• Corrosion Science and Technology
• /
• v.7 no.5
• /
• pp.269-273
• /
• 2008

It is known that the fluoric resin has the most outstanding properties in the extremely acidic environment of high temperature. However, this resin is the thermal hardening type that needs long time heat treatments above $250^{\circ}C$. It's impossible to use in situ in the extremely acidic environment such as a huge FGD ductworks or industrial chemical tanks. Furthermore, even the natural hardening type fluoric coatings which can be hardened less than $120^{\circ}C$ can not be applied to the highly acidic environmental plants because of its chemical resistance. In this study, new fluoric coatings that has excellent thermal resistance, chemical resistance and corrosion resistance has been developed in order to solve above problems and to be applied to the large plant structures in the field. These newly developed coatings are organic and inorganic composite type that have fluoric rubber(100 wt%), fluoric resin(5~50 wt%), oxalates(5~30 wt%), inorganic fillers mixed with plate-type and bulk-type solids(20~150 wt%), hardeners(0.5~5 wt%), and hardening hasteners(0.1~3 wt%). The best chemical and physical properties of these coatings are acquired by variation of adhesive reinforcement agents, dispersants, leveling agents. Mixing ratios of plate-type and bulk-type inorganic fillers influence the thermal properties, abrasive resistance and chemical infiltration properties of coatings. The mixing control is also very important to have homogeneous surface and removing inner voids of coatings.

• Journal of Microbiology and Biotechnology
• /
• v.24 no.7
• /
• pp.987-997
• /
• 2014

The mature landfill leachate, which is characterized by a high concentration of ammonia nitrogen ($NH_3$-N) and humic acid (HA), poses a challenge to biotreatment methods, due to the constituent toxicity and low biodegradable fraction of the organics. In this study, we applied bioaugmentation technology in landfill leachate degradation by introducing a domesticated $NH_3$-N and HA resistant bacteria strain, which was identified as Bacillus cereus (abbreviated as B. cereus Jlu) and Enterococcus casseliflavus (abbreviated as E. casseliflavus Jlu), respectively. The isolated strains exhibited excellent tolerant ability for $NH_3$-N and HA and they could also greatly improved the COD (chemical oxygen demand), $NH_3$-N and HA removal rate, and efficiency of bioaugmentation degradation of landfill leachate. Only 3 days was required for the domesticated bacteria to remove about 70.0% COD, compared with 9 days' degradation for the undomesticated (autochthonous) bacteria to obtain a similar removal rate. An orthogonal array was then used to further improve the COD and $NH_3$-N removal rate. Under the optimum condition, the COD removal rate in leachate by using E. casseliflavus Jlu and B. cereus Jlu increased to 86.0% and 90.0%, respectively after, 2 days of degradation. The simultaneous removal of $NH_3$-N and HA with more than 50% and 40% removal rate in leachate by employing the sole screened strain was first observed.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.19 no.3
• /
• pp.175-192
• /
• 2017

The purpose of this study is to provide the characteristics and development direction of K-fashion and to systematize the strategic features performed by government agencies, fashion associations, fashion companies, and other companies to activate K-fashion. This research analyzed K-fashion related articles published in major newspapers and magazines in Korea from the late 1990s to early 2017. The results of the study are as follows. 1. The characteristics of K-fashion are as follows: The first is a trendy and sophisticated design with modern sensibilities, unique designs that reinterpret the latest trends with designer creativity, practical and popular designs that ordinary people can wear comfortably in everyday life. The second is functional and trendy materials. The third is excellent sewing technology. The fourth is rapid turnover of products by quick connections among planning, production and sales. The fifth is a lower price than quality. 2. The direction for K-fashion to pursue was the continuous and ongoing development of the above characteristics and the creation of a 'design with the Korean emotion of its 5,000 year history'. 3. The following projects were carried out to promote K-fashion. 1) Utilization of K-pop, K-drama and other Korean wave content. (1) Holding a fashion concert event that combines Idol's K-Pop performances with fashion shows. (2) Hallyu (Korean wave) star's costume support and design collaboration with Hallyu stars. (3) Collaboration between entertainment companies and fashion companies. 2) Nurturing a global fashion branding project. 3) Business support for overseas expansion of the K-fashion brand. (1) Support project for foreign trade fair participation. (2) Holding a fashion brand fair in Korea. (3) Overseas business support by establishing a showroom and design center 4) Business to discover and nurture new designers

• Journal of Korea Game Society
• /
• v.14 no.5
• /
• pp.137-146
• /
• 2014

Recently, the games on the market are getting rich and excellent in the category of design and productions. The style and production quality of cut-scenes also have achieved a continuous development, so how to stand out from multiple designs and gain popularity always acts as a challenge to designers. However, such design strategy up to developers will be failed to judge whether or not design achievements are loved by players and thus cannot meet rapidly changing market demands on both in a quantity and quality. Therefore, this study holds that cut-scene design for video games must set out from user-centered design(UCD). According to literatures with respect to product market, we know that Market Pull imposes far more impacts on success in bringing new products to the market than the technology Push, hence players actually determines the success of a game in competitive game market. This study will help to enhance the immersion of playing game, including the interest and standing out the designer's message without distorting the original impression in the game publishing environment.

