• Journal of Sensor Science and Technology
• /
• v.20 no.4
• /
• pp.238-242
• /
• 2011

This paper describes the fabrication and characteristics of a low frequency vibration driven electromagnetic energy harvester. The fabricated generator consists of a permanent magnet of NdFeB, a FR-4 planar spring and a Copper cylinder type coil. ANSYS modal analysis was used to determine the resonant frequency for the generator. The implemented generator is capable of producing up to 550 mV peak-to-peak under 7 Hz frequency, which has a maximum power of $95.5\;{\mu}W$ with load resistance of $580\;{\Omega}$. This device is shown to generate sufficient power at different resonating modes, and the experimental and simulated results are discussed and composed.

• Journal of Sensor Science and Technology
• /
• v.20 no.2
• /
• pp.102-106
• /
• 2011

This paper presents a design and analysis of an electromagnetic micro generator which can convert low frequency vibration energy to electrical power. The design aspects of the micro generator comprised planar spring, Cu coil and a permanent magnet(NdFeB). Threetype spring designs and four materials(Parylene, FR-4, Cu and Si) were compared to find resonance frequency. It was found that the resonance frequency will be changed according to the spring shape and material. Mechanical and magnetic parameters had been adjusted to optimize the output power through a comprehensive theoretical study.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.942-949
• /
• 2014

We studied about the rotor design change using a Ferrite ring magnet to reduce material cost in the condition of the same stator core design. However, this design direction has many weak points such as the decrease of BEMF, the low maximum output, the irreversible demagnetization characteristics of a permanent magnet and so on. In order to mitigate such disadvantages, an optimization design of the BLDC motor has been developed by changing each design parameter and by improving the electromagnetic structure. In the proposed water pump SPM BLDC motor using Ferrite magnet, the outer and inner diameter of stator is fixed to the value of the conventional IPM BLDC motor using Nd-Fe-B magnet. The design specification requirements should be satisfied with the same output power and efficiency characteristics in the same dimension. As a result of this study, the design comparison results considering driving performances and material cost are represented. Through the actual experiment with the prototype of the designed motor, the simulations results are verified.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.15-17
• /
• 2001

BLDC 전동기의 제작시 영구자석의 가격은 전체 가격을 결정하는데 높은 비중을 갖는다. 이런 영구자석의 크기를 최적화시킬 수 있다면 비용절감이 예상된다. 본 논문은 BLDC 전동기에서 고가(高價)의 영구자석의 재료비용을 절감시키기 위한 설계방법을 제시한다. 기본적인 설계방법은 영구자석 내부에서 적정한 동작점을 갖는 한계 내에서 영구자석의 크기를 줄이는 것이다. 그리고 전동기의 전체크기를 비례적으로 증가시킴으로써 요구되는 기본파 자속을 보상한다. BLDC 전동기의 자기적 특성은 유한요소법을 사용하여 해석하였다. 회전자의 위치에 따라 계산되는 유한요소 해석결과의 magnetic vector potential을 이용하여 권선의 자속을 계산하였고, 기본파의 성분은 푸리에 변환으로 얻었다. 설계사례로서 영구자석 대 기타부분의 비용을 각각 80/20, 70/30, 60/40, 50/50으로 가정할 때 기존 전동기 비용에 대해서 크기가 새로이 조정된 전동기 비용을 비교 검토하였다.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.104-106
• /
• 2001

In this paper, it is object of design of high efficiency slotless BLDC motor using film coil. Slotless BLDC motor is able to have high efficiency property and low cogging torque, due to magnetization of stator core have constant contribution by slotless core. But it is difficult to make coil winding of slotless BLDC motor. So we make amateur of slotless BLDC motor using film coil. Film coil is fabricated by drilling, electro-plating and etching of copper/insulator/copper plate. In this paper, after design of slotless BLDC motor for moving axial blower, it is fabricated by NdFeB permanent magnet type rotor and film coil.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1264-1266
• /
• 2005

This paper analyzes static and transient response characteristics of a permanent magnet type stepping motor with claw poles using three-dimensional finite element method. The outer diameter of the stepping motor to be analyzed is approximately 6 mm. In this paper we analyzes only 2 poles of the stepping motor, which has 10 magnetic poles made up of NdFeB material, using periodic boundary condition. We clarify transient response and static torque charateristics using Maxwell 3D and Matlab Simulink.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.824-827
• /
• 1995

