• 한국전기전자재료학회논문지
• /
• 제21권2호
• /
• pp.126-130
• /
• 2008

In this study, in order to develop low loss multilayer piezoelectric actuator, PZN-PZT ceramics were fabricated using $Li_2CO_3,\;Bi_2O_3$, CuO and ZnO as sintering aids, their structural, piezoelectric and dielectric characteristics were investigated according to the amount of ZnO addition, At the sintering temperature of $870^{\circ}C$, the density, electromechanical coupling factor(kp), mechanical quality factor(Qm), dielectric constant(${\epsilon}_r$) and piezoelectric constant($d_{33}$) of 0.4 wt% ZnO added specimen (sintered at $870^{\circ}C$) showed the optimum value of $7.812g/cm^3$, 0.535, 916, 1399, 335 pC/N respectively. Taking into consideration above piezoelectric properties of the specimen sintered at low temperature, it was concluded that PZN-PZT ceramics using 0.4 wt% ZnO as additive showed the optimum characteristics as the composition ceramics for low loss multilayer piezoelectric actuator application.

• 전기학회논문지
• /
• 제59권11호
• /
• pp.2021-2025
• /
• 2010

Electrical and structural properties were investigated on the effects of ZnO and the lead-free NKN-LST ceramics with the addition of ZnO were fabricated by a conventional mixed oxide method. A gradual change in the crystal and microstructure was observed with the increase of ZnO addition. For the NKN-LST-ZnO ceramics sintered at $1050^{\circ}C$, bulk density increased with the addition of ZnO and showed maximum value at addition 2.0mol% of ZnO. Curie temperature of the NKN-LST-ZnO ceramics slightly decreased with adding ZnO. The dielectric constant, piezoelectric constant ($d_{33}$) and electromechanical coupling factor ($k_p$) increased at the small amount of ZnO addition, which might be due to the increase in density. The high piezoelectric properties = 153 pC/N, electromechanical coupling factor = 0.484 and dielectric constant = 2883 were obtained for the NKN-LST+0.5ZnO ceramics sintered at $1050^{\circ}C$ for 2h.

• Transactions on Electrical and Electronic Materials
• /
• 제12권6호
• /
• pp.249-252
• /
• 2011

We investigated the low firing of $Li_2CO_3$ added $0.2Pb(Mg_{1/3}Nb_{2/3})O_3$ - 0.3Pb($Fe_{1/2}Nb_{1/2}$) - $0.5Pb(Zr_{0.475}Ti_{0.525})O_3$ (PMN-PFN-PZT) ceramics and multilayer actuators (MLAs) using Ag inner electrodes. It was found that 0.1 wt% $Li_2CO_3$ was quite effective in lowering the sintering temperature of PMN-PFN-PZT ceramics from $1,100^{\circ}C$ down to $900^{\circ}C$ without deteriorating their piezoelectric ceramics ($d_{33}$ = 425 pC/N and $k_p$ = 61.9%). However, excess $Li_2CO_3$ up to 0.3 wt% brings about unwanted problems such as the formation of a $LiPbO_2$ secondary phase and subsequent degradation in the piezoelectric properties. Using 0.1 wt% $Li_2CO_3$ added PMN-PFN-PZT ceramics, MLAs with Ag inner electrodes were successfully fabricated, resulting in a normalized strain of 580 pm/V at an electric field of 1.5 kV/mm.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.253-253
• /
• 2007

