• Journal of Oral Medicine and Pain
• /
• v.22 no.1
• /
• pp.15-22
• /
• 1997

In order to investigate the antibacterial effects of pulsed Nd:YAG Laser concerning to Streptococcus mutans, Streptococcus mutans was cultured and standardized and plated in 96 well plates. After that, black dye and chlorhexidine were applied and pulsed Nd:YAG Laser was irradiated to plates. Experimental groups which was applied with black dye and chlorhexidine were divided into 5 groups by concentration. And experimental groups and control group were subdivided as unlased and lased of 20, 40, and 60J. After laser irradiation, All groups were plated in agar plates and incubated for 18 hours. Bacterial colonies were counted and analysed comparitively, and the temperature of culture medium was measured on every laser irradiation. The results were obtained as follows; 1. In case of laser irradiation only, there is no significant reduction in number of Streptococcus mutans by irradiated energy of laser. 2. In case of black dye application, there is no difference by concentration of black dye but there is decrease when applied Laser and black dye simultaneously. 3. When applied chlorhexidine, the number of Streptococcus mutans was decreased according to increase of concentration, but there is no difference by irradiated energy of laser. 4. The temperature of culture medium was increased according to increase of irradiated energy of Laser, and the number of Streptococcus mutans was reduced remarkably just above 50 centigrade and killed above 70 centigrade. As above results, pulsed Nd:YAG Laser has well-absorbing affinity to black dye. And antibacterial effect of pulsed Nd:YAG Laser against Streptococcus mutans is seemed to be due to increase of temperature.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.85-95
• /
• 1997

This study is to investigate the optimum conditions of Nd:YAG laser beam welding for Zircaloy-4 end cap closure by optical fiber transmission. Laser welding parameters which affect the penetration depth and bead width were experimentally examined using the various beam radius by the beam quality analyzer, joint geometries of end cap and the laser parameters which mean pulse width, repetition rate and pulse energy. Also, an optimum welding speed and the effect of assistant gas with varying the flow rate of He were investigated. We found that the laser average power for the end cap welding will be 230W and rotation speed must not exceed 8 RPM, the best position of focus using optical fiber with 600.mu.m will be 2 to 3mm below the surface of the material.

• Korean Journal of Optics and Photonics
• /
• v.10 no.1
• /
• pp.53-57
• /
• 1999

We established the laser oscillator using Nd:YAG crystal grown at Ssang Yong company in Korea and investigated the characteristics of oscillation, Q-switching and wave front of output beam. We measured the single pass gain by controlling the threshold input energy with two output couplers of different output reflectances. Moreover, we compared the gain measured by different output couplers with the gain directly measured by the laser amplifier. The peak power of Q-switching, the pulse width, and the single pass gain coefficient at the threshold energy were 1.5 MW, 30ns, and 0.0958 cm-$^1$ respectively and they were compared with those of the commercial Nd:YAG crystal. Our crystal was proved to be as good as the commercial crystal.

• Korean Journal of Optics and Photonics
• /
• v.14 no.5
• /
• pp.515-520
• /
• 2003

Characteristics of an amplifier with repetition rate of a few KHz is investigated. The continuous flash lamp pumped Nd:YAG laser head is used as an amplifier. The thermally induced birefringence of the laser medium is compensated and the depolarization is reduced to 5% in a double-pass amplifier. The amplification factor of a four pass amplifier reaches to about 3.2 at the repetition rate 5-10 KHz and the pulse width is lengthened from 40 ns to 48 ns.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.24-32
• /
• 2007

Laser surface hardening is beneficially used for surface treatment of structural steel. Due to very rapid heating and cooling rates, structural low-alloy steel(SCM4) can be hardened as self quenching. The aim of this research project is to improve the influence of the process laser parameters: laser power, spot size, surface roughness, and traverse speed. The laser beam is allowed to scan on the surface of the workpiece at the constant power(1095W), varying the traverse speed at 0.3m/min, 0.5m/min and 0.8m/min. The optical lens with the elliptical profile is designed to obtain a wide surface hardening area with uniform hardness. From the results of the experiment, it has been shown that the stable hardness is about 600$\sim$700Hv, when the laser power, focal position and the traverse speed are P=1095W, z=0mm and v=0.3m/min.

