• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.1
• /
• pp.73-81
• /
• 2008

Intercooling and aftercooling are required in order to operate air compressor, these are conducted through air-cooled or water-cooled heat exchangers. This study aims to find more suitable type of heat exchanger as a water-cooled intercooler of air compressor. Comparative performance evaluation among fin-tube heat exchanger and shell-and-tube (S&T) heat exchanger having various tubes such as circular tube, spiral tube, and internally finned tube was conducted. Thermal-hydraulic performance of each heat exchanger type is evaluated in terms of temperature drop and pressure drop. The comparisons show that shell-and-tube heat exchangers may have similar and larger heat transfer capacity to the fin-tube heat exchanger if tube diameter is reduced and multiple pass is adopted. For these cases, however, compressed air pressure drop in shell-and-tube heat exchanger become much larger than that in fin-tube heat exchanger.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.1
• /
• pp.33-41
• /
• 2011

This study presents modeling technologies applicable to an unbonded post-tension system using a finite element software package. In this study, both direct modeling method and multiple spring method were used. The direct modeling method adopts tube-to-tube contact elements to represent the physical feature of a post-tension system. The multiple spring method uses virtual tendons attached to the real tendons using a number of rigid axial springs that freely rotate at the ends. Both modeling technologies provide accurate predictions. However, only the multiple spring method provides numerically stable and reliable responses with a consideration of concrete tension stiffening effects. Therefore, the multiple spring method turned out to be a generally applicable modeling technology for the unbonded post-tension system. Comparisons were made for the analytical and experimental results for the verification of the selected method, and parameter studies were carried out to confirm the appropriateness of the modeling assumptions and parameters adopted in the analysis.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.335-340
• /
• 2009

Operating medium or large scale industrial boilers in partial load condition, the burner should undergo the off-design points resulting in poor exhaust gas characteristics. To obtain the stable turn down performance, two or more burners can be used for the industrial boiler. In case multiple burners are adopted, the heat transfer can be enhanced by arranging the burners properly. In the present study, numerical simulations have been conducted for the combustion chamber of a 2 t/h class industrial boiler in order to clarify the heat transfer characteristics at the combustion chamber.

• Journal of computational fluids engineering
• /
• v.14 no.2
• /
• pp.77-83
• /
• 2009

Operating medium or large scale industrial boilers in partial load condition, the burner should undergo the off-design points resulting in poor exhaust gas characteristics. To obtain the stable turn down performance, two or more burners can be used for the industrial boiler. In case multiple burners are adopted, the heat transfer can be enhanced by arranging the burners properly. In the present study, numerical simulations have been conducted for the combustion chamber of a 2 t/h class industrial boiler in order to clarify the heat transfer characteristics at the combustion chamber.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.11
• /
• pp.1127-1133
• /
• 2012

A finned-tube-type evaporator module has been proposed for a 2 t/h-class water-tube-type industrial boiler with multiple burners. The geometry of the fins was changed at each module to equalize the evaporation. The modules were designed by considering the energy balance at each row rather than by following a conventional bulk design procedure. The designed module was built into a 2 t/h-class water-tube-type boiler, and its performance was tested. A numerical simulation was also conducted to evaluate the two- or three-dimensional effects of factors such as the inlet conditions. The numerical simulation also included the conjugate heat transfer problem to predict the fin tip temperature. The heat transfer coefficient with fins is lower than that obtained from the empirical correlation of a bare tube. The fin tip temperature from CFD is higher than that from the analytical solution.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.2
• /
• pp.87-94
• /
• 2003

To reduce the air side pressure drop in air-cooled heat exchanger, tow-in type winglet vortex generators are applied. A specially designed multiple-channel test core was used in the experiments for the various geometry of winglet vortex generators. The proposed tow-in type vortex generator gives significant separation delay, reduces form drag, and removes the zone of poor heat transfer from near-wake of the tubes. The results show the significant pressure drop reduction for the tow-in win91e1 vortex generators with the similar enhancement of the heat transfer as other vortex generator applications in heat exchanger. In the range of Reynolds number of 350 to 2100 the pressure drop decrease 8∼15% and 34∼55% for the in-line and staggered tube banks, respectively, compared to those without vortex generators.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.1199-1204
• /
• 2006

The pressure drop and heat transfer coefficient were measured at room temperature in CFB heat exchanger with multiple vertical tubes. Also the circulation rate of solid particles was measured. The theoretical model for predicting heat transfer coefficient using the solid flowrate was developed in this study. The model predictions were compared with the measured heat transfer coefficient to show relatively good agreement.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.6
• /
• pp.317-323
• /
• 2013

A multi-perforated tube indicates the existence of multiple holes of various shapes on the surface of a long cylinder-type or rectangular tube, and a hole installed on the surface is called an orifice, as it is relatively small in size, compared with the surface area of the tube. In this study, the flow characteristics of a circular multi-perforated tube with many orifices on the surface were investigated experimentally and numerically. The volume flowrate issuing from each orifice, discharge angle, effective flow area ratio, and the flow fields around the orifices were measured and visualized, with the variation of the orifice area ratio, at the same blockage ratio. The volume flowrate distributions along the flow direction of the multi-perforated tube tends to be more uniform, as larger orifices were positioned at the inlet side of the multi-perforated tube, compared with no orifice area change along the flow direction.

• The Journal of the Korea Contents Association
• /
• v.21 no.3
• /
• pp.752-760
• /
• 2021

The present study aimed to identify predictors of Youtube creator's Willingness to work as a profession. This work is notable, given its prevalence in preference as an occupation due to the development of information and communication technology. In the present work, a survey study was utilized and respondents' perception of job values, interest, self-esteem as well as willingness to work were measured. The results from a multiple regression analysis indicate that, realistic type (-), artistic type (+), corporate type (+) job value and job interest were significantly predictive of willingness to work. This study discussed implications including the need to establish career support services for YouTube creators as a profession and further for differentiated approaches based on job values or individual tendencies. The result from the current work is important, in that this study identified the willingness and influential factors of YouTube creators from a professional perspective, reflecting the recent growing interest in YouTube creators.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.288-293
• /
• 2005

The pressure distribution and heat transfer coefficient were measured at room temperature in the high suspension density CFB heat exchanger with multiple vertical tubes and the effective density of CFB was determined. The theoretical model for predicting heat transfer coefficient was developed in this study. The model predictions were compared with the measured heat transfer coefficient to show relatively good agreement between them.