• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.475-475
• /
• 2017

본 연구는 급변하는 기후변화에 대응하기 위한 이동식 전처리 여과취수장치 및 이를 이용한 물 생산용 취수시스템에 관한 것으로 홍수시나 가뭄시 이물질과 부유물질의 제거를 통해 후속 여과 장치의 부하 경감과 여과 효율의 극대화를 꾀할 수 있고, 필요시 비상용수 및 생활용수로 신속히 활용할 수 있는 시설에 관한 것이다. 기존 이동식 물생산장치의 수처리 공정은 1NTU 내외의 깨끗한 물이 유입되지 않으면 여과기(RO SYSTEM) 막이 폐색되어 생산된 물의 수질이 일정치 않아 재난 시 활용하는데 어려움이 있었다. 반면에 본 연구의 물 생산용 취수시스템은 전처리 여과취수를 통해 이물질과 부유물질의 제거가 가능하여 후속 여과 장치의 부하 경감을 통해 유지관리비용 최소화와 여과 효율의 극대화를 꾀할 수 있고, 필요시 신속히 생활용수로 활용할 수 있으며, 다양한 급수원(하천, 저수지, 댐, 지하수 등)을 통한 수량 확보가 가능하고, 평상시 다용도(하천정화, 녹조제거, 도로 청소, 조경수 등)로 사용이 가능한 물생산시스템이다. 또한, 비상시 이동식 차량에 탑재하여 이동 및 운반이 가능할뿐만 아니라 저수지나 댐 또는 하천 등의 원수를 취수하여 이중 관 구조의 여과기를 통한 전처리로 지속적인 여과력을 발휘하여 이물질이나 부유물질을 신속히 제거하고, 역세척수 공급으로 여과재를 쉽게 역세척할 수 있어 여과 성능의 저하를 방지할 수 있다. 본 연구에서의 이동식 전처리 여과취수장치는 다양한 조건에서의 수치모의를 수행하여 평상시나 비상시 다용도의 필요수량을 확보할 수 있도록 장치의 최적화를 수행하였으며, 이를 통해 안정적인 수자원 확보와 활용이 가능하고, 국내 물 시장에서 물생산시스템의 다양성을 확보하여 국민경제에 기여할 수 있고, 향후 물 부족 국가의 ODA 사업에 진출하여 수출증대 효과를 얻을 수 있을 것이다.

• Environmental Engineering Research
• /
• v.24 no.2
• /
• pp.263-270
• /
• 2019

Palm oil mill effluent (POME) is the largest pollutant discharged into the rivers of Malaysia. Thus UF membrane study was conducted to investigate the effect of pressure and stirring speed on performance of POME treatment and fouling of membrane. Two types of membrane polyethersulfone (PES) and regenerated cellulose (RC) with molecular weight cut-off (MWCO) 5 and 10 kDa were used in this study. Results showed that, as pressure increased, fouling increased however permeate quality improved, the best pressure was 1.0 bar, where the fouling was not too high and produce good permeate quality. As stirring speed increased, fouling reduced and permeate quality improved, however, when stirring speed increased from 600 rpm to 800 rpm, there was no significant improvement on the permeate quality. Therefore, the best condition was at 1.0 bar and 600 rpm. PES membrane with MWCO 5 kDa showed the best permeate quality, even fouling slightly higher than RC membrane. The permeate quality obtained were analyzed in term of dissolved solid, turbidity, suspended solid, biological oxygen demand ($BOD_5$) and chemical oxygen demand (COD) were 538 mg/L, 1.02 NTU, < 25 mg/L, 27.7 mg/L and 62.8 mg/L, respectively with dominant type of fouling is cake resistance. Thus, it can be concluded water reuse standard was successfully achieved in terms of $BOD_5$ and suspended solid.

