과, CZ 조촉매가 첨가된 Ni/Al₂O₃ 촉매는 동일 온도, 동일 steam to carbon ratio에서 Ni/Al₂O₃ 촉매보다 높은 메탄 전환율과 수소 수율을 보였다. 특성 분석 결과, 두 촉매 모두 유사한 기공 구조와 비슷한 Ni 분산도를 가지고 있어 이는 반응 효율에 영향을 미치는 요소가 아님을 확인하였다. 하지만, 라만 분광 분석결과에서 CZ 조촉매 첨가 Ni/Al₂O₃ 촉매는 Ni/Al₂O₃ 촉매와 달리 CZ상에서 oxygen vacancy가 존재하고, 이는 상대적으로 낮은 반응 온도에서 물 활성화를 촉진시키는 것으로 확인되었다. CZ 조촉매 상의 oxygen vacancy에 의한 물 활성화는 저온 영역에서 CZ 조촉매 첨가 Ni/Al₂O₃ 촉매의 습식 개질 반응 성능을 증대시켰다.

• 열처리공학회지
• /
• 제7권4호
• /
• pp.253-261
• /
• 1994

Transformation behavior and superelastic behavior of Ti-Ni-Cu alloys with various Cu content has been investigated by means of electrical resistivity measurement, X-ray diffraction, tensile test and transmission electron microscopy. Two types of heat treatment are given to the specimens: i) Solutions treatment. ii) thermo-mechanical treatment. The transformation sequence in solution treated Ti-Ni-Cu Alloys substituted by Cu for Ni up to 5at.% occurs to $B2{\rightleftarrows}B19^{\prime}$ and it proceeds in two stages by addition of 10at.%Cu, i. e, $B2{\rightleftarrows}B19{\rightleftarrows}B19^{\prime}$. Also, it has been found that Ti-30Ni-20Cu alloy transformed in one stage : $B2{\rightleftarrows}B19$. The thermo-mechanically treated Ti-47Ni-3Cu alloy transformed in two stages: B2${\rightleftarrows}$rhomboheral phase${\rightleftarrows}B19^{\prime}$, while transformation sequence in Ti-45Ni-5Cu and Ti-40Ni-10Cu alloy transformed as same as solution treated specimens. The critical stress for inducing slip deformation in solution treated and thermo-mechanically treated Ti-40Ni-10Cu alloy is about 90MPa and 320Mpa respectively.

• 에너지공학
• /
• 제2권3호
• /
• pp.293-299
• /
• 1993

용융탄산염연료전지(MCFC)용 다공성 Ni 양극에 3~10 wt% Al를 첨가하여 tape casting 법으로 제조된 Ni-Al 양극의 전기화학적성능 및 구조적안정성이 조사되었다. 본 연구에서 제조된 양극의 전기화학적 성능이 $650^{\circ}C$, MCFC 양극분위기(80% H$_2$＋20% $CO_2$)를 모사한 half-cell 에서 양분극 특성으로 평가되었는데, 전류밀도 150 ㎃/$\textrm{cm}^2$ 에서의 분극전압은 약 100 ㎷로 실용전지의 양극으로서 가능성을 보였다. Ni-Al 양극의 소결과 creep에 대한 저항성은 Ni 양극에 비해 증가되었는데, 이는 Ni 입자 표면에 형성된 $Al_2$O$_3$의 영향으로 판단되었다.

• 한국수소및신에너지학회논문집
• /
• 제22권6호
• /
• pp.787-793
• /
• 2011

A 76.5wt%Mg - 23.5wt%Ni (Mg-23.5Ni) sample was prepared by reactive mechanical grinding (RMG) and its hydriding and dehydriding properties were then investigated. Activation of the Mg-23.5Ni sample was completed only after two hydriding (under 12 bar $H_2$) - dehydriding (under 1.0 bar $H_2$) cycles at 593K. The reactive mechanical grinding of Mg with Ni is considered to facilitate nucleation and shorten diffusion distances of hydrogen atoms. After hydriding - dehydriding cycling, the Mg-23.5Ni sample contained Mg2Ni phase.

• 한국수소및신에너지학회논문집
• /
• 제17권2호
• /
• pp.174-180
• /
• 2006

The eutectic Mg-23.5%Ni alloy was casted by melting and solidification. The powders of Mg-23.5%Ni and (Mg-23.5%Ni)-10% iron oxide were prepared by mechanical grinding of casted Mg-Ni alloy and casted Mg-Ni alloy+oxide, respectively. As milling time increases, hydriding and dehydriding rates of Mg-Ni and Mg-Ni-oxide alloy powders increase. The additions of iron oxide to Mg-Ni alloy and Mg-Ni-oxide increase hydriding rates and slightly decrease dehydriding rates.

• 한국분말재료학회지
• /
• 제26권2호
• /
• pp.101-106
• /
• 2019

Ni-based oxide dispersion strengthened (ODS) alloys have a higher usable temperature and better high-temperature mechanical properties than conventional superalloys. They are therefore being explored for applications in various fields such as those of aerospace and gas turbines. In general, ODS alloys are manufactured from alloy powders by mechanical alloying of element powders. However, our research team produces alloy powders in which the $Ni_5Y$ intermetallic phase is formed by an atomizing process. In this study, mechanical alloying was performed using a planetary mill to analyze the milling behavior of Ni-based oxide dispersions strengthened alloy powder in which the $Ni_5Y$ is the intermetallic phase. As the milling time increased, the $Ni_5Y$ intermetallic phase was refined. These results are confirmed by SEM and EPMA analysis on microstructure. In addition, it is confirmed that as the milling increased, the mechanical properties of Ni-based ODS alloy powder improve due to grain refinement by plastic deformation.

