• Journal of Korean Society for Atmospheric Environment
• /
• v.13 no.5
• /
• pp.371-381
• /
• 1997

Precipitation sampls were collected in Chonju-city during October 1994 to September 1995 and were analysed for major ions (N $a^{+}$, $K^{+}$, $Ca^{2+}$, $Mg^{2+}$, C $l^{[-10]}$ , NO/$_3$, S $O_4$$^{2-}$) and trace metals (Al, Cd, Ni, Pb, Sr, Zn) in addition to pH, in order to understand the chemical characteristics of acid rain and to estimate the origin of the determined ions. Most rain showed a neutral or alkaline character, and only 35% had a pH lower than 5.6. S $O_4$$^{2-}$ and N $O_3$$^{[-10]}$ are identified as the primary contributors to precipitation acidity in this region. Neutralization of precipitation acidity occurs as a result of the dissolution of alkaline compounds containing $Ca^{2+}$, $Mg^{2+}$ and $K^{+}$. S $O_4$$^{2-}$ and N $O_3$$^{[-10]}$ precipitation concentrations exhibit a seasonal pattern in which higher concentrations are observed during spring months and lower concentrations during summer months. However, the seasonal behavior of $H^{+}$ concentrations differs from this pattern, in that the highest concentrations occur during autumn months, owing to the different influence of neutralization processes. In all rain, S $O_4$$^{2-}$ concentration exceeded NO/$_3$$^{[-10]}$ concentration. The contribution of maritime sources to the total S $O_4$$^{2-}$ concentration was very low or negligible. For rain strongly affacted by yellow sand, $Ca^{2+}$, $Mg^{2+}$ and $K^{+}$ ions show a sharp increase in concentration, reflecting the increased amount of dust and soil suspended in atmosphere. At the same time, S $O_4$$^{2-}$ and N $O_3$$^{[-10]}$ concentrations are at their highest levels while $H^{+}$ values are not comparably elevated, presumably beacause much of the acidity has been neutralized by alkaline substances. The seasonal variance of trace metal concentrations in rainwater is similar to that of major cations. The annual wet flux of acidic pollutants and trace metals wat calculated to be as follows: N $O_3$$^{[-10]}$ ; 2.32 g/$m^2$, S $O_4$$^{2-}$, 5.34 g/$m^2$, Al; 6.30 mg/$m^2$, Cd; 0.62 mg/$m^2$, Ni; 4.08 mg/$m^2$, Pb: 9.76 mg/$m^2$, Sr; 5.94 mg/$m^2$, Zn; 111 mg/$m^2$./$m^2$.

• Journal of the Korean Chemical Society
• /
• v.36 no.4
• /
• pp.579-583
• /
• 1992

Stereoselective synthesis of farnesol, (2E, 6E)-3,7,11-trimethyldodeca-2,6,10-tiren-1-ol(1), was carried out using 5-bromo-2-methylpent-2-ene(2) as a starting material. After conversion of 5-bromo-2-methylpent-2-ene(2) to the corresponding iodide compound, 5-(4-methylpent-3-enyl)-2,3-dihydrofuran(4) was obtained by alkylation of 5-lithio-2,3-dihydrofuran with 5-iodo-2-methylpent-2-ene. Ni(0)-catalyzed coupling reaction of the dihydrofuran 4 with MeMgI was proceeded to give (3E)-4,8-dimethylnona-3,7-dien-1-ol(5) in 72% yield. The resultant homoallylic alcohol 5 was converted to the (5E)-6,10-dimethylundeca-5,9-dien-2-one(8) in 4 steps. Compound 8 was condensed with dimethylmethoxycarbonylmethylphosponate in benzene follwed by $NaBH_4$ reduction in EtOH to yield (2E, 6E)-3,7,11-trimethyldodeca-2,6,10-trien-1-ol(1). Ni(0)-catalyzed coupling reaction of MeMgI with dihydrofuran 4 was a key step in this synthesis of farnesol(1).

• Resources Recycling
• /
• v.29 no.4
• /
• pp.51-57
• /
• 2020

Separation of Co and Ni over Mg from the sulfuric acid solutions using Cyanex272, PC88A and Versatic acid 10 as an extractant was carried out. From the comparative studies about the extraction behavior of Co, Ni and Mg, Versatic acid 10 was superior to Cyanex272 and PC88A for the selective extraction of cobalt and nickel from the mixed solutions. About 98% of Ni and Co were extracted at equilibrium pH 7.0 and less than 5% of Mg was co-extracted by Versatic acid 10. McCabe-Thiele diagram indicated two stages requirement for Co and Ni extraction by 10% Versatic acid 10 at pH 7.0 and phase ratio (A/O) of 2.0. The loaded Co and Ni in organic phase was stripped effectively the sulfuric acid concentration above 70 g/L. 99.78% of cobalt and 98.42% of nickel were stripped.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.133.2-133.2
• /
• 2010