• Journal of Environmental Science International
• /
• v.28 no.3
• /
• pp.291-301
• /
• 2019

This study was conducted to investigate the effect of salt concentration and turbidity on the inactivation of Artemia sp. by electrolysis, UV photolysis, electrolysis+UV process to treat ballast water in the presence of brackish water or muddy water caused by rainfall. The inactivation at different salt concentrations (30 g/L and 3 g/L) and turbidity levels (0, 156, 779 NTU) was compared. A decrease in salt concentration reduced RNO (OH radical generation index) degradation and TRO (Total Residual Oxidant) production, indicating that a longer electrolysis time is required to achieve a 100% inactivation rate in electrolysis process. In the UV process, the higher turbidity results in lower UV transmittance and lower inactivation efficiency of Artemia sp. Higher the turbidity resulted in lower ultraviolet transmittance in the UV process and lower inactivation efficiency of Artemia sp. A UV exposure time of over 30 seconds was required for 100% inactivation. Factors affecting inactivation efficiency of Artemia sp. in low salt concentration are in the order: electrolysis+UV > electrolysis > UV process. In the case of electrolysis+UV process, TRO is lower than the electrolysis process, but RNO is more decomposed, indicating that the OH radical has a greater effect on the inactivation effect. In low salt concentrations and high turbidity conditions, factors affecting Artemia sp. inactivation were in the order electrolysis > electrolysis+UV > UV process. When the salt concentration is low and the turbidity is high, the electrolysis process is affected by the salt concentration and the UV process is affected by turbidity. Therefore, the synergy due to the combination of the electrolysis process and the UV process was small, and the inactivation was lower than that of the single electrolysis process only affected by the salt concentration.

• Journal of Korean Society of Water and Wastewater
• /
• v.35 no.1
• /
• pp.1-14
• /
• 2021

Eutrophication and algal blooms can lead to increase of taste and odor compounds and health problems by cyanobacterial toxins. To cope with these eco-social issues, Ministry of Environment in Korea has been reinforcing the effluent standards of wastewater treatment facilities. As a result, various advanced phosphorus removal processes have been adopted in each wastewater treatment plant nation-widely. However, a lot of existing advanced wastewater treatment processes have been facing the problems of expensive cost in operation and excessive sludge production caused by high dosage of coagulant. In this study, the sedimentation and dissolved air flotation (SeDAF) process integrated with sedimentation and flotation has been developed for enhanced phosphorus removal in wastewater treatment facilities. Design and operating parameters of the SeDAF process with the capacity of 100 ㎥/d were determined, and a demonstration plant has been installed and operated at I wastewater treatment facility (located in Gyeonggi-do) for the verification of field applicability. Several empirical evaluations for the SeDAF process were performed at demonstration-plant scale, and the results showed clearly that T-P and turbidity values of treated water were to satisfy the highest effluent standards below 0.2 mg/L and 2.0 NTU stably for all of operation cases.

• Journal of Korean Society of Water and Wastewater
• /
• v.34 no.6
• /
• pp.463-471
• /
• 2020

A 1,000 ㎥/d DAF(dissolved air flotation) pilot plant was installed to evaluate the performance of the floating process using the Nakdong River. Efficiency of various DAF operations under different conditions, such as hydraulic loading rate, coagulant concentration was evaluated in the current research. The operation conditions were evaluated, based on the removal or turbidity, TOC(total organic carbon), THMFP(trihalomethane formation potential), Mn(manganese), and Al(aluminum). Also, particle size analysis of treated water by DAF was performed to examine the characteristics of particles existing in the treated water. The turbidity removal was higher than 90%, and it could be operated at 0.5 NTU or less, which is suitable for the drinking water quality standard. Turbidity, TOC, and THMFP resulted in stable water quality when replacing the coagulant from alum to PAC(poly aluminum chloride). A 100% removal of Chl-a was recorded during the summer period of the DAF operations. Mn removal was not as effective as where the removal did not satisfy the water quality standards for the majority of the operation period. Hydraulic loading of 10 m/h, and coagulant concentrations of 40 mg/L was determined to be the optimal operating conditions for turbidity and TOC removal. When the coagulant concentration increases, the Al concentration of the DAF treated water also increases, so coagulant injection control is required according to the raw water quality. Particle size distribution results indicated that particles larger than 25 ㎛ showed higher removal rates than smaller particles. The total particel count in the treated water was 2,214.7 counts/ml under the operation conditions of 10 m/h of hydraulic loading rate and coagulant concentrations of 60 mg/L.