압전 액츄에이터 및 초음파진동자의 응용범위가 넒어짐에 따라 변위량, 응력 등을 개선시키기 위해 전기기계결합계수 kp 및 압전 d상수가 종전보다 큰 재료가 요구되고 있으며, 초음파진동자나 압전 모터와 같이 마찰에 의한 열손실이 많이 발생하는 액츄에이터에 적용할 큰 기계적품질계수롤 가지는 저손실 압전 액츄에이터 및 초음파진동자용 재료가 필요한 실정이다. PZT계 세라믹스는 높은 유전상수와 압전특성으로 전자세라믹스분야에서 가장 널리 사용되어지고 있지만, $1200^{\circ}C$이상의 높은 소결온도 때문에 $1000^{\circ}C$ 부근에서 급격히 휘발되는 PbO로 인한 환경오염과 기본조성의 변화로 인한 압전특성의 저하가 문제시 되고 있다. $Pb(Ni_{1/3}Nb_{2/3})O_3$는 약 $-120^{\circ}C$정도의 큐리온도룰 가지는 강유전체로 Pb(Zr, Ti)$O_3$계 세라믹스에 치환 시 유전상수와 전기기계결합계수를 개선시키는 대표적인 성분이다. 따라서 본 연구에서는 저온소결 저손실의 적층형 압전 액츄에이터를 개발하기 위해 PMS-PMN-PZT계 세라믹스에 $Pb(Ni_{1/3}Nb_{2/3})O_3$ 세라믹스를 치환하고 $Li_2CO_3$와 $Na_2CO_3$ ZnO를 소결조재로 사용하여 저온소결 하였으며 PNN 치환량에 따른 결과를 관찰 하였다.

• 대한전자공학회논문지
• /
• 제11권6호
• /
• pp.1-15
• /
• 1974

본 연구는 탄성파 지연선에 이용되는 탄성표면파중에서 SH표면파 모우드에 대하여 이론적 해석을 하였으며 그 결과 전기-기계적 결합계수가 크며 또한 여전 매질내 깊이 방향으로 아주 작은 감쇠률을 갖고 표면을 따라 전파됨을 알았단. 예로서 PZT-4인 경우 에너지의 80%가 감쇠되는 깊이는 190파장이 된다. 또한 탄성표면파 지연선을 하나의 계단자강으로서 취급하여 삽입손실를 구하였으며 특히 SH표면파 모우드와 같이 전기-기계론 결합계수가 큰 경우는 인터디지탈 트랜스듀셔의 전극폭과 윤극간 간격 사이의 비에 따라 중심 주파수가 현저히 달라진다. 그리고 탄성파 지연선의 온도계수를 벌크파인 종파, 횡파에 대하여 구하였으며 LiTaO2 Z축방향 전파의 횡파는 지연시간의 온도계수가 5.4X10-6/℃로 아주 작아짐을 알았다. 또한 LiNbO3의 130°, 64° 로테이트 Y캇트, X전파의 탄성표면파의 온도계수가 이론치와 잘 일치함을 실험적으로 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 센서 박막재료 반도체재료 기술교육
• /
• pp.111-118
• /
• 2002

A new lithium niobate optical modulator with a polymer buffer layer on Ni in-diffused optical waveguide is proposed for the fist time, successfully fabricated and examined at a wavelength of 1.3 mm. By determining the diffusion parameters of Ni in-diffused waveguide to achieve more desirable mode size which is well matched to the mode in the fiber, the detailed results on the achievement of high optical throughput are reported. In addition, the usefulness of polymer buffer layer which can be applicable to a buffer layer in Ni in-diffused waveguide devices is demonstrated. Several sets of channel waveguides fabricated on Z-cut lithium niobate by Ni in-diffusion were obtained and on which coplanar traveling-wave type electrodes with a polymer-employed buffer layer were developed by a conventional fabrication method for characterizing of electro-optical performances of the proposed device. The experimental results show that the measured half-wave voltage is of ~10 V and the total measured fiber-to-fiber insertion loss is of ~6.4 dB for a 40 mm long at a wavelength of =1.3 mm, respectively. From the experimental results, it is confirmed that the polymer-employed buffer layer in LiNbO3 optical modulator can be a substitute material instead of silicon oxide layer which is usually processed at a high temperature of over $300^{\circ}C$. Moreover, the fabrication tolerances by using polymer materials in LiNbO3 optical modulators are much less strict in comparison to the case of dielectric buffer layer.

