• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.3
• /
• pp.176-185
• /
• 2006

• Advances in nano research
• /
• v.10 no.5
• /
• pp.493-507
• /
• 2021

This article focused on studying the buckling behavior of two-dimensional functionally graded (2D-FG) nanosize tubes, including porosity based on first shear deformation and higher-order theory of tube. The nano-scale tube is simulated based on the nonlocal gradient strain theory, and the general equations and boundary conditions are derived using Hamilton's principle for the Zhang-Fu's tube model (as higher-order theory) and Timoshenko beam theory. Finally, the derived equations are solved using a numerical method for both simply-supported and clamped boundary conditions. The parametric study is performed to study the effects of different parameters such as axial and radial FG power indexes, porosity parameter, nonlocal gradient strain parameters on the buckling behavior of di-dimensional functionally graded porous tube.

• Structural Engineering and Mechanics
• /
• v.68 no.2
• /
• pp.203-213
• /
• 2018

This paper presents a study of geometric nonlinear forced vibration of carbon nano-tubes (CNTs) reinforcement composite plates on nonlinear elastic foundations. The plate is bonded with piezoelectric layers. The von Karman geometric nonlinearity assumptions with classical plate theory are employed to obtain the governing equations. The Galerkin and homotopy perturbation method (HPM) are utilized to investigate the effect of carbon nano-tubes volume fractions, large amplitude vibrations, elastic foundation parameters, piezoelectric applied voltage on frequency ratio and primary resonance. The results indicate that the carbon nano-tube volume fraction, applied voltage and elastic foundation parameters have significant effect on the hardening response of carbon nanotubes reinforced composite (CNTRC) plates.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.3
• /
• pp.595-601
• /
• 2017

In vivo assay of glucose detection was described using a skin tattoo film electrode (STF), and the probe was made from carbon nano tube paste modification film paper. Here in the square-wave stripping anodic working range obtained of $20-100mgL^{-1}$ within an accumulation time of 0 seconds only in sea water electrolyte solutions of pH 7.0. The relative standard deviations of 50 mg glucose that were observed of 0.14 % (n=12), respectively, using optimum stripping accumulation of 30 sec, the low detection limit (S/N) was pegged at 15.8 mg/L. The developed results can be applied to the detect of in vivo skin sensing in real time. Which confirms the results are usable for in vitro or vivo diagnostic clinical analysis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.211-212
• /
• 2005

Semiconductor fabrication technique has been increasingly developed virtue of greater demands, and supplies and applied semiconductor components in respective processes under development for minuteness. Now semiconductor having a line-width of 75nm was commercialized, and it is possible to scale down to 25nm. Accordingly, to cover with limitations, alternatives are actively investigated. In this paper, we overview the trend and applications of carbon nano tube (CNT) and present the future and technology based on existed theories.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.679-687
• /
• 2014

In this study, a new paint which is able to resist the cavitation erosion is tried to be developed by using urethane added with nano particles such as multi-wall and single-wall carbon nano tube and spherical and fiber type graphite. The new paint synthesized was characterized with physical properties and resistivity to cavitation erosion($t_{50}$). Among nano particles, fiber type graphite($t_{50}$ 292min) showed high hardness and wear resistance compared with spherical type($t_{50}$ 182min). For carbon nano tube, single-wall type($t_{50}$ 286min) was higher than multi-wall type in wear resistance. Fiber-type graphite was the best nano-particle for paint with resistivity to cavitation erosion. In the application test of paint, the manually painted sample showed surface with smooth but the surface of sample prepared with spray was not smooth. During spray, dust was fixed on the surface.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.415-415
• /
• 2012

ZnO nanostructures were synthesized by a vapor phase transport process in a single-zone furnace within a horizontal quartz tube with an inner diameter of 38 mm and a length of 485 mm. The ZnO nanostructures were grown on Au-catalyzed Si(100) substrates by using a mixture of zinc oxide and graphite powders. The growth of ZnO nanostructures was conducted at $800^{\circ}C$ for 30 min. High-purity Ar and $O_2$ gases were pushed through the quartz tube during the process at a flow rate of 100 and 10 sccm, respectively. The sequence of ON/OFF cycles of the Ar gas flow was repeated, while the $O_2$ flow is kept constant during the growth time. The Ar gas flow was ON for 1 min/cycle and that was OFF for 2 min/cycle. The structure and optical properties of the ZnO nanostructures were investigated by field-emission scanning electron microscope, X-ray diffraction, temperature-dependent photoluminescence. The preferred orientation of the ZnO nanostructures was along c-axis with hexagonal wurtzite structure.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.9 s.174
• /
• pp.49-59
• /
• 2005

This paper describes a development of the extrusion process and estimation of the weldability for multi cell tubes used to cooling system of automobiles. A study on extrusion process is performed through the 3D FE simulation in non-steady state and extrusion experimentation. Also, nano-indentation test is employed to estimate the weldability of tubes. Especially, An evaluation of the weldability using the nano-indentation is accomplished as compared with nano-hardness in welded part and in the others. Finally, the pattern of the mandrel defection is investigated according to shapes of the porthole and/or chamber.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.867-869
• /
• 2003

Vacuum tube arrays (VTA) with a submicron dimension were fabricated by using anodic aluminum oxide (AAO) nano-templates. The field emission characteristics of Ni nanowires show a turn-on voltage in the range of 11.0-14.0 V and a field enhancement factor in the range of 560-2790. The distance between the tips of Ni nanowires and the anode was much smaller than that between the tips and the anode of conventional designs.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2005.11a
• /
• pp.100-101
• /
• 2005