• Journal of Environmental Science International
• /
• v.33 no.4
• /
• pp.269-277
• /
• 2024

Scientific forensic techniques are used to verify environmental impact of groundwater pollution, surface water pollution, air pollution, noise, and vibration according to residents' complaints in connection with construction and civil engineering works. In this study, we investigated the contamination of groundwater and the lowering of the groundwater level in an area surrounding a tunnel excavation site for the Andong-Yeongdeok national road, using a forensic hydrogeological technique. We reviewed the groundwater level and water quality of well GW1 in the area surrounding the tunnel excavation site as well as tunnel construction information and then we analyzed the correlations among the obtained data. Before tunnel excavation, the water level of well GW1 was lower than the tunnel elevation. Considering the relationship between the precipitation, tunnel discharge, tunnel depth, and groundwater level of well GW1, the groundwater flowed from the tunnel to well GW1. Moreover, the tunnel discharge and groundwater levels were not related to each other. The pH of well GW1 was 8.4 before tunnel excavation. During excavation, the pH declined to 8.1-8.2 at the beginning, and increased to 8.8 at the end of the excavation. The fluorine concentration in well GW1 was 2.49 mg/L, 1.91-3.22 mg/L, and 1.7-2.67 mg/L, respectively, before, during, and after the excavation. The sulfate ion concentration was very high, over 2,000 mg/L, before and during the excavation; after the excavation, it was between 200 and 323 mg/L. Turbidity was 1.47, 10.5, and 4.51 NTU before, during, and after tunnel excavation, respectively. Therefore, the excavation of this tunnel is not related to the groundwater quality of well GW1.

• Journal of Food Hygiene and Safety
• /
• v.15 no.4
• /
• pp.328-333
• /
• 2000

This study was carried out to changes in chemical and microbiological properties of spring waters in Tongyeoung area. In this paper, ninety spring water samples were collected from 9 station for 11 month to evaluated chemical and bacteriological water quality. Range and mean values of constituents of the samples are as followed; water temperature 5.2~25.8$^{\circ}C$, 16.3$^{\circ}C$, pH 6.0~7.2, 6.7, total residue 33.6~210 mg/1, 90.6 mg/1, turbidity 0.35~5.48, 1.45NTU, KMnO4 consumed 0.51~4.21 mg/1, 1.39 mg/1, chloride ion 6.23~42.5, 16.7 mg/l, phosphate-phosphorus ND-0.04, 0.02 mg/1, nitrite-nitrogen ND~0.02, 0.01 mg/1, nitrate-nitrogen ND~3.56, 1.42 mg/1, ammonia-nitrogen ND~0.20, 0.14 mg/1, dissolved total nitrogen ND~3.78, 1.57 mg/1, iron 0.04~0.28, 0.13ppm, zinc 0.03~0.66, 0.20ppm, mangan ND~0.01, allumium 0.14~0.58, 0.39ppm, copper ND~0.01, 0.01, lead ND~0.01, 0.01ppm, Arsenic ND~0.01, 0.01ppm, mercury ND~0.02, chrome not detected, cadmium not detetced respectively. The viable cell counts of the spring waters ranged 5.0~760/m1(means 130/m1). Range and mean value of total coliform and focal coliform MPN's of the spring waters were 0~2,400MPN/100 ml, 73MPN/100 ml and 0~540MPN/100 ml, 21MPN/100 ml. Spring water quality was usually poor with viable cell counts exceeding 130 CFU/liter and the coliform counts in spring waters of 73 MPN/liter. Composition of coliform by IMViC reaction was 33.3% E. coli, 15.6% Citrobacter freundii, 35.6% Klebsiella aerogenes and others.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.4
• /
• pp.263-271
• /
• 2009

This study evaluated the flocs forming characteristics in the mixing zone to increase the coagulation effect in the drinking water plant. As a measuring tool of formed flocs, on-line particle dispersion analyzer (iPDA) was used in Y drinking water plant. To evaluate the forming flocs, many parameters such as poly amine, coagulant dosing amount, raw water turbidity, and pH was applied in this study. During the periods of field test, poly aluminium chloride (PACl) as a coagulant was used. With the increase of the raw water turbidities, poly amine was also added as one of aids for increasing in coagulation efficiency. The turbidity and pH of raw water was ranged from 7 to 9 and from 25 to 140 NTU, respectively. The increasing of raw water turbidity brought the bigger floc sizes accordingly. From a regression analysis, $R^2$ value was 0.8040 as a function of T, raw water turbidity. Floc size index (FSI) was obtained from a correlation equation as follows; FSI = 0.9388logT - 0.3214 Also, polyamine gave the bigger flocs the moment it is added to the coagulated water in the rapid mixing zone. One of parameters influencing the floc sizes was the addition of powdered active carbon(PAC) in the mixing zone. In case of higher turbidity of raw water, $R^2$ value was 0.9050 in the parameters of [PACl] and [PAC]; FSI = $0.0407[T]^{0.324}[PACI]^{0.769}[PAC]^{0.178}$ On-line floc monitor was beneficial to evaluate the flocs sizes depending on the many parameters consisting raw water properties, bring the profitable basic data to control the mixing zone more effectively.

