• 대한토목학회논문집
• /
• 제28권4A호
• /
• pp.487-495
• /
• 2008

본 연구에서는 압출가설시 압출노즈와 가설거더 시스템의 거동에 대한 압출노즈의 휨강성비, 단위중량비 및 길이비의 영향을 살펴보고, 압출과정에서 발생하는 부모멘트 및 정모멘트를 최소화할 수 있는 압출노즈에 대한 최적조건을 도출하고자 하였다. 또한, 도출된 최적조건을 사용하여 압출노즈의 단위중량비와 길이비의 관계식을 유도하고 압출가설시에 발생하는 절대최대 정모멘트 및 부모멘트의 산정식을 제시하였으며, 연속거더교량의 압출가설시에 사용되는 압출노즈의 최적설계 방안을 제안하였다. 가장 이상적인 압출노즈의 설계는 절대최대 부모멘트를 최소화하면서 절대최대 정모멘트의 발생을 억제할 수 있는 단위중량비 0.167, 길이비 0.836을 적용한 경우임을 확인하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.285-286
• /
• 2002

The lubricating characteristics of negative pressure slider were performed by using divergence formulation method with the coordinate transformation method. This method makes it possible to deal with an arbitrary configuration of a lubricated surface. The pressure profile of the slider is calculated. These results are compared to that from direct numerical method. The steady-state, including minimum film thickness, pitching and rolling angle are calculated by multi-dimensional Newton-Rapson method. The stiffness and damping characteristics are also calculated.

• Smart Structures and Systems
• /
• 제30권1호
• /
• pp.89-106
• /
• 2022

The negative stiffness of an active or semi-active damper system has been proven to be very effective in reducing dynamic response. Therefore, energy dissipation devices possessing negative stiffness, such as viscous inertial mass dampers (VIMDs), have drawn much attention recently. The control performance of the VIMD for cable vibration mitigation has already been demonstrated by many researchers. In this paper, a new optimal design procedure for VIMD parameters for taut cable vibration control is presented based on the fixed-points method originally developed for tuned mass damper design. A model consisting of a taut cable and a VIMD installed near a cable end is studied. The frequency response function (FRF) of the cable under a sinusoidal load distributed proportionally to the mode shape is derived. Then, the fixed-points method is applied to the FRF curves. The performance of a VIMD with the optimal parameters is subsequently evaluated through simulations. A taut cable model with a tuned VIMD is established for several cases of external excitation. The performance of VIMDs using the proposed optimal parameters is compared with that in the literature. The results show that cable vibration can be significantly reduced using the proposed optimal VIMD with a relatively small amount of damping. Multiple VIMDs are applied effectively to reduce the cable vibration with multi-modal components.

• Steel and Composite Structures
• /
• 제36권4호
• /
• pp.481-492
• /
• 2020

To study the rail mapped deformation caused by the pier settlement of simply - supported bridges with China Railway Track System III (CRTS III) slab ballastless track (SBT) system under the mode of non-longitudinal connection ballastless track slab, this study derived an analytical solution to the mapped relationships between pier settlement and rail deformation based on the interlayer interaction mechanism of rail-pier and principle of stationary potential energy. The analytical calculation results were compared with the numerical results obtained by ANSYS finite element calculation, thus verifying the accuracy of analytical method. A parameter analysis was conducted on the key factors in rail mapped deformation such as pier settlement, fastener stiffness, and self-compacting concrete (SCC) stiffness of filling layer. The results indicate that rail deformation is approximately proportional to pier settlement. The smaller the fastener stiffness, the smoother the rail deformation curve and the longer the rail deformation area is. With the increase in the stiffness of SCC filling layer, the maximum positive deformation of rail gradually decreases, and the maximum negative deformation gradually increases. The deformation of rail caused by the pier settlement of common-span bridge structures will generate low-frequency excitation on high-speed trains.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.553-558
• /
• 1998

Two-way slab-column specimens were tested under monotonic loading increased up to punching shear failure to investigate the beneficial effects of fiber-reinforced concrete. The parameters for experiments are the placement of fibers within the immediate column region, the placement on the entire surface of the slab, and no placement of fibers. The effects of these parameters on the punching shear capacity, negative moment cracking. and stiffness of the two-way slab specimens were studied. According to the results the addition of steel fibers in the slab around the column results in a significant improvement in the performance including the increase of punching shear resistance, greater post-cracking stiffness and smaller crack width at service load levels.

