• Structural Engineering and Mechanics
• /
• v.44 no.2
• /
• pp.239-255
• /
• 2012

This work presents a contribution to understand the inverted trussed beams behavior. The system has a main beam and struts with rectangular cross section associated to a wire rope enlaced to the main beam. It is an unpublished system with the advantage of easy positioning of the wire rope, once it is a continuous and connected by turnbuckles. It is a system that can be used as support for concrete formworks or for rehabilitation wooden beams proposal. The enlacement of the cable demands a small notch at the top of the cross section and a cross pin at the bottom. Six inverted trussed beams were tested, with spans of 180 cm with cables diameter of 1/4". Additionally, four simple beams without any external steel cable were also tested with material from the same lot of wood, allowing a comparison in rupture. The results showed capacity gain of around 60% compared to a simple beam. Once the wire rope characteristics and anchoring are very important for structure response, some improvement suggestions for the efficiency of the cables are also presented.

• Journal of Welding and Joining
• /
• v.10 no.1
• /
• pp.43-51
• /
• 1992

The plastic zone formed around a notch tip is important in analyzing the fracture toughness of structures and particularly weld cracks existed in the weld HAZ (heat affected zone) which produces local plastic deformation at the crack tip. Therefore, in order to analyze the fracture toughness in weld HAZ, it is necessary to investigate the new fracture toughness parameter $K_{c}$ $^{*}$ and critical plastic strain energy $W_{p}$ $^{c}$ according to the shape and size of the plastic zone. 1) If the temperature corresponding to $K_{c}$ $^{*}$=130kg-m $m^{-3}$ 2/ is determined, transition temperature $T_{tr}$ the magnitude of plastic zone size, and heat input change depending on the fracture toughness. The blunted amounts of the parent and weld HAZ show mild linear variation until .delta.=0.4mm and then increase very steeply there after. 2) The relation between the plastic strain energy( $W^{p}$ ) and transition temperature( $T_{*}$tr) in parent metal is more sensitive than that of weld HAZ. However, the plastic strain energy depends on the transition temperature, and thus the yield stress, .sigma.$_{ys}$ becomes an important parameter for plastic strain energy. 3) The critical plastic strain energy( $W_{p}$ $^{c}$ ) absorbed by the plastic zone at the notch tip indicated in case of parent metal: 60J/mm, in case of heat input(20KJ/cm): 75J/mm, in case of heat input(30KJ/cm); 50J/mmJ/mm.

• Journal of Veterinary Clinics
• /
• v.34 no.6
• /
• pp.459-462
• /
• 2017

A 3-year-old, 5.6 kg, castrated, male, British short hair cat presented with subtle weight-bearing lameness of the right hindlimb when walking suddenly after rest. On physical examination, the patient experienced pain when the right stifle joint was hyperextended. There was no clinical improvement of lameness or pain of the right hindlimb, despite the administration of analgesic drugs for one week. During diagnostic arthroscopy of right stifle, mild synovitis and cranial cruciate ligament (CCL) impingement on osteophyte of the intercondylar notch (ICN) was observed. Computed tomography was applied to determine an accurate surgical plan. Arthroscopy-assisted notchplasty, including removal of the osteophyte, was performed using chisel and arthroscopic burr. At 4 weeks postoperatively, the frequency of subtle weight-bearing lameness of the right hindlimb was significantly reduced. At 6 months postoperatively, the patient exhibited normal ambulation without recurrence of lameness. Impingement of CCL may cause subtle lameness and pain. Arthroscopy can be a good diagnostic tool for early-stage CCL disease. Notchplasty can be recommended for osteophyte-induced CCL disease.

• Nuclear Engineering and Technology
• /
• v.52 no.7
• /
• pp.1579-1586
• /
• 2020

Dissimilar metal joints (DMJs) are more common in the application of piping system of many industries. A 2- D and 3-D finite element analysis (FEA) is carried out on dissimilar metal Single Edged Notch Bending (DMSENB) specimens fabricated from ferritic steel, austenitic steel and Inconel - 182 alloy to study the behavior of DMJs with constraints by using linear elastic fracture mechanics (LEFM) principles. Studies on DMSENB specimens are conducted with respect to (i) dissimilar metal joint width (DMJW) (geometrical constraints) (5 mm, 10 mm, 20 mm, 30 mm and 50 mm) (ii) strength mismatch (material constraints) and (iii) crack lengths (16 mm, 20 mm and 24 mm) to study the DMJ behavior. From the FEA investigation, it is observed that (i) SIF increases with increase of crack length and DMJWs (ii) significant constraint effect (geometry, crack tip and strength mismatch) is observed for DMJWs of 5 mm and 10 mm (iii) stress distribution at the interfaces of DMSENB specimen exhibits clear indication of strength mismatch (iv) 3-D FEA yields realistic behavior (v) constraint effect is found to be significant if DMJW is less than 20 mm and the ratio of specimen length to the DMJW is greater than 7.4.

• Tunnel and Underground Space
• /
• v.19 no.4
• /
• pp.366-372
• /
• 2009

Recently, in order to achieve smooth fracture plane and minimize the excavation damage zone in rock blasting, controlled blasting methods which utilize new technologies such as electronic delay detonator (EDD) and a notched charge hole have been suggested. In this study, smooth blastings utilizing three wing type notched charge holes are simulated to investigate the influence of explosive initial density on the resultant fracture plane and damage zone using dynamic fracture process analysis (DFPA) code. Finally, based on the dynamic fracture process analyses, novel smooth blasting method, ED-Notch SB (Electronic Detonator Notched Charge Hole Smooth Blasting) is suggested.

