• 한국정밀공학회지
• /
• 제11권6호
• /
• pp.28-41
• /
• 1994

An efficient algorithm is proposed to select the proper tools and generate their paths for NC rough cutting of dies and molds with sculptured surfaces. Even though a milling process consists of roughing, semi-finishing, and finishing, most material is removed by a rough cutting process. Therfore it can be said that the rough cutting process occupy an important portion of the NC milling process, and accordingly, an efficient rough cutting method contributes to an efficient milling process. In order work, the following basic assumption is accepted for the efficient machining. That is, to machine a region bounded by a profile, larger tools should be used in the far inside and the region adjacent to relatively simple portion of the boundary while smaller tools are used in the regions adjacent to the relatively complex protion. Thus the tools are selected based on the complexity of the boundary profile adjacent to the region to be machined. An index called cutting path ratio is proposed in this work as a measure of the relative complexity of the profile with respect to a tool diameter. Once the tools are selected, their tool paths are calculated starting from the largest to the smallest tool.

• 한국정밀공학회지
• /
• 제20권9호
• /
• pp.13-19
• /
• 2003

• 열처리공학회지
• /
• 제18권1호
• /
• pp.29-40
• /
• 2005

Formation of nanocrystalline ferrite was investigated using milled powders obtained by planetary ball milling of chips, which were made by high speed mechanical cutting of a low carbon steel(0.15%C-1.1%Mn-0.01%Ti). After 4 hour milling the chips were changed to powders of $50{\mu}m$ in average size, and with increasing milling time the powders were refined to about $3{\mu}m$ for 128 hour and showed more equiaxed shapes. Nanocrystalline(nc) region appeared in the surfaces of powders milled for 1 hour, and the 4 hour milled powders were almost filled with nc region. Hardness of nc region was much higher than that of work-hardened(WH) region. With increasing milling time, ferrite and cementite in pearlite were severely deformed and lamellar spacing was decreased, and then cementites began to disappear after 4 hour milling due to dissolution into ferrite. Deformation bands formed in lightly work-hardened region showed large width and similar crystallographic orientations. Spacing of deformation bands was decreased with deformation and the layered microstructure consisting of narrow deformation bands subdivided into variously oriented small grains was formed by more deformation, and eventually this structure seemed to be evolved to the nc structure by further deformation. It is also conjectured the growth of nc ferrite grains occurred through the coalescence of nanocrystalline ferrites rather than the nucleation and growth of recrystallized grains.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.453-454
• /
• 2006

This paper describes a processing verification technique for developing about end-milling cutters. Developed software is processing verification module for manufacturing. By using cutting simulation method, we can obtain center points of finding wheel via Boolean operation between a grinding wheel and a cylindrical workpiece. The obtained CL data can be used for calculating NC data. After then, we can simulate by using designed grinding machine and NC data. This research has been implemented on a commercial CAD system by using the API function programming. The operator can evaluate the cutting simulation process and reduce the time of design and manufacturing.

• 한국정밀공학회지
• /
• 제16권11호
• /
• pp.197-203
• /
• 1999

Increasing demands on precision machining have necessitated the tool to move not only position error as small as possible, but also with smoothly varying feedrates. Because of the lack of accurate and efficient algorithms for generation of 3-dimensional lines and circles, a full accomlishment for available machine tool resolution is generally unavailable. In this paper, a reference-pulse type 3-axis PC_NC milling system is developed for the precision machining of complex shapes in 3-dimensional space. Three AC servomotors are used as the actuator instead of the hand wheel to operate a 3-axis milling machine under the same mechanical structure. A PC is used to handle the control signal calculation for various types of motion command. To achieve the synchronous 3-axis motion, a real-time reference-pulse 3-dimensional linear and circular interpolator based on the intersection criteria is developed in software. The performance test via computer simulation and actual machining have shown that the PC-NC milling system is useful for the machining of arbitrary lines and circles in 3-dimensional space.

• 한국정밀공학회지
• /
• 제19권12호
• /
• pp.86-92
• /
• 2002

This paper presents a new model of NC verification in NC milling using z-map. The model can describe the motion of machine tool like a real machine effectively. The model uses x, y, and z directional feed rate as well as cutting data for modeling Z-map of workpiece. The model verifies the over-cut, the under-cut and the surface topography using NC codes and cutting conditions. To investigate the performance of the model, simulation study was carried out. As the results, the model gave the geometry accuracy of workpiece, the surface topography, and the chip loads.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.1096-1101
• /
• 1992

In order tominimize fixing error of workpieces, circle, prismatic, sphere, cylindrical and sculptures types. Modification Rule by Indexing Table and Modification Rule by NC Program are developed for machining centers by using touch trigger probes. The Modification Rule by Indexing Table meas the alignment of workpiece to NC program through degree of freedoms of indexing table. The Modification Rule by NC Program is the alognment of NC program to workpiece ste-tp condition via the generation of NC progarm. A postprocessing module is alos developed for generating NC-part program(User Macro) to compensate for machining errors in end milling and boring processes. Developed method are verified by experiments.

• 대한기계학회논문집
• /
• 제19권9호
• /
• pp.2089-2104
• /
• 1995

A novel and efficient cutter path planning method for machining intricately shaped curved surfaces, called the steepest directed tree method, is presented. The curved surface is defined by triangular facets, the density and structure of which are determined by the intricacy and form accuracy of the surface. Geometrical form definition and recognition of the topological features are used to connect the nodes of the triangulated surface meshes for the successive and interconnected steepest pathways, which makes good use of end milling characteristics. The planetary cutter centers are determined to locate along smoothly changing paths and then the height values of the cutter are adjusted to avoid surface interference. Several machined examples of intersecting and intricate surfaces are presented to illustrate the benefits of the new approach. It is shown that due to more consistent geometry matching between cutter and surface(in comparison with the current CC Cartesian method) surface finish can be typically improved. Moreover, the material in concave fillets which is difficult to be removed by ball mills can be removed efficiently. The built-in positioning of cutter to avoid interference runs minutely in the sharp and discontinuous regions. The steepest upward movement of the cutter gives a stable dynamic cutting state and allows increase in the feedrate and spindle speed while remaining the stable cutting state.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1987년도 한국자동제어학술회의논문집; 한국과학기술대학, 충남; 16-17 Oct. 1987
• /
• pp.237-241
• /
• 1987

In this paper, the BTR (Behind the Tape Reader) type communication unit which interfaces the IEBM PC/XT to the FANUC 5M NC controller is developed, making it possible to send NC part program from the memory of IBM PC/XT to the NC controller. As an example of integration of CAD and CAM technologies, the machining of a two dimensional hand-written free line which incorporates the processes of geometric data acquisition using a digitizing tablet, automatic part programming and control of NC milling machine operation is demonstrated.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.1770-1773
• /
• 1991

In this paper we present one modeling system, which is composed of a 3-dimensional proile measurement unit, a CAD system and a NC milling machine. This system is compactly combined so that measurement, designing and manufacturing can be performed efficiently. This system was actually applied to make a plaster model of the pottery.