• Journal of the Korean Institute of Gas
• /
• v.18 no.4
• /
• pp.51-55
• /
• 2014

This paper was analyzed for a sealing characteristics of single lip contact type o-ring and multiple lip contact type packing for a swivel joint using the finite element method. According to the FE analysis, a conventional o-ring produces a maximum contact normal stress of 2.5MPa for a supplied LP gas pressure of 1.8MPa, which is related to the sealing performance. But, a sealing performance of newly invented multi-lip packing produces a maximum contact normal stress of 3.01MPa, which is 20.4% higher than that of a conventional o-ring. And an extrusion of a conventional o-ring, which is strongly related to the sealing endurance safety, was occurred at a supplied gas pressure of 1.62MPa. But, a multi-lip packing does not produce up to the gas pressure of 1.8MPa. This means that a new type of multi-lip packing may have excellent sealing characteristics because of no extrusion for high gas pressure. Thus, multi-lip packing with multiple lip contacts may be useful for high sealing and endurance safety compared to that of the conventional o-ring with a single lip contact.

• Korean Chemical Engineering Research
• /
• v.50 no.3
• /
• pp.479-491
• /
• 2012

In this paper we performed evaluation of the economics of a district heating system (DHS) consisting of energy suppliers and consumers, heat generation and storage facilities and power transmission lines in the capital region, as well as identification of optimal operating conditions. The optimization problem is formulated as a mixed integer linear programming (MILP) problem where the objective is to minimize the overall operating cost of DHS while satisfying heat demand during 1 week and operating limits on DHS facilities. This paper also propose a new forecasting model of the system marginal price (SMP) using past data on power supply and demand as well as past cost data. In the optimization, both the forecasted SMP and actual SMP are used and the results are analyzed. The salient feature of the proposed approach is that it exhibits excellent predicting performance to give improved energy efficiency in the integrated DHS.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.6
• /
• pp.586-594
• /
• 2009

This paper is the study on random, sinusoidal and shock vibration responses for the STSAT-3(science and technology satellite-3) proto-model which is the first small size all-composite satellite in Korea. The structure system of the STSAT-3 forms box type structure by joining several hybrid sandwich panels comprised of honeycomb core and carbon fiber reinforced laminated composite skins on both side. Mode shape, stress, displacement and acceleration responses are obtained on both the frequency domain and time domain by means of a commercial FEA software MSC/NASTRAN. From these analysis results, failure, safety factor and design validity are assessed. These results can be successfully applicable as reference data when a new satellite is developed as well as giving out an excellent criteria in satellite vibration treatment design.

• Proceedings of the Korea Contents Association Conference
• /
• 2008.05a
• /
• pp.301-305
• /
• 2008

An organic light-emitting diode(OLED) has advantages of low power driving, self light-emitting, wide viewing angle, excellent high resolution, full color, high reproduction, fast response speed, simple manufacturing process, or the like. However, there are still a number of challenges to get over in order to put it to practical use as a high performance display. First of all, the most important thing is to improve the efficiency of the OLED element in order to commercialize it. To this end, its efficiency can be improved by lowering the driving voltage through the improvement of structure of the OLED element and the application of new organic substance. Therefore, in this study, we have manufactured a red OLED element by applying fluorescent dyes to the emitting layer of the element having the structure of ITO/TPD/Znq2+DCJTB/Znq2/Al and the structure of ITO/CuPc/NPB/Alq3+DCJTB/Alq3/Al, in order to light-emitting various colors or improve the brightness and the efficiency, and then we have evaluated its electrical and optical characteristics.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.3
• /
• pp.25-34
• /
• 2001

In this paper, discharge lamp ozonizer(DLO) of a new discharge type using superposition of gaseous electrical discharge for environment improvement was designed and manufactured. DLO is equipped with 3 electrodes(central ground electrode of discharge lamp type internal high voltage electrode of mesh type and external high voltage electrode of spiral type), and it is composed of double gap(gap between discharge lamp and internal electrode, gap between discharge lamp and external electrode). Internal and external electrodes are respectively applied AC high voltage which has 180[$^{\circ}$] phase difference. Ozone is generated by overlaying of each silent discharge which is respectively came from two gaps. At the moment discharge characteristics and ozone generation characteristics of DLO were investigated in accordance with quantity of supplied gas, discharge power and the number of DLO. When ozone generated by DLO was in contact with NO gas, removal characteristics was excellent, so it confirmed that DLO could be used as air environment improvement facility.

• Macromolecular Research
• /
• v.16 no.6
• /
• pp.510-516
• /
• 2008

New antitumor active polymers, poly(methacryloyl-2-oxy-1,2,3-propanetricarboxylic acid-co-exo-3,6-epoxy-l,2,3,6-tetrahydrophthalic acid) [poly(MTCA-co-ETAc)], poly(methacryloyl-2-oxy-l,2,3-propanetricarboxylic acid-co-hydrogen ethyl-exo-3,6-epoxy-l,2,3,6-tetrahydrophthalate) [poly(MTCA-co-HEET)], and poly(methacryloyl-2-oxy-l,2,3-propanetricarboxylic acid-co-a-ethoxy-exo-3,6-epoxy-1,2,3,6-tetrahydrophthaloyl-5-fluorouracil) [poly(MTCA-co-EETFU)] were synthesized and characterized. Their antitumor activity, inhibition of DNA replication and antiangiogenesis were examined. The structures of the polymers were identified by FT-IR, $^1H$ and $^{13}C$-NMR spectroscopy. The number average molecular weights of the fractionated polymers determined by GPC ranged from 9,400 to 14,900, and polydispersity indices were less than 1.7. The in vitro cytotoxicity of these polymers was determined and their antitumor activity was evaluated. The $IC_{50}$ values (the drug concentration at inhibition of 50% tumor growth) indicated that the synthesized polymers were much better inhibitors of cancer cells and showed lower cytotoxicity than the free 5-FU. The in vivo antitumor activity of the conjugates was examined using mice bearing the sarcoma 180 tumor cell line. The life spans (TIC) of the mice treated with the conjugates were higher than those treated with the free 5-FU. In addition, the synthesized conjugates showed excellent antiangiogenic activity based on an embryo chorioallantoic membrane assay.