• Laser Solutions
• /
• v.3 no.3
• /
• pp.13-19
• /
• 2000

The stencil is a thin stainless sheet in which a pattern is formed, which is placed on a surface of plate to reproduce the pattern of electric circuit. Conventionally the stencil has been produced by etching process. This process has many anti-environmental factors. In this study, Nd : YAG laser cutting process has been applied for stencil manufacturing. The study is focused on estimating kerf width of laser cut stencil by E.B.P.(Error Back-Propagation). This algorithm is good for estimating target value from input value. In this paper, target value was kerf width, and input values were frequency, pulse width, cutting speed and laser power. E.B.P. after teaming input and target could estimate kerf width from some variables precisely.

• Journal of Welding and Joining
• /
• v.15 no.3
• /
• pp.99-108
• /
• 1997

For the conventional welding method, the high heat transfer makes the crystallization of the work material unavoidable. Whereas the laser is able to weld the amorphous metal without a crystallized zone, because heat transfer is limited withn a very small restricted volume. In this paper, the possibilities and the limits of the laser welding in a deep frozen environment by liquid nitrogen were studied to utilize the advantageous properties of amorphous metal foils. The author investigated, after laser welding in a deep frozen environment with a solid state laser (Nd:YAG-laser), the achievable strengths and the influences of the laser beam parameters on the strengths.

• Electrical & Electronic Materials
• /
• v.9 no.6
• /
• pp.593-599
• /
• 1996

Laser scribing of silicon plays an important role in metallization including the grid pattern and the front surface geometry which means aspect ratio of metal contacts. To make a front metal electrode of buried contact solar cell, we used ND:YAG lasers that deliver average 3-4W at TEM$\_$00/ mode power to sample stage. The Q-switched Nd:YAG laser of 1.064 gm wavelength was used for silicon scribing with 20-40.mu.m width and 20-200.mu.m depth capabilities. After silicon slag etching, the groove width and depth for buried contact solar cell are -20.mu.m and 30-50.mu.m respectively. Using MEL 40 Nd:YAG laser system, we can scribe the silicon surface with 18-23.mu.m width and 20-200.mu.m depth controlled by krypton arc lamp power, scan speed, pulse frequency and beam focusing. We fabricated a buried contact Silicon Solar Cell which had an energy conversion efficiency of 18.8 %. In this case, the groove width and depth are 20.mu.m and 50.mu.m respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.78-78
• /
• 1999

Experimental studies of laser micromachining on Mo metal using piezo Q-switched Nd:YAG laser have been performed. Miniaturized microcolumn electron gun arrays as a potential electron beam lithography or portable mini-scanning electron microscope application have recently extensively examined. For these purpose, the electro-static electron lens and deflector system called microcolumn has to be assembled. The conventional microcolumn fabrication technique would gave a limitation on the minimization of aberration. The current technique of a 1 $\mu$m misalignment would lead to ~1.3 nm coma. In order to reduce aberration, assembling the microcolumn component followed by laser drilling should be very beneficial. In this report, we will address the preliminary report of laser micromachining on Mo substrate using piezo Q-switched Nd:YAG laser. The geometrical figures, such as the diameter and the depth of the frilled aperture are dependent upon the total energy of the laser pulse train, laser pulsewidth, and the diameter of laser beam in addition to the materials-dependent parameters.

• Applied Science and Convergence Technology
• /
• v.26 no.4
• /
• pp.66-69
• /
• 2017

Physically implanted surface islands of Nano Carbon Tube (NCT) and ${\alpha}-F_2O_3$ particles have been produced on Al-doped ZnO (AZO)/glass surfaces by simple and direct ND:YAG laser beam irradiation. Sheet resistance of the reconstructed surface increased by about 3.6% of over AZO. Minimal surface damage can be repaired by ND:YAG laser beam irradiation in conjunction with proper impurities. Implanted islands of NCT, which are considered to be a good conductive impurity, on AZO increased the sheet resistance by about 1.8%, while implanted islands of ${\alpha}-F_2O_3$, an insulating impurity, on AZO increased sheet resistance by about 129% compared with a laser beam treated AZO. This study provides insight regarding surface implantations of nanowires and micro-circuits, doping effects for semiconductors and optical devices, surface area and impurity effects for catalysis.