• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.4
• /
• pp.484-489
• /
• 2012

The objective of this work presented here was focused on analysis of particulate matter and nitrogen oxide characteristics in ESC test mode from heavy-duty diesel engine installed on-road vehicles applicable to prime propulsion engine for marine vessels. The authors confirmed that a large quantity particulate matter were emitted in high power density condition, nitrogen oxide characteristics were dependent on exhaust gas temperature. Particulate matters were reduced by 1/100~1/1,000 times in post DPF with test modes but filtration efficiency was decreased in the engine power fluctuation. In the case of the high speed and power condition, the exhaust level of particulate matters was increased according to increment of temperature of gas flowing into DPF. The orders of magnitude for particle concentration levels from the analysis of size distribution of particulate matters of test engine was different. Both emitting nano-sized particles below 100nm regardless of DPF and non-DPF.

• Korean Chemical Engineering Research
• /
• v.57 no.5
• /
• pp.730-734
• /
• 2019

Thermophoresis is a transport phenomenon of particles driven by a temperature gradient of a medium. In this paper, we discuss the thermophoresis of particles in microfluidic channels. In a non-fluidic, stagnant channel, the thermophoretic transport of micro-particles was found to be larger in proportion to the voltage applied to the platinum wire heat source installed in the channel. The variation of the temperature around the platinum wire depending on the voltage was estimated, by using the Callendar-van Dusen equation. The thermophoretic behavior of nano-particles in the same system was observed, which is similar to that of the microparticles. Finally, we fabricated a Y-shaped microfluidic channel with a platinum wire heat source installed in the channel, to realize the thermophoretic phenomenon of the particles in the suspension flowing through the channel. It is shown that the flow of the suspension can be controlled based on the thermophoretic principle.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.3
• /
• pp.593-599
• /
• 2023

Nickel oxide (NiO) nanoparticles were successfully synthesized by a simple liquid phase process for producing ceramics powder using a precursor impregnated with a nickel(II) nitrate hexahydrate aqueous solution in an industrial pulp. The microfibrile structure of the precursor impregnated with nickel nitrate hexahydrate aqueous solution was confirmed by scanning electron microscope (SEM), and the crystal structure and particle size of nickel oxide (NiO) particles produced as the heat treatment temperature of the precursor were analyzed by X-ray diffraction (XRD) and SEM. As a result, it was confirmed through XRD and SEM analysis that the temperature at which the organic material of the precursor is completely thermally decomposed was 495-500℃, and the size and crystallinity of the nickel oxide particles produced increased as the heat treatment temperature increased. The size of the nickel oxide particles obtained by heat treatment at 500-800℃ for 1 hour was 50-200 nm. It was confirmed by XRD and SEM analysis that a NiO crystal phase was formed at a heat treatment temperature of 380℃, only a single NiO phase existed until 800℃.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.3
• /
• pp.212-218
• /
• 2017

$Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrite powders were prepared by self-propagating high temperature synthesis followed by classifying with an ultrasonic wet-magnetic separation unit to get high pure nano-sized particles. The $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrites were well formed by using several powders like iron, nickel oxide, zinc oxide and magnesium oxide at 0.1 MPa of oxygen pressure. The ultrasonic wet-magnetic separation of pre-mechanical milled ferrite powders resulted in producing the powders with average size of 800 nm. The addition of a surfactant during the wet-magnetic separation process improved productivity more than twice. The coercive force, maximum magnetization and residual magnetization of the $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ nano-powders with 800 nm size were 3651 A/m, $53.92Am^2/kg$ and $4.0Am^2/kg$, respectively.

• Journal of the Korean Ceramic Society
• /
• v.42 no.9 s.280
• /
• pp.607-612
• /
• 2005

The effect of MgO diluents in combustion synthesis of $TiB_2$ nano particles was investigated. The reaction $TiO_2\;+\;B_2O_3\;+\;xMg\;{\rightarrow}\;TiB_2\;+\;5MgO$ was used to synthesize $TiB_2$ nano particles. The combustion velocity was measured to examine the relation between the reaction temperature and the morphologies of particles. The diluent MgO did not react with the reactants and played a role to decrease combustion temperature. As the MgO diluents contents increased, the particles with the smaller size and the narrower size distribution were synthesized. At the condition of 6 mole of MgO, the combustion wave velocity was about 5 cm/see and the synthesized particles showed the size of 60 nm with narrow size distribution.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.9
• /
• pp.799-804
• /
• 2014

