• Journal of the Korean institute of surface engineering
• /
• v.39 no.4
• /
• pp.160-165
• /
• 2006

Ni-SiC composite coating layers were prepared by electroplating method and their deposition rate, codeposition of SiC, morphology, surface roughness, hardness, wear and friction properties were investigated. It was found that the deposition rate and the codeposition of SiC in the composite coating layer increased with increasing concentration of SiC in the solution only at the early stage. Both of them reached certain maxima and then decreased with increasing concentration of SiC. Rough surface was obtained with increasing codeposition of SiC, which is probably due to the agglomeration of the SiC particle in the vicinity of surface. Vickers hardness increased with increasing codeposition of SiC and heat treatment at $300^{\circ}C$ in air for 1 hour. Wear volume decreased with increasing codeposition of SiC and friction coefficient increased with increasing codeposition of SiC at the early stage, and it became almost constant. Such wear and friction behaviors are desirable for the practical application.

• Applied Chemistry for Engineering
• /
• v.31 no.2
• /
• pp.215-219
• /
• 2020

In this study, nanoporous iron oxide layers were fabricated by the anodization of 304 series stainless steel. K₂HPO₄/glycerol solution was used as an electrolyte for anodization. We investigated the anodization behavior according to various parameters such as electrolyte concentration, reaction temperature, applied voltage, and reaction time. As a result of anodization, we confirmed that the anodic growth rate of oxide layer on 304 series stainless steel increased with increasing the electrolyte temperature and applied potential. In order to form well-ordered porous nanostructures, the electrolyte temperature was at 160 ℃, and the applied potential was at 30 V in 10 wt% K₂HPO₄/glycerol electrolyte.

• Journal of Radiation Industry
• /
• v.9 no.1
• /
• pp.9-13
• /
• 2015

Epoxy resin is widely used as aerospace, automobile, construction and electronics due to their good mechanical and electrical properties and environmental advantages. However, the inherent flammability of epoxy resin has limited its application in some field where good flame retardancy is required. Nano clay can enhance the properties of polymers such as flames retardancy and thermal stability. In this study, we have investigated the nanoclay filled epoxy composite, which has good flame retardancy while maintaining high mechanical properties. The cured epoxy resins were obtained using an electron beam curing process. The nano clays were dispersed in epoxy acrylate solution and mechanically stirred. The prepared mixtures were irradiated using an electron beam accelerator. The composites were characterized by gel content and thermal/mechanical properties. Moreover, the flammability of the composite was evaluated by limited oxygen index (LOI). The flame retardancy of nano clay filled epoxy composite was evidently improved.

• Korean Journal of Metals and Materials
• /
• v.49 no.1
• /
• pp.79-84
• /
• 2011

Double-walled carbon nanotubes (DWCNTs) with high purity were produced by the catalytic decomposition of tetrahydrofuran (THF) using a Fe-Mo/MgO catalyst at $800^{\circ}C$. The as-synthesized DWCNTs typically have catalytic impurities and amorphous carbon, which were removed by a two-step purification process consisting of acid treatment and oxidation. In the acid treatment, metallic catalysts were removed in HCl at room temperature for 5 hr with magnetic stirring. Subsequently, the oxidation, using air at $380^{\circ}C$ for 5 hr in the a vertical-type furnace, was used to remove the amorphous carbon particles. The DWCNT suspension was prepared by dispersing the purified DWCNTs in the aqueous sodium dodecyl sulfate solution with horn-type sonication. This was then air-sprayed on ITO glass to fabricate DWCNT field emitters. The field emission properties of DWCNT films related to transmittance were studied. This study provides the possibility of the application of large-area transparent CNT field emission cathodes.

• Membrane Journal
• /
• v.18 no.3
• /
• pp.206-213
• /
• 2008

Poly(vinylidene fluoride) (PVDF) membrane surfaces were modified using surface modifying macromolecules (SMMs). The Zonyl BA-L as SMM was used and the various PVDF membranes containing 0 to 2 wt% SMM were prepared. The resulting membranes were characterized through SEM, contact angle measurements and pervaporation separation of water-ethanol system. SMM layers were created in the surface regions of PVDF membranes by SEM images and the contact angles were increased more than untreated PVDF membranes. The pervaporation was carried out at 50, 60 and $70^{\circ}C$, and the PVDF membranes containing 1 and 2 wt% SMM were used for 10, 20, 50 wt% water in the binary water/ethanol mixtures and pure water. PVDF/2 wt% Zrlnyl BA-L membrane showed the permeability 5.3 $g/m^2hr$ and separation factor 287 at $50^{\circ}C$ for water : ethanol = 10 : 50 solution.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1315-1318
• /
• 2004

Nano-scale fabrication of silicon substrate in an aqueous solution based on the use of atomic force microscopy was demonstrated. A specially designed cantilever with diamond tip, allowing the formation of damaged layer on silicon substrate easily by a simple scratching process (Tribo-Nanolithography, TNL), has been applied instead of conventional silicon cantilever for scanning. A slant nanostructure can be fabricated by a process in which a thin damaged layer rapidly forms in the substrate at the diamond tip-sample junction along scanning path of the tip and simultaneously the area uncovered with the damaged layer is being etched. This study demonstrates how the TNL parameters can affect the formation of damaged layer and the shape of 3-D structure, hence introducing a new process of proximal nanolithography in aqueous solution.

• Journal of Powder Materials
• /
• v.9 no.5
• /
• pp.346-351
• /
• 2002

Pure and fine, two-component titanate powders (barium titanate, calcium titanate etc.) were synthesized by an ethylene glycol method. Titanium isopropoxide and other metal ionic salts were dissolved in liquid-type ethylene glycol without any precipitation. In non-aqueous system, the amount of ethylene glycol affected the solubility and homogeneity of metal cation sources in the solution. At the optimum amount of the polymer, the metal ions were dispersed effectively in solution and a homogeneous polymeric network was formed. Most of the synthesized powders had sub-micron or nano-size primary particles after calcination and the agglomerated calcined powders were easily ground by ball milling process. All synthesized titanate powders had stable crystallization behavior at low temperature and high specific surface area after ball milling. The crystallization behavior and the microstructures of the calcined powders were affected on the ethylene glycol content.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.1
• /
• pp.46-48
• /
• 2015

Thin film transistor (TFT) with silicon indium zinc oxide (SIZO) was fabricated by solution process, and the effect of annealling temperature on the electrical performance has been explored. The performance of SIZO TFT exhibited saturation mobility of $1.37cm^2$/Vs, a threshold voltage of -7.2 V, and an on-off ratio of $1.1{\times}10^5$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.537-539
• /
• 2009

We report the improvement in adhesion of IZO thin films through oxygen ($O_2$) plasma treatment of organic polymer film. In conclusion, the $O_2$ plasma treatment of an organic polymer film was accomplished with improving ca. 1.8 times in adhesion than that of the only general etch treatment on the same organic polymer film.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.438-439
• /
• 2006

Pure and stable YAG $(Y_3Al_5O_{12})$ powders were synthesized by a PVA (polyvinyl alcohol) polymer solution technique. PVA was used as an organic carrier for the precursor ceramic gel. The precursor gels were crystallized to YAG at relatively a low temperature of $900\;^{\circ}C$. The synthesized powders, which have nano-sized primary particles, were soft and porous, and the porous powders were ground to sub-micron size by a simple ball milling process. The ball-milled powders were densified to 94% relative density at $1500\;^{\circ}C$ for 1h. In this study, the characteristics of the synthesized YAG powders were examined.