현재 융융탄산염 연료전지의 공기극으로 다공성의 lithiated NiO를 사용하고 있는데 이 재료의 경우 크게 두 가지의 문제점을 안고 있다. 첫 번째는 Ni이 전해질 내로 용해하는 것이고, 두 번째는 낮은 활성으로 인한 높은 공기극의 분극이다. Ni이 전해질로 용해되는 문제는 Co나 Fe를 코팅하여 공기극 표면에 $Li_x(Ni_yCo_{1-y})1-xO_2$나 $Li_x(Ni_yFe_{1-y})_{1-x}O_2$를 형성시켜 NiO의 전해질 내로 용해되는 것을 억제하는 방법이나 ZnO, MgO, $La_2O_3$ 등의 산화물을 NiO 표면에 코팅하여 전해질과 접촉을 막는 방식으로 해결하는 등 많은 연구가 이루어져 왔다. 하지만 연료극의 비해 상당히 높은 공기극의 분극으로 인해 큰 전압손실이 일어나 용융탄산염 연료전지 성능이 낮아지는 문제의 경우 이를 해결하고자 하는 연구는 상대적으로 많이 진행되지 못한 상태이다. 특히 현재 용융탄산염 연료전지의 장기수명화를 위해 기존의 작동온도인 $650^{\circ}C$ 보다 다소 낮은 온도인 $600{\sim}620^{\circ}C$에서 작동하려는 움직임이 있다. 작동 온도가 내려가면 전해질이 휘발되는 속도가 낮아져 전해질 부족에 따른 운전시간이 줄어드는 문제를 해결할 수 있어 장기 수명화를 위해서는 작동온도를 낮추는 것이 매우 유리하다. 하지만 작동 온도가 내려가면서 양 전극에서 일어나는 전기화학 반응 속도가 느려지기 때문에 각 전극에서의 활성화 분극으로 인한 전압손실은 더욱 커질 수밖에 없다. 특히 연료극의 수소산화반응 속도는 공기극의 산소환원반응에 비해 매우 빠르기 때문에 작동 온도가 내려감에 따라 연료극의 분극이 커지는 것에 비해 공기극의 분극이 급격히 커지게 된다. 따라서 운전온도가 낮아지는 상황에서는 낮은 작동온도에서도 성능감소가 적게 일어나 0.8V 이상 운전(150mA/$cm^2$, 단위전지 기준)이 가능한 공기극의 개발이 매우 필요한 실정이다. 이를 해결하고자 본 연구에서는 고체 산화물 연료전지의 공기극의 재료로 많이 연구되고 있는 혼합전도성 물질의 페로브스카이트 구조의 물질을 기존 NiO 전극에 코팅하여 새로운 공기극을 개발하였다. 페로브스카이트 구조의 물질로 대표적인 LSCF 물질을 사용하였으며 LSCF를 코팅한 공기극을 이용한 단위전지에서 150mA/$cm^2$의 전류를 흘려주었을 때 0.84V의 성능을 1000hr 유지하였다. 이는 기존의 NiO 전극을 사용했을 때보다 15~20mV 높은 값이다. 낮은 작동온도에서도 좋은 성능을 보였는데, 기존의 NiO 전극의 경우 $630^{\circ}C$에서 0.79V의 성능을 보인 반면 LSCF가 코팅된 공기극의 경우 $620^{\circ}C$에서 0.811V의 매우 좋은 성능을 보였다. 이는 LSCF의 산소이온전도성 및 전기전도성이 공기극에서의 분극을 낮추어 성능을 증가시키는 것으로 보인다.

• Electrical & Electronic Materials
• /
• v.8 no.6
• /
• pp.768-773
• /
• 1995

We describe a manufacturing method and characteristics on components of molten carbonate fuel cell. Cr, Al, AI$_{2}$O$_{3}$, Co, MgO powder were mixed with Ni powder for anode components and NiO was used for cathode electrode. The electrolyte plate consisted of LiAIO$_{2}$ and carbonate (Li$_{2}$CO$_{3}$/K$_{2}$CO$_{3}$=62/38) and these three were manufactured by doctor-blade method. As a result, open circuit voltage was 1.05[VI at Ni-10Cr anode and porosity was above 60[%].