• Journal of Welding and Joining
• /
• v.14 no.4
• /
• pp.89-98
• /
• 1996

This study was performed to establish the characteristics of the heat affected zones from view point of the repair weldability for a damaged CrMoV steam turbine rotor steel. Characterization of the heat affected zones of the weldment was conducted with respect to various of postweld heat treatment temperatures, $566^{\circ}C$, $621^{\circ}C$ and $677^{\circ}C$. The evaluations of the heat affected zones were carried out in terms of microstructural characterization, microhardness measurements, Charpy v-notch impact, tensile and stress-rupture tests. The results indicated that the effect of the postweld heat treatment at $677^{\circ}C$ exhibited the favorable microstructure and mechanical properties for the stability of the heat affected zones. While the heat affected zone of the weldment, produced without postweld heat treatment, displayed the inferior toughness and microstructure indicating localized carbide precipitations on the grain boundary. It was also indicated that the stability of the heat affected zones were deteriorated by the formation of the cavitation on the grain boundaries.

• Restorative Dentistry and Endodontics
• /
• v.15 no.1
• /
• pp.20-32
• /
• 1990

The plane strain fracture toughness of a material characterize the resistance to fracture in the presence of a sharp crack under severe tensile condition. Fracture toughness can be determined by indentation method. The purpose of this study was to investigate the fracture toughness of dental amalgams by measuring the plane strain fracture toughness and the fracture toughness from indentation method. Two conventional and four high copper amalgam alloys were employed for this study. The amalgams were prepared according to the A.D.A. spec. No. 1 and inserted into the specially designed mould with the single edge notch specimen to use in 3-point bending method. The specimens (20mm long, 4mm wide, 2mm thick) were stored at $37^{\circ}C$ for 1 week, and tested in 3-point bending by means of Instron at a cross-head speed of 1mm/min. In indentation method, the specimens were made in same manner as single edge notch specimens. The test was conducted with Vickers hardness tester at 10kg load. The following results were obtained. 1. The plane strain fracture toughness and the fracture toughness from indentation method were higher in the low copper amalgams than the high copper amalgams. 2. In high copper amalgams, the fracture toughness of amalgams decreases according as the copper contents increase. 3. In similar copper contents, the single composition amalgams have a higher fracture toughness than the admixed amalgams.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.4
• /
• pp.215-221
• /
• 2009

The objectives of this paper are to measure the heat transfer and pressure drop of the heat transfer tube for an evaporator of absorption system applications. Five types of heat transfer tubes with different shape and heat transfer area are tested in the present experiment. Heat transfer and pressure drop performance of heat transfer tubes are measured in various operating conditions, and compared each other. The results show that the heat transfer coefficient of thermoexcel notch tube increases about 79.6% and 45.3% at the film Reynolds number 69.7 compared with that of bare tube and low fin tube, respectively. The thermoexcel notch tube is show the best performance considering pressure drop and heat transfer coefficient.

• Korean Journal of Veterinary Service
• /
• v.42 no.2
• /
• pp.117-120
• /
• 2019

Bovine viral diarrhea Virus (BVDV) infections cause respiratory, gastrointestinal, and reproductive problems, such as infertility, abortion, stillbirth, and sickly offspring. Many countries have reduced the economic damage through the application of different control programmes, and some have successfully eradicated BVD. Detection and elimination of cattle persistently infected (PI) with BVDV is important for BVD eradication because PI cattle are a main source of BVD transmission. In this study, the prevalence of Korean native cattle persistently infected (PI) with BVDV was investigated and determined in 49 farms with 3,050 cattle. The all samples were collected by ear notch sampling. Korean native cattle with initial positives on antigen-ELISA (Ag-ELISA) were sampled again after 3~4 weeks and cattle with second positives in both Ag-ELISA and immunohistochemistry (IHC) were identified as PI cattle. Among the 49 farms, 14 (28.6%) farms had at least more than one PI cow and 21 (0.69%) of 3,050 cattle were determined as PI cattle. As a result of this work, it is suggested that national BVD eradication program is required to reduce economic losses by BVDV infection in Korean cattle industries.

• International Journal of Internet, Broadcasting and Communication
• /
• v.16 no.1
• /
• pp.330-338
• /
• 2024

In this paper, a Ka-band high-output active phased array antenna device applicable to small radars and seekers was designed, and the improved performance was studied. The radiation device assembly consists of 1x8 arrangements, and the step flared notch antenna type. It shows low active reflection loss characteristics in broadband, and low loss characteristics by applying the air-strip feeding structure, and is designed to enable beam steering up to 45 degrees. The TRM(transmit receive module) output power is more than 2.0W per channel using GaN HPA in the transmitting path, and satisfies more than 25.0 dB gain and less than 6.0 dB noise figure in the receiving path. Accordingly, the Effective Isotropically Radiated Power(EIRP) of the antenna unit shows the performance of 0.00 dB or more and the receive gain-to-noise temperature ratio(G/T) of 0.00 dB/k or more. For demonstration, we have designed aforementioned planar array antenna which consists of 64 radiating elements having a size within 130 mm x 130 mm x 300 mm and weight of less than 4.9 kg..