• The Journal of Korean Physical Therapy
• /
• 제31권6호
• /
• pp.346-350
• /
• 2019

Purpose: The purpose of this study was to investigate the effects of calf tightness on gait, plantar pressure, and balance in adults. Methods: A total of 60 participants were divided into a normal group of 30 subjects with normal dorsiflexion angle (20-25 degrees) and an experimental group of 30 subjects with limited dorsiflexion angle (0-15 degrees) due to calf tightness. Gait ability and foot pressure of the subjects was measured with a treadmill, and the balance ability was measured by PROKIN system. Results: A significant difference in COP length, loading response, and single limb support was observed between groups. The COP length and single limb support ratio in the normal group was greater than in the experimental group, but the experimental group showed a higher ratio for loading response in the gait ratio. Conclusion: Our results indicated that calf tightness was negative effects on balance and gait ability, so assessment of the muscle tightness should be considered during exercise and treatment.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제8권2호
• /
• pp.39-49
• /
• 2004

Model of the novel Surface motor (SFM) is briefly discussed, and two types of control method including two-order feedback circuit control, indirect acceleration feedback control are analyzed to solve unstable characteristic such as low damp and negative stiffness. The simulation results demonstrate that the system has plain amplitude and wide frequency band arranging from 0 to 8kHz with no resonant peak through indirect acceleration feedback control.

• 한국철도학회논문집
• /
• 제10권5호
• /
• pp.499-505
• /
• 2007

본 연구의 주목적은 고속선 콘크리트 슬래브 궤도시스템에서 레일패드의 피로효과에 따른 영향을 분석하는 데에 있다. 이에 3차원 해석모델 및 실내시험을 통해 도출된 레일패드의 피로효과(경화, 스프링계수 증가)가 고속선 궤도의 역학적 거동에 미치는 영향을 분석하였다. 본 연구에서는 콘크리트 슬래브 궤도의 적정 탄성력 확보여부를 의미하는 레일패드의 적정스프링계수 산정에 관한 연구의 일환으로 고속철도 콘크리트 슬래브 궤도에 적용된 레일체결시스템에 대한 실내시험을 통한 레일패드의 정적스프링계수를 산정하고 체결시스템에 대한 피로시험을 통해 도출된 피로효과가 고려된 레일패드의 스프링계수 변화를 해석모델에 적용함으로써 향후 고속선 콘크리트 슬래브 궤도운영에서의 열차 주행안정성 확보 및 합리적인 궤도유지관리를 위한 기초데이터를 확보하고자 한다.

• 한국소음진동공학회논문집
• /
• 제18권4호
• /
• pp.411-423
• /
• 2008

Pneumatic vibration isolator has a wide application for ground-vibration isolation of vibration-sensitive equipments. Recent advances In precision machine tools and instruments such as nano-technology or medical devices require a better isolation performance, which can be efficiently done by precise modeling- and design- of the isolation system. This paper will discuss an efficient transmissibility design method for pneumatic vibration isolator by employing the complex stiffness model of dual-chamber pneumatic spring developed in our previous research. Three design parameters of volume ratio between the two pneumatic chambers, the geometry of capillary tube connecting the two pneumatic chambers and finally the stiffness of diaphragm necessarily employed for prevention of air leakage were found to be important factors in transmissibility design. Based on design technique that maximizes damping of dual-chamber pneumatic spring, trade-off among the resonance frequency of transmissibility, peak transmissibility and transmissibility in high frequency range was found, which was not ever stated in previous researches. Furthermore this paper will discuss about negative role of diaphragm in transmissibility design. Then the design method proposed in this paper will be illustrated through experiment at measurements.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.202-207
• /
• 2002

This paper deals with a novel shunted actuator, which has a capability to suppress multi-mode vibration amplitudes by using a pair of piezoceramic patches. In order to describe the characteristic behaviors of shunted dampers connected with a series and a parallel resistor-negative capacitive branch circuit, the stiffness ratio and loss factor with respect to the non-dimensional frequency are considered. To obtain a guideline model of a piezo/beam system connected with a series and a parallel resistor-negative capacitor branch circuit, the governing equations of motion is derived through Hamiltons principle and a piezo sensor equation as well as a shunt damping matrix is developed. The theoretical analysis shows that the shunted actuator developed in this study can significantly reduce multiple-mode vibration amplitudes simultaneously over the whole structural frequency range.