• Progress in Superconductivity
• /
• 제7권1호
• /
• pp.22-27
• /
• 2005

We have studied the standardization of critical temperature measurements by using an ac susceptometer. Wire forms of NbTi, $Nb_{3}Sn$, and Bi-2223 superconductors were prepared to measure the temperature dependences of the magnetization. In order to study the optimum ac magnetic field and frequency, various amplitudes from 2 Oe to 10 Oe with frequencies from 11.3 Hz to 1033 Hz were applied to three specimens. Analytical comparison of the magnetic curves with the resistive curves was accomplished to investigate validity of using the new method.

• 전자공학회논문지D
• /
• 제35D권6호
• /
• pp.72-78
• /
• 1998

Ti:LiNbO$_3$ 광도파로위에 CPW 전극 구조를한 광변조기 내부칩을 제작한 후 일련공정에 따라 패키징 작업을 하였고 소자의 전기적특성과 광학적특성을 측정하였다. 광변조기 패키징을 위하여 페룰, 보조용 LN블럭 및 글래스, 진동 및 흡수용패드, 알루미나피더의 부분품을 사용하였으며 피그테일링, Au 와이어본딩, 에폭싱, SMA커넥팅, 실링 작업을 수행하였다. 전기적 특성에서 S/sub 21/은 -3 dB 점에서 9.8GHz의 값을, S/sub 11/은 14.4 GHz 대에서 -8.9 dB 값을 나타내었다. 광학적 특성은 제작된 광도파로가 1550nm 파장대에서 단일모드를 만족하였고, 패키지후 소자의 삽입손실은 실온에서 4.3 dB 이였으며, 소자를 온도감압챔버에 넣은후 5∼45℃까지 온도변화를 주었을 때 4.3∼6.4 dB의 삽입손실을 보였다. E-O bandwidth 응답은 3dB점에서 7.8GHz를 나타내어 10Gbps급 광통신시스템에 응용할수 있음을 확인하였다.

• Progress in Superconductivity
• /
• 제9권1호
• /
• pp.23-28
• /
• 2007

In order to have a superconductive connection between the wire-wound pickup coil and input coil, typically Nb terminal blocks with screw holes are used. Since this connection structure occupies large volume, large stray pickup area can be generated which can pickup external noise fields. Thus, SQUID and connection block are shielded inside a superconducting tube, and this SQUID module is located at some distance from the distal coil of the gradiometer to minimize the distortion or imbalance of uniform background field due to the superconducting module. To operate this conventional SQUID module, we need a higher liquid He level, resulting in shorter refill interval. To make the fabrication of gradiometers simpler and refill interval longer, we developed a novel method of connecting the pickup coil into the input coil. Gradiometer coil wound of 0.125-mm diameter NbTi wires were glued close to the input coil pads of SQUID. The superconductive connection was made using an ultrasonic bonding of annealed 0.025-mm diameter Nb wires, bonded directly on the surface of NbTi wires where insulation layer was stripped out. The reliability of the superconductive bonding was good enough to sustain several thermal cycling. The stray pickup area due to this connection structure is about $0.1\;mm^2$, much smaller than the typical stray pickup area using the conventional screw block method. By using this compact connection structure, the position of the SQUID sensor is only about 20-30 mm from the distal coil of the gradiometer. Based on this compact module, we fabricated a magnetocardiography system having 61 first-order axial gradiometers, and measured MCG signals. The gradiometers have a coil diameter of 20 mm, and the baseline is 70 mm. The 61 axial gradiometer bobbins were distributed in a hexagonal lattice structure with a sensor interval of 26 mm, measuring $dB_z/dz$ component of magnetocardiography signals.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.146-149
• /
• 1999

A 30kVA superconducting generator has been designed, developed and successfully tested recently. The design is based on 2-dimensional electromagnetic field analysis. The rotor has been wound with superconducting wire of Nb-Ti alloy. The stator has the air-gap type armature windings. Open-circuit test, short-circuit test and lamp load test have been conducted. The details of design program, design, machinebuilding, test results and conclusions are given in this paper.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1300-1302
• /
• 1998

Residual resistance ratio ( RRR ) of Cu/Nb-Ti Superconductor wire was evaluated by fixed point method. Our measured value of RRR showed good consistency with the average value obtained from round robin test conducted by IEC/TC 90. Our test results showed that the coefficient of variation ( COV ) was kept within 2 %

