• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.131-134
• /
• 2002

The effect of the addition on the densification, low temperature sintering, and microwave dielectric properties of the Ca[($Li_{1/3}Nb_{2/3}$)$_{1-x}$$Ti_{x}$]$O_{3-{\delta}}$/(CLNT) was investigated. $Bi_2O_3$ additives improved the dencification and reduced the sintering temperature from $1150^{\circ}C$ to $900^{\circ}C$ of CLNT microwave dielectric ceramics. As increasing $Bi_2O_3$ contents, the dielectric constants and bulk density were increased. The quality factor, however, was decreased slighty. The temperature coefficients of the resonant frequency shifted positive value as increasing $Bi_2O_3$ contents. The dielectric properties of Ca[($Li_{1/3}Nb_{2/3}$)$_{1-x}$$Ti_{x}$]$O_{3-{\delta}}$ and Ca[($Li_{1/3}Nb_{2/3}$)$_{0.8}Ti_{0.2}$]$O_{3-{\delta}}$ with 5wt% $Bi_2O_3$ sintered at $900^{\circ}C$ for 3h were $\varepsilon_{r}$=20, 35 Q.$f_{0}$=6500, 11,000 GHz, $\tau_{f}$=4, 13 ppm/$^{\circ}C$, respectively.

• 한국세라믹학회지
• /
• 제53권2호
• /
• pp.145-149
• /
• 2016

$(Bi_{1/2}Na_{1/2})_{0.94}Ba_{0.06}(Ti_{1-x}Nb_x)O_3$ (BNBTxNb) ceramics were investigated in terms of the crystal structure as well as the ferroelectric, dielectric, and piezoelectric properties. While little change was observed in the microstructure except for a slight decrease in the average grain size, a significant change was noticed in the temperature dependence of dielectric and piezoelectric properties. It was shown that the property changes are closely related to the downward shift in the position of the ferroelectric-to-relaxor transition temperature with increasing amount of Nb doping. A special emphasis is put on the fact that Nb doping is so effective at decreasing the ferroelectric-to-relaxor transition temperature that even at no more than 2 at.% Nb addition, the transition temperature was already brought down slightly below room temperature, resulting in the birth of a large strain at 0.46 %, equivalent to $S_{max}/E_{max}=767pm/V$.

• 한국세라믹학회지
• /
• 제39권9호
• /
• pp.835-839
• /
• 2002

Micro-Pulling Down(${\mu}$-PD)법을 이용하여 직경 1 mm, 길이 30∼35 mm의 $Er_2O_3$와 MgO가 첨가된 화학양론조성 $LiNbO_3$단결정을 성장하였다. 성장된 결정의 $Er_2O_3$와 MgO 첨가에 따른 up-conversion 특성의 변화 및 MgO 첨가량이 광손상에 미치는 영향을 관찰하기 위해 투과율을 측정하였다. 또한 $LiNbO_3$ 단결정 내의 결함유무를 광학현미경을 이용하여 관찰하였고, Electron Probe Micro Analysis(EPMA)를 이용하여 결정 내에 $Er_2O_3$와 MgO가 균일하게 분포되어있음을 확인하였다.

• 한국표면공학회지
• /
• 제54권4호
• /
• pp.178-183
• /
• 2021

The temperature and frequency dependence of the dielectric constant of the BaTiO₃ substituted with two types of donor dopants, Nb⁵⁺ and Ta⁵⁺, respectively, were compared and analyzed. Dielectric specimens of four specific compositions, Ba_0.95Nb_0.05TiO₃, Ba_0.90Nb_0.10TiO₃, Ba_0.95Ta_0.05TiO₃, and Ba_0.90Ta_0.010TiO₃ were prepared by calcining at 1100 ℃ and sintering at 1300 ℃ to have a perovskite structure to measure capacitance. XRD and SEM analysis were used to observe the structure, with particular focus on the integration into the Nb⁵⁺ and Ta⁵⁺ substituted BaTiO₃ crystal lattice. X-ray diffraction peaks in the (200) and (002) planes were observed between 45.10° and 45.45° of the BaTiO₃ solid solution substituted with different fractions of Nb⁵⁺ and Ta⁵⁺. The dielectric properties were analyzed and the relationship between the properties and structure of the substituted BaTiO₃ was established. The fine particles and high density of the substituted BaTiO₃ were maintained like pure BaTiO₃, and in particular, a shift toward the low temperature side of the phase transition temperature range was clearly found, unlike pure BaTiO₃. In addition, the phase transition at a temperature higher than the Curie temperature relatively satisfies the modified Curie-Weiss law.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.76-76
• /
• 2009