Dielectromagnets are permanent magnets made from resin-bonded hard magnetic powders. Magnetic properties of dielectromagnets depend on kind of used hard magnetic materials as chemical compound, shape, size of grain and applied technology. Comparison of advantages and disadvantages of dielectromagnets made from different kind of magnetic powders induced us to try to prepare dielectromagnets from mixture of hard magnetic powders, not only one of them. The purpose of investigation on this kind of dielectromagnets is to find formula to prepare permanent magnets with properties adequate to different kind of electrical motors requirements. As hard magnetic materials we used powders of ferrite, melt-spun ribbon Nd-Fe-B and Alnico. Papers present results of investigation on technology of this kind of dielectromagnets. It shows also influence of kind of mixture and used technology on magnetic properties of dielectromagnets.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.376-379
• /
• 1995

Employing the muffin-tin-orbital theory combined with pseudo-potential concepts, we have evaluated hybridization matrix elements between R and T sites in $RT_{2}$ compounds. The matrix elements are calculated with two parameters, the interatomic distance between R and T atoms from the crystal structure data, and the expectation values of the radial distances for the radial wave functions of the ground state charge densities, which are obtained from the linearized muffin-tin orbital band method within the local density approximation. It is found that the R 4f/T 3d hybridization matrix elements decrease with an increasing atomic number from R=Ce to Gd, and that they are smaller in $RNi_{2}$ than in $RCo_{2}$, which are consistent with trends observed in recent photoemission spectroscopy experiments. It is also found that the magnitudes of the hybridization matrix elements in $RFe_{2}$ are comparable to those in $RNi_{2}$.

• Journal of Magnetics
• /
• v.17 no.3
• /
• pp.210-213
• /
• 2012

To detect the surface and the opposite side cracks on iron specimen under AC and DC magnetic fields, the planar inductive coil sensors were employed. When the induced signals were measured, the planar inductive coil sensor and the magnetic field source were lifted off about 2 mm from the top surface of the specimen. AC magnetic fields and DC magnetic fields were applied to the specimens by single straight Cu coil and NdFeB permanent magnet, respectively. The detected signals at crack positions were good coincidence with those of the simulation results.

• 한국문화재보존과학회:학술대회논문집
• /
• 2004.10a
• /
• pp.137-153
• /
• 2004

We have analyzed the ingredients of 17 pieces of Bronze Age bronze ware, and an additional 22 pieces of Koryo and Chosun dynasty bronze ware. We have also conducted analysis of the extraction sites where these bronze ware items were found. For analyzing the main ingredient the bronze ware items have been divided into 3 groups - Cu-Sn(70?75:20), Cu-Pb-Sn(70:10:10), Cu-Pb-Sn(60:10:20) type respectively. In tile cases of the Cu-Pb-Sn groups the division comes down to differences in the Cu content as the main component, and elements such as Ni, Fe, Co contribute as a micro ingredient. The geographical and periodic characteristics of ancient bronze ware items show that theircompositional element changes from Cu:Sn to Cu:Pb:Sn and the Cu content decreases with the period,while the Pb content increases with the period. Bronze ware items from Suchon Ri, Gongju (that were used in 3 B.C.) form very different categories from 3rd ${\~}$ 2nd B.C.. They additionally formed very different categories from those bronze ware items analyzed in this research. These bronze ware itemsare shown to be geographically close and periodically overlapped, but made of a new elemental composition. This shows an inflow of a production technical culture present in the new bronze wares. The main component content of Cu is lower, and the Co and Fe contents (as microelements) are much higher than that of other bronze ware items. Such facts showthat those bronze ware items used completely different materials from bronze ware items in other cultural areas, or that there were differences in smelting techniques In the places where ancient bronze ware items have been extracted, it is presumed that the materials originated from the southern parts of Korea andnorthern parts and southern parts of China. .As more bronze ware scientific research is compiled one can conclude that that there will be enough scientific evidence to study the Bronze Age culture of Koreasystematically.