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.85-90
• /
• 2007

Lanthanum aluminate($LaAlO_3$) film has been prepared on single crystal and metal substrates by dip coating method. Lanthanum acetate and aluminum were prepared via ligand exchange starting from lanthanum nitrate hexahydrate and aluminum nitrate hexahydrate in acetate glacial acetic acid solution after being refluxed. Coating solution was obtained by diluting the gel with methanol and 2-methoxyethanol to adjust the total cation concentration to 0.67 M. Precursor coated film was prepared by dip-coating with a speed of 25 mm/min on various substrates such as $LaAlO_3$ (001), MgO(001), $SrTiO_3$(001) single crystal, LMO/MgO/Ni-alloy. Thin films have been obtained by heat treating the precursor film at various temperatures from $600^{\circ}C{\sim}900^{\circ}C$ and various heating rate from $0.83^{\circ}C/min{\sim}1.25^{\circ}C/min$ under $Ar/O_2$ mixture containing 1000ppm oxygen. The films have been characterized by scanning electronic microscopy (SEM) and X-ray diffraction (XRD). XRD analysis for the prepared film showed that $LaAlO_3$ thin films with a preferred orientation of (100) plane parallel to substrate surface were obtained at $800^{\circ}C(1.11\;^{\circ}C/min)$ on LMO/MgO/Ni-alloy substrate, but the intensity decreased with the increase of heat treatment temperature.

• Korean Journal of Materials Research
• /
• v.10 no.3
• /
• pp.223-226
• /
• 2000

The oxygen deficient ferrites $(Ni_x,\; Zn_{1-x})Fe_2O_{4-{\delta}}$ can decompose $CO_2$ as C and $O_2$ at a low temperature of about $300^{\circ}C$. Ultra powders of $(Ni_x,\; Zn_{1-x})Fe_2O_4$ for the $CO_2$ decomposition were prepared by the hydrothermal methods. The XRD result of synthesized ferries showed the spinel structure of ferrites and ICP-AES and EDS quantitative analyses showed the composition similar with the starting molar ratios of the mixed solution prior to reaction. The BET surface area of the synthesized(Ni, Zn)-ferrites was above $110\textrm{m}^2/g$ and its particle size was very as small as about 5~10 nm. The $CO_2$ decomposition efficiency of the oxygen deficient ferrites($(Ni_x,\;Zn_{1-x})Fe_2O_{4-{\delta}}$) was almost independent with composition and the $CO_2$ decomposition efficiency of ternary (Ni, Zn)-ferrites was better than of binary Ni-ferrites.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.3
• /
• pp.184-189
• /
• 2007

The importance of secondary battery industry is getting excited according to the development of battery industry as a high efficiency energy supplier of electronic machine of mobile information such as mobile phone, lap-top computer, PDA. It is rasing the interest about security of safety and high efficiency of cathode material for main part of secondary lithium battery. The cathode material which has been used like $LiCoO_2,\;LiMn_2O_4,\;LiNi_xCo_yMn_zO_2,\;LiNi_xCo_yM_zO_2$ (M=Al, Zr, Mg etc.,) the most typical material is $LiCoO_2$. But it is studying the development of substitute such as efficiency amelioration of $LiCoO_2$, thetiary element, olivine element because of the capacity of $LiCoO_2$, the matter of security; especially the betterment of efficiency, security research of safety has been actively processed in domestic and overseas about surface coating treatment of active cathode which is using oxide ($M_xO_3$). This study analyses side effect of battery according to increase of surface treatment, formation of precipitation for reagent condensation, non-reagent residue of oxide ($M_xO_3$) which is remains during the surface treatment of $LiCoO_2$; conducts study of new process, the consideration of the electrochemical property to improve oxide solution of mixing rate, mixture of surface treatment, dryness, calcinations conditionetc.

• Applied Chemistry for Engineering
• /
• v.25 no.5
• /
• pp.497-502
• /
• 2014

The conversion reaction of methane and carbon dioxide at an atmospheric pressure plasma reactor filled with Ni-$Al_2O_3$ and Ni-$MgAl_2O_4$ catalyst was performed. Effects of various process parameters such as the applied electric power, reaction gas flow rate, reactor temperature, mixing ratio of reactants and the presence of the catalyst on the reaction between methane and carbon dioxide were analyzed. From the analysis of the contribution of the catalyst in the reaction step, even if the temperature raised to $400^{\circ}C$, there was no spontaneous catalytic conversion of methane and carbon dioxide without plasma discharges. When the catalysts for the conversion of methane and carbon dioxide would be adopted to the plasma reactor, the careful selection of suitable catalysts and process parameters should be essential.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.257-260
• /
• 2003

In this study, the structural, dielectric and piezielectric properities of $xPb(Mg_{1/3}Nb_{2/3})O_3-(0.5-x)Pb(Ni_{1/3}Nb_{2/3})O_3-0.5Pb(Zr_{0.3}Ti_{0.7})O_3$ ceramics were investigated with the substitution of $PbMg_{1/3}Nb_{2/3}O_3$. The results showed that the substitution of the $PbMg_{1/3}Nb_{2/3}O_3$ was effective in increasing the dielectric constant and electromechanical coupling factor $(K_p)$. The dielectric constant, dielectric loss and Kp showed the highest values of 4293, 2.4%, 0.59 relatively, when the substitution of amount of $PbMg_{1/3}Nb_{2/3}O_3$ was 5 mol%.