• Ocean and Polar Research
• /
• 제31권1호
• /
• pp.51-61
• /
• 2009

In this study we define the two different types of El $Ni{\tilde{n}}o$, i.e., the eastern Pacific El $Ni{\tilde{n}}o$ (i.e., EP-El $Ni{\tilde{n}}o$) versus the central Pacific El $Ni{\tilde{n}}o$ (i.e., CP-El $Ni{\tilde{n}}o$), during the boreal summer (June-July-August, JJA) and winter (December-January-February, DJF) using the two NINO indices in the tropical Pacific. The two different types of El $Ni{\tilde{n}}o$ significantly differ in terms of the location of the maximum anomalous sea surface temperature (SST) in the tropical Pacific. The CP-El $Ni{\tilde{n}}o$ has been observed more frequently during recent decades compared to the EP-El $Ni{\tilde{n}}o$. In addition, our analysis indicates that the statistics of CP-El $Ni{\tilde{n}}o$ during JJA is closely associated with the warming trend in the central equatorial Pacific. We also examine the different responses of the East Asian marginal SST to the two types of El $Ni{\tilde{n}}o$ during JJA and DJF. The CP-El $Ni{\tilde{n}}o$ during both JJA and DJF is concurrent with warm SST anomalies around the Korean Peninsula including the East China Sea, which is in contrast to the EP-El $Ni{\tilde{n}}o$. Such different responses are associated with the difference in tropics/mid-latitude teleconnections via atmosphere between the two types of El $Ni{\tilde{n}}o$. Furthermore, our results indicate that atmospheric diabatic forcing in relation to the precipitation variability is different in the tropical Pacific between the EP-El $Ni{\tilde{n}}o$ and the CP-El $Ni{\tilde{n}}o$.

• Tribology and Lubricants
• /
• 제36권3호
• /
• pp.124-132
• /
• 2020

The effect of the stoichiometry on the sliding wear properties of NiAl coatings has been investigated. Three different powder mixtures with the compositions of Ni-50at%Al, Ni-54at%Al and Ni-42at%Al were diepressed respectively, and which were subsequently coated on mild steel through combustion synthesis in an induction heating system. Sliding wear behavior of the coatings was examined against an alloyed tool steel using a pin-on-disc type sliding wear test machine. As results, it could be seen that powder mixture(Ni-54at%Al) with displaying Al-rich deviations from the stoichiometry of NiAl(Ni-50at%Al) was promoted the most the synthetic reactivity. The microstructure of the coating layer with the compositions of Ni-54at%Al exhibits the porous NiAl single phase structure. However, the microstructure of the coating layer of the compositions of Ni-42at%Al exhibits the denser multi-phase structure containing several intermediate phases in addition to NiAl. Densification of the coating layer was enhanced by increasing the reacting temperature. On the other hand, the wear properties of the coating layers showed that the wear mode at speeds of around 1 m/s was severe wear, regardless of the stoichiometry and reacting temperature. However, wear properties of coating layer with the compositions of Ni-42at%Al were superior to those of coating layer with the compositions of Ni-54at%Al. This would be attributed by the fact that coating layer with the compositions of Ni-42at%Al develops little void and much intermediate phases with high strength.

• 한국재료학회지
• /
• 제31권8호
• /
• pp.439-444
• /
• 2021

The oxidation resistance of the diffusion aluminide bond coat (BC) is compromised largely by interdiffusion (ID) effects on coated turbine blades of aeroengines. The present study is designed to understand the influence of ID on βNiAl coatings or BC. In this regard, nickel substrate and CMSX-4 superalloy are deposited. In total, four sets of BCs are developed, i.e. pure βNiAl (on Ni substrate), simple βNiAl (on CMSX-4 substrate), Zr-βNiAl (on CMSX-4 substrate) and Pt-βNiAl (on CMSX-4 substrate). The main aim of this study is to understand the interdiffusion of Al, Zr and Pt during preparation and oxidation. In addition, the beneficial effects of both Zr and platinum are assessed. Pure βNiAl and simple βNiAl show Ni-out-diffusion, whereas for platinum inward diffusion to the substrate is noticed under vacuum treatment. Interestingly, Zr-βNiAl shows the least ID in all BCs and exhibit stability under both vacuum and oxidation treatments. However, its spallation resistance is slightly lower than that of Pt-βNiAl BC. All BCs show similar oxide growth trends, except for Zr-βNiAl, which exhibits two-stage oxidations, i.e. transient and steady-state. Moreover, it is suggested that the localized spallation in all BCs is caused by βNiAl - γ'-Ni₃Al transformation.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.121-121
• /
• 2003

NiO thin films are very attractive for use as an antiferromagnetic layer, p-type transparent conducting films, in electrochromic devices and functional sensor layer for chemical sensors, due to their excellent chemical stability, as well as optical, electrical and magnetic properties. In addition, (100)- and (111)-oriented NiO films can be used as buffer layers on which to deposit other oriented oxide films, such as c-axis-oriented perovskite-type ferromagnetic films and superconducting films, because of the similarity in symmetry of oxygen ion lattice and lattice constants between the NiO films and the oriented oxide films. Thus, controlling the crystallographic orientation and surface roughness of the NiO films for a buffer layer are very important.