• 한국초전도ㆍ저온공학회논문지
• /
• 제18권2호
• /
• pp.37-41
• /
• 2016

This paper presents the developed quench analysis code and protection circuit design for a superconducting magnet system of 28GHz electron cyclotron resonance (ECR) ion source. The superconducting magnet is composed of a hexapole magnet and four solenoid magnets located outside of the hexapole one. All magnets are wound with NbTi composite wire and impregnated by epoxy. By using the developed characteristic analysis code, the normal zone resistance, decaying current and temperature rising can be estimated during quench. Also, the stored magnetic energy is successfully consumed from the series resistor of the designed protection circuit. The analytical results are compared with the experimental results to verify the developed quench analysis code and protection circuit.

• 대한전기학회논문지
• /
• 제35권1호
• /
• pp.36-43
• /
• 1986

Superconducting magnet can be employed in many fields, such as, magnet for strong field, superconducting rotating machine and superconducting energy storage system. In this paper, the solenoid magnet design procedure and materials used in construction are described in detail, and those are the fundamentals of superconducting magnet study. The fabrication and test procedure of 3 Tesla superconduting magnet are also described. Nb-Ti is used as a superconducting wire, GFRP and Kapton are used for electrical insulation. Inner diameter of the magnet is 10 cm. According to the test results, the field at the central point of the magnet was 3 Tesla, evaporation rate per hour was 2.7 litter and current at that case was 315 A.

• 한국초전도ㆍ저온공학회논문지
• /
• 제18권1호
• /
• pp.50-54
• /
• 2016

In this paper, a hybrid method is proposed to design an air-core superconducting solenoid system for 6 T axial uniform magnetic field using Niobium Titanium (NbTi) superconducting wire. In order to minimize the volume of conductor, the hybrid optimization method including a linear programming and a nonlinear programming was adopted. The feasible space of solenoid is divided by several grids and the magnetic field at target point is approximated by the sum of magnetic field generated by an ideal current loop at the center of each grid. Using the linear programming, a global optimal current distribution in the feasible space can be indicated by non-zero current grids. Furthermore the clusters of the non-zero current grids also give the information of probable solenoids in the feasible space, such as the number, the shape, and so on. Applying these probable solenoids as the initial model, the final practical configuration of solenoids with integer layers can be obtained by the nonlinear programming. The design result illustrates the efficiency and the flexibility of the hybrid method. And this method can also be used for the magnet design which is required the high homogeneity within several ppm (parts per million).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.232-234
• /
• 1999

A 30kVA superconducting generator (S.G.) has been designed, developed and successfully tested in KERI before the end of last year. The design is based on 2-dimensional electromagnetic field analysis of cylindrical coordinate. The field winding of rotor has been wound with superconducting wire of Nb-Ti alloy and tested after assembled with other rotor components. The stator has air-gap type armature windings which allow higher terminal voltage and more sinusoidal voltage waveform than conventional iron cored machines. Steady-state open & short-circuit test and lamp load test have been conducted also. The results of tests are given in this paper and compared with design quantities. Moreover the cooling scheme and characteristics of test system is included.

• 한국초전도ㆍ저온공학회논문지
• /
• 제24권3호
• /
• pp.24-29
• /
• 2022

One of the recent proposals with nuclear magnetic resonance (NMR) is a multi-bore NMR which consists of array of magnets which could present possibilities to quickly cope with pandemic virus by multiple inspection of virus samples. Low temperature superconductor (LTS) can be a candidate for mass production of the magnet due to its low price in fabrication as well as operation by applying the helium zero boil-off technology. However, training feature of LTS magnet still hinders the low cost operation due to multiple boil-offs during premature quenches. Thus in this paper, LTS magnet with low mechanical stress is designed targeting the "training-free" LTS magnet for mass production of magnet array for multi-bore NMR. A thorough process of an LTS magnet design is conducted, including the analyses as the followings: electromagnetics, mechanical stress, cryogenics, stability, and protection. The magnet specification was set to 4.7 T in a winding bore of 85 mm, corresponding to the MR frequency of 200 MHz. The stress level is tolerable with respect to the wire yield strength and epoxy crack where mechanical disturbance is less than the minimum quench energy.