Hard turning is a machining process for hardened materials with high surface quality so that grinding process can be eliminated. Therefore, the hard turning is capable of reducing machining time and improving productivity. In this study, hardened AISI4140 (high-carbon chromium steel) that has excellent yield strength, toughness and wear resistance was finish turned using CBN tools. Wear characteristics of CBN tool was analyzed in dry and MQL mixed with nano-particle (Nano-MQL). The dominant fracture mechanism of CBN tool is diffusion and dissolution wear on the rake surface resulting in thinner cutting edge. Abrasive wear by hard inclusion in AISI4140 was dominant on the flank surface. Nano-MQL reduced tool wear comparing with the dry machining but chip evacuation should be considered. A cryogenically treated tool showed promising result in tool wear.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.3
• /
• pp.454-460
• /
• 2015

The present study is undertaken to evaluate the effect of volume fraction on the results of Charpy impact test for the rubber matrix filled with nano sized silica particles composites. The Charpy impact tests are conducted in the temperature range $0^{\circ}C$ and $-10^{\circ}C$. The range of volume fraction of silica particles tested are between 11% to 25%. The critical energy release rate $G_{IC}$ of the rubber matrix composites filled with nano sized silica particles is affected by silica volume fraction and it is shown that the value of $G_{IC}$ decreases as volume fraction increases. In regions close to the initial crack tip, fracture processes such as matrix deformation, silica particle debonding and delamination, and/or pull out between particles and matrix which is ascertained by SEM photographs of Charpy impact fracture surfaces.

• KSBB Journal
• /
• v.28 no.4
• /
• pp.249-253
• /
• 2013

In this study, we analyzed the attachment amount and the surface properties, such as shape and attachment aspect of silver nanoparticles on the surface of salt and sucrose. In addition, we investigated the antimicrobial activity of silver nanoparticles by measuring total colony counts and total coliforms in sewage according to the time and the amount of silver nanoparticles. As a result, it is found that silver nanoparticles are attached on the surface of salt and sucrose from the SEM images and there is no microorganisms on the surface of salt and sucrose. Silver nanoparticles on salt were rod shape but silver nanoparticles on sucrose were round shape. Also, the content of silver was 0.735 mg/g on salt and 0.885 mg/g on sucrose. In all experiments, total colony counts and total coliforms sharply declined initially, and it decreased gradually as change the time. When injection amount of nano silver sucrose and salt increased, the width of decline was greater. The amount of total colony counts and total coliforms of nano silver salt was much lower and the disinfection efficiency was higher comparing with nano silver sucrose. That means the case of nano silver salt is much better at the antimicrobial activity.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.7
• /
• pp.549-555
• /
• 2006

In the present study, sterilizing and antibacterial performance tests of Polybutylene pipe with nano-silver were carried out in the testing bench of water supply facilities. Experimental results show that the average sterilizing and antibacterial rate of two micro-biological samples such as E. coli and S. aureus is about 90% in case of stillness experimental condition and 99% in case of flowing experimental condition, when elapsed time is 120 hours and 3 hours, respectively. Experimental results also show that the supply water velocity in nano-silver Polybutylene pipe varies from 1 m/s to 1.5 m/s, the elapsed time needed sterilizing rate reach to 100% decreases.

• Journal of Powder Materials
• /
• v.15 no.2
• /
• pp.148-155
• /
• 2008

Nano magnetite particles have been prepared by two step reaction consisting of urea hydrolysis and ammonia addition at certain ranges of pH. Three different concentrations of aqueous solution of ferric ($Fe^{3+}$) and ferrous ($Fe^{2+}$) chloride (0.3 M-0.6 M, and 0.9 M) were mixed with 4 M urea solution and heated to induce the urea hydrolysis. Upon reaching at a certain pre-determined pH (around 4.7), 1 M ammonia solution were poured into the heated reaction vessels. In order to understand the relationship between the concentration of the starting solution and the final size of magnetite, in-situ pH measurements and quenching experiments were simultaneous conducted. The changes in the concentration of starting solution resulted in the difference of the threshold time for pH uprise, from I hour to 3 hours, during which the akaganeite (${\beta}$-FeOOH) particles nucleated and grew. Through the quenching experiment, it was confirmed that controlling the size of ${\beta}$-FeOOH and the attaining a proper driving force for the reaction of ${\beta}$-FeOOH and $Fe^{2+}$ ion to give $Fe_3O_4$ are important process variables for the synthesis of uniform magnetite nanoparticles.