• Nuclear Engineering and Technology
• /
• 제54권7호
• /
• pp.2572-2578
• /
• 2022

An approximate method for calculating the cadmium ratio of a cyclotron-based thermal neutron radiography system was developed. In this method, the Monte-Carlo code, MCNP6.2, was employed to calculate the neutron capture rates of Au-197, and the cadmium ratio was obtained by computing the ratio of neutron capture rates. From the simulation results, the computed cadmium ratio is reasonably acceptable, and the assumption of ignoring the fast neutron contribution to the cadmium ratio is valid.

• 한국가시화정보학회지
• /
• 제9권4호
• /
• pp.63-68
• /
• 2011

The flow-field of a liquid-metal system is very important for the safety analysis and the design of the steam generator of liquid-metal fast breeder reactor. Dynamic neutron radiography (DNR) is suitable for a visualization and measurement of a liquid metal flow and a two-phase flow in a metallic duct. However, the three dimensional DNR techniques is not enough to obtain the velocity information in the wide channel up to now. In this research, a high speed DNR technique was applied to visualize the heavy liquid-metal flow field in the narrow channel with the HANARO-beam facility. The images were taken with a high frame-rate neutron radiography at 250 fps and analyzed with a Particle Image Velocimetry(PIV) method. The images were compared with the results of the commercial CFX code to study the feasibility of DNR technique for the measuring the heavy liquid-metal flow field. The PIV images could discern the turbulent vortex flow in the two-dimensional narrow channel.

• Nuclear Engineering and Technology
• /
• 제53권10호
• /
• pp.3413-3420
• /
• 2021

Applying the available neutron flux for medical and industrial purposes is the most important application of research reactors. The neutron radiography system is used for non-destructive testing (NDT) of materials so that it is one of the main applications of nuclear research reactors. One of these research reactors is the 5 MW pool-type light water research reactor of Tehran (TRR). This work aims to investigate on materials and location of the beam tube (BT) of the TRR radiography system to improve the index parameters of BT. Our results showed that a through-type BT with 20 cm thick carbon neutron filter, 1.2 cm and 9.4 cm of the diameter of inlet (D₁) and output (D₂) BT, respectively gives thermal neutron flux almost 25.7, 5.6 and 1.1 times greater than the former design of the TRR (with D₁ = 1.8 cm and D₁ = 9.4 cm), previous design of the TRR with D₁ = 3 cm and D₁ = 9.4 cm, and another design with D₁ = 5 cm and D₁ = 9.4 cm, respectively. Therefore, the design proposed in this paper could be a better alternative to the current BT of the TRR.

• Nuclear Engineering and Technology
• /
• 제49권4호
• /
• pp.781-786
• /
• 2017

The presence of crust on the inner walls of metallic ducts impairs transportation because crust completely or partially hinders the passage of fluid to the processing unit and causes damage to equipment connected to the production line. Its localization is crucial. With the development of the electronic imaging system installed at the Argonauta/Nuclear Engineering Institute (IEN)/National Nuclear Energy Commission (CNEN) reactor, it became possible to visualize crust in the interior of metallic piping of small diameter using real-time neutron radiography images obtained with a low neutron flux. The obtained images showed the resistance offered by crust on the passage of water inside the pipe. No discrepancy of the flow profile at the bottom of the pipe, before the crust region, was registered. However, after the passage of liquid through the pipe, images of the disturbances of the flow were clear and discrepancies in the flow profile were steep. This shows that this technique added the assembled apparatus was efficient for the visualization of the crust and of the two-phase flows.

• Nuclear Engineering and Technology
• /
• 제41권1호
• /
• pp.135-142
• /
• 2009

In this investigation, we prepared a 1 and 3-parallel serpentine single PEMFC, which has an active area of $100\;cm^2$ and a flow channel cross section of $1{\times}1mm$. Distribution and transport of water in a non-operating PEMFC were observed by varying flow types and the flow rates (250, 400, and 850 cc/min). This investigation was performed at the neutron imaging facility at the CO1d Neutron RAdiography facility (CONRAD), HMI, Germany of which the collimation ratio and neutron fluence rate are 250, $1{\times}10^{6}n/s/cm^2$, respectively. The neutron image was continuously recorded by a scintillator and lens-CCD coupled detector system every 10 seconds. It has been observed that although the distilled water was supplied into the cathode channel only, the neutron image showed a water movement from the cathode to the anode channel. The water at the cathode channel was completely discharged as soon as the pressurized air was supplied. But the water at the anode channel was not easily removed by the pressurized air except for the 3-parallel serpentine type with 850cc/min of air flow rate. Moreover, the water at the MEA wasn't removed for any of the cases.

• 전기화학회지
• /
• 제10권1호
• /
• pp.20-24
• /
• 2007

최근 높은 에너지 밀도를 갖고 있는 리튬 이온 이차전지에 대한 관심이 높다. 리튬 이온 이차전지는 이미 휴대용 기기로 널리 적용되고 있으며, 하이브리드 전기자동차와 같은 고출력 전지시스템에 적용을 위해 연구되고 있다. 리튬 이온 이차전지의 전극 소재는 리튬 이온의 이동에 의해서 충전 및 방전되는 현상을 활용한다. 전극으로부터 리튬 이온이 이동될 때 전극내의 구조 변화가 발생한다. 전극의 구조분석은 중성자 또는 X-선을 이용하여 분석할 수 있다. X-선은 분석 시간이 짧고, 쉽게 분석할 수 있다는 장점이 있으나 원자내의 전자구름과의 산란을 응용하므로 전자가 적은 가벼운 원소의 경우 분석이 어려운 단점이 있다. 리튬도 원자량이 작아서 X-선 만으로는 리튬의 정확한 위치에 대한 분석이 어렵다. 중성자 분석기술은 이에 대한 해답이 될 것이다. 본 자료에서는 중성자를 활용한 전극물질의 구조 분석 사례 및 그 원리에 대해서 논의하고자 한다.