• 한국전기전자재료학회논문지
• /
• 제25권8호
• /
• pp.611-615
• /
• 2012

In this study non-stoichiometric $(K_{0.5}Na_{0.5})_{0.97}(Nb_{0.96-x}Ta_xSb_{0.04})O_3$ ceramics were prepared by the conventional soild-state teaction method. The effect of Ta-substitution on the dielectric and piezoelectric properties were investigated. X-ray diffraction analysis of all the specimens less than x= 15 mol% indicated orthorhombic phase. Thereafter, the specimens showed orthorhombic phase near to pseudo-cubic. Sinterablity of all the specimens was improved due to secondary products such as KCT and KCN. The ceramics with x= 5 mol% showed the optimum velues of pizoelectric constant($d_{33}$)= 150 pC/N, electromechanical coupling factor (kp)= 0.45, electromechanical quality factor (Qm)= 418.9 and dielectric constant(${\varepsilon}_r$)= 567. Accordingly, These results indicate that the composition ceramics is a promising candidate for lead-free material.

• 한국전기전자재료학회논문지
• /
• 제24권11호
• /
• pp.870-875
• /
• 2011

The $(Na_{0.52}K_{0.44})(Nb_{0.9}Sb_{0.06})O_3-0.04dLiTaO_3$ (NKNS-LT) ceramics with various $Cu_2O$ concentration were prepared by the conventional solid state reaction method. The $Cu_2O$ content was varied in the range of 0.1~0.4 wt%. The effects of Cu on microstructure, crystallographic phase transition, and piezoelectric properties were investigated. The material with perovskite structure had a tetragonal phase (T1) when $Cu_2O$ concentration was less than 0.3 wt% and it transformed to another tetragonal phase (T2) when the $Cu_2O$ amount was greater than 0.3 wt%. The phase boundary between T1 and T2 phases appeared at around 0.3 wt% of $Cu_2O$ concentration. The piezoelectric properties were shown the maximum values at the composition of the phase boundary. The electro-mechanical coupling factor ($k_p$) was 0.42 and the piezoelectric charge constant ($d_{33}$) was 245 pC/N at the 0.3 wt% of $Cu_2O$ concentration.

• 대한기계학회논문집A
• /
• 제25권3호
• /
• pp.510-519
• /
• 2001

The tensile and fracture toughness tests have been conducted to investigate the degradations of mechanical properties induced mainly by neutron irradiations in Zr-2.5Nb CANDU pressure tube materials operated in Wolsung Unit-1. the tests were performed at room, 150, 200, 250, 300 $\^{C}$ for the irradiated and unirradiated specimens in hot cell. The specimens were directly machined from the tube retaining original curvature using specially designed electric discharge machine(EDM). From the tensile tests of the irradiated specimens, it was found that tensile strength was increased and total elongation was decreased compared to those of the unirradiated ones. The active voltages in the fracture toughness tests for the irradiated showed the discontinuous abrupt increases caused by crack jumping in lower temperature. In the crack resistance curves we found the stable crack growth in the unirradiated, whereas the unstable and three crack growth stages in the irradiated specimens due to the accumulated irradiation defects. The various fracture characteristic values in the irradiated are remarkably lower than those of the unirradiated. Through the fractography, we found in the irradiated that smaller dimple and shorter fissures than the unirradiated, and that the fractured surface had three regions that were flat, transition and slant/shear area. These can explain the difference in the crack growth characteristic values of the irradiated and the unirradiated ones.

• 한국전기전자재료학회논문지
• /
• 제21권3호
• /
• pp.227-231
• /
• 2008

In this study, in order to improve the electrical properties of low temperature sintering piezoelectric ceramics, $[0.05Pb(Zn_{1/2}W_{1/2})-0.07Pb(Mn_{1/3}Nb_{2/3})-0.088Pb(Zr_{0.48}Ti_{0.52})]O_3$(abbreviated as PZW-PMN-PZT) ceramic systems were fabricated using $Bi_2O_3$, CuO and $Li_2CO_3$ as sintering aids and then their piezoelectric and dielectric properties were investigated according to the amount of $Li_2CO_3$ and post-annealing process. Post-annealing process enhanced all physical properties except for mechanical quality factor (Qm). 0.2 wt% $Li_2CO_3$ added and post-annealed specimen showed the excellent values suitable for low loss piezoelectric actuator application as follow: the density = 7.86 $g/cm^3$ electromechanical coupling factor (kp) = 0.575, piezoelectric constant $d_{33}$ = 370 pC/N, dielectric constant ($\varepsilon_r$) = 1546, and mechanical quality factor (Qm) = 1161, respectively.