PZT세라믹스는 높은 압전특성과 우수한 큐리온도($400^{\circ}C$)를 보유하고 있어 오래시간에 걸쳐 주목받고 있다. 현재 압전변압기, 액츄에이터, 센서등의 압전소자는 PZT를 이용하여 제작하고 있지만 PZT는 고온 소결시 PbO의 휘발이 환경오염을 초래하며 인체의 유해하다는 연구결과가 나왔다. 이에 최근에는 PbO가 포함 되지않은 무연(lead-free)계 압전세라믹스가 주목받고 있다. 무연 압전 세라믹스의 종류로는 Bi-layer-structured ceramics, Bi-perovskite type ceramics, NKN base ceramics 가 존재하고 있다. 그 중 $(Na_{0.5}K_{0.5})NbO_3(NKN)$ 세라믹스는 높은 큐리온도와($400^{\circ}C$)와 높은 전기기계 결합계수(약 36%)를 보유하고 있어 많은 연구가 이루어 지고 있다. 하지만 NKN은 PZT에 비하여 치밀성이 낮으며 일반적인 산화물 소결방법으로는 밀도를 높이기가 어려운 단점이 존재한다. 이를 개선하기 위한 방법으로 hot pressing와 spak plasma sintering, RTGG와 같은 방법으로 밀도를 높일수 있지만 비용이 많이 들어 일반적으로 사용이 어렵다. 다른 방법으로 NKN에 첨가물을 넣는 방법을 사용하고 있는데 방법으로 $LiNbO_3$, $LiTiO_3$, $LiSbO_5$를 첨가하여 개선하는 방법이 있다. 본 실험은 첨가물을 넣는 방식으로 비화학양론적 $(Na_{0.5}K_{0.5})_{0.97}(Nb_{0.9}Ta_{0.1})O_3(NKNT)$조성에 CuO를 mol%로 변화주어 유전 및 압전 특성을 조사하였다.

• 한국전기전자재료학회논문지
• /
• 제15권6호
• /
• pp.499-503
• /
• 2002

In this study, to develop the high power piezoelectric transformer for adaptor, PSN-PNN-PZT system ceramics were formulated as a function of $MnO_2$ addition and its dielectric and piezoelectric characteristics were investigated. Multi-layer piezoelectric transformer using an excellent composition was also fabricated and its electrical properties evaluated. The composition ceramics added to 0.5wt%$MnO_2$ showed the maximum value of $k_p=0.61$ and $Q_m=1.321$. As the output power of piezoelectric transformer is increased, its temperature rise increased. At the fixed 18W output power, the transformer was stably operated.

• 소성∙가공
• /
• 제29권1호
• /
• pp.37-43
• /
• 2020

Increasing the critical current density of superconducting wire is one of the difficult challenges in the field of superconductivity. It is well known that the higher volume fraction of uniformly dispersed α-Ti is able to enhance the critical current density of superconducting material NbTi because α-Ti serves as a flux pinning center. The volume fraction of α-Ti highly depends on the grain size of NbTi because α-Ti precipitates at the grain boundaries or triple points. For this purpose, we investigated the effect of initial microstructures of NbTi obtained from hot rolling in various temperature conditions on the critical current density. In addition, subsequent heat treatment was assigned to precipitate α-Ti and groove rolling/cold drawing was adopted to produce a wire with a diameter of about 1.0 mm. It was observed that the band structure was formed after hot rolling at 500~600℃. It was also found that the volume fraction of α-Ti after hot rolling at 500~600℃ was higher and it led to the highest critical current density.

• 유통과학연구
• /
• 제16권2호
• /
• pp.47-51
• /
• 2018

Purpose - Typically, retailers will want PB(Private Brand) products to expand to the needs of low-PB loyal customers as well as existing PB(Private Brand) loyal customers. Therefore, a strategy of minimizing the share of the manufacturer brand in the distributor can be considered as a way to maximize the profit of the distributor. Research design, data, and methodology - In the previous study, the researches about the rivalry and conflict between the NB(National Brand) products and the PB products were mainly made. Previous studies did not model inter-national brand-level competition and inter-store competition. In addition, they have focused only on distributors' decisions from the manufacturer's perspective, and assume channel members have the same level of members(Choi, 1996). Results - This paper tries to apply the game theory to researches on how retailers can maximize the benefits of distributing NB(National Brand) products and PB(Private Brand) products, while distributors can also take advantage of their profits. Conclusions - It was found that providing cheap PBs did not help manufacturers and distributors. Distributors and manufacturers' profits were determined by consumers who purchased NB products that were higher in price and higher in perceived quality before providing existing PB products to consumers.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.93-98
• /
• 2000

Unpredictable failures can occur due to the DHC (delayed hydride cracking) or the degradation of fracture toughness by hydride embrittlement in CANDU pressure tube which can result from the absorption of hydrogen or deuterium in the high temperature coolant. To investigate the hydride embrittlement of CANDU Zr-2.5Nb pressure tube, the transverse tensile test and the fracture toughness test were performed from room temperature to $300^{\circ}C$ using three different specimens which have an AR (As Received), 100, and 200 ppm hydrogen. As the amount of absorbed hydrogen was increased, the transverse yield strength and the ultimate tensile strength were also increased. In addition, as the test temperature became higher they were decreased linearly. While, at room temperature, the hydrogenbsorbed specimens represented the embrittlement which resulted in sudden decreasing of fracture toughness, the fracture characteristics became ductile such as AR specimen at high temperatures. Through the observation of fracture surface using SEM, it was found that the stress state of mixed mode could be related to the fissure which was believed to decrease the global fracture toughness.

• 한국재료학회지
• /
• 제12권5호
• /
• pp.369-374
• /
• 2002

To investigate the corrosion behavior of Zr-1.0Nb-xSn (x=1.0, 1.5, 2.0 and 2.5wt. %)alloy system, the corrosion tests of Zr-1.0Nb-xSn alloys were carried out in steam at $400^{\circ}C$ for 125 days and in 70ppm LiOH solution at $360^{\circ}C$ for 180 days. The matrix microstructures of the test specimens were analyzed using TEM and the oxide structures on the test specimens were analyzed using XRD. It was found from the analyses that the more Sn content the alloy had, the faster it was corroded and with the increase of Sn content in the alloy the fraction of $t-ZrO_2$ to $m-ZrO_2$ was decreased. It was also found that the alloys having more Sn showed more dislocation density than those having less.