• Korean Journal of Ecology and Environment
• /
• v.37 no.4 s.109
• /
• pp.411-422
• /
• 2004

A limnological survey was conducted in a reservoir, Lake Hoengsung located in Kangwondo, Korea, from July 2000 to September 2001 on the monthly basis. Phosphorus loading from the watershed was estimated by measuring total phosphorus concentration in the main tributary. Secchi disc transparency, epilimnetic (0-5 m) turbidity, chlorophyll a (Chl-a), total phosphorus (TP), total nitrogen(TN) and silica concentration were in the range of 0.9-3.5 m, 0.1-8.5 NTU, 0.3-32.4 mgChl $m^{-3}$, 5-46 mgP $m^{-3}$, 0.83-3.55 mgN $L^{-1}$ and 0.5-9.6 mgSi $L^{-1}$, respectively. Green algae and cyanobacteria dominated phytoplankton community in warm seasons, from July through October, 2000. In July a green alga (Scenedesmus sp.) was dominant with a maximum cell density of 10,480 cells mL. Cyanobacteria (Microcystics sp.) dominated in August and September with cell density of 3,492 and 295 cells mL ,respectively. Species diversity of phytoplankton was highest (2.22) in July. The trophic state of the reservoir can be classified as eutrophic on the basis of TP, Chl-a, and Secchi disc transparency. Because TP concentration was high in flood period, most of phosphorus loading was concentrated in rainy season. TP loading was calculated by multiplying TP and flow rate. The dam managing company measured inflow rate of the reservoir daily, while TP was measured by weekly surveys. TP of unmeasured days was estimated from the empirical relationship of TP and the flow rate of the main tributary; $TP=5.59Q^{0.45}\;(R^2=0.47)$. Annual TP loading was calculated to be 4.45 tP $yr^{-1}$, and the areal P loading was 0.77 gP $m^{-2}\;yr^{-1}$ which is similar to the critical P loading for eutrophication by Vollenweider's phosphorus model, 0.72 gP $m^{-2}\;yr^{-1}$.

• Korean Journal of Ecology and Environment
• /
• v.41 no.2
• /
• pp.206-215
• /
• 2008

Temporal and spatial distributions of salinity, temperature, dissolved oxygen (DO), and turbidity were investigated at seven sites in the upper regions of brackish Lake Sihwa with a limited water exchange, from March to October 2005. During the study period, salinity and temperature varied $0.1{\sim}29.9\;psu$ and $4.7{\sim}28.1^{\circ}C$, respectively, depending on seasons and sites sampled. A distinct halocline profile showing the maximum density gradient (difference over $20\;psu\;m^{-1}$ between surface and bottom layers) was observed during the rainy season, due to the decrease of salinity in surface layers by freshwater inflow. This result implies that rainfall event is the important factor forming the halocline. On the other hand, the depth and location of haloeline varied with the amount of seawater through the sluice gates and the operation systems (inflow or outflow). High DO (over 300% saturation) was observed at surface layer above the halocline in April when red tide occurred, whereas low DO (below 20% saturation) was at the bottom layer below the halocline in the rainy season. Turbidity ranged $1.5{\sim}80.3\;NTU$ showing the maximum turbidity at the layers above or upper the halocline. As a result, the distributions of DO and turbidity in the upper regions of brackish Lake Sihwa were largely affected by the variation of salinity. Also, when the halocline was formed, the water quality between upper and lower water layers may be expected completely different. This study suggests that the physicochemical characteristics of water in the brackish regions are closely associated with the causes of eutrophication such as red tide and DO deficit.