• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.938-945
• /
• 1996

The present studies are to describe the grafting reaction of styrene in various solvents to polypropylene fabric by the simultaneous method using Co-60. The influence of various factors such as absorbed dose, dose rate, type of solvent, acid and multifunctional monomer were evaluated. At constant absorbed dose, the grafting yield was found to be higher at low dose rate. The initial rate of grafting was found to be proportional to a 0.56 power of dose rate. The inclusion of mineral acid in the grafting solution led to an increase in radiation grafting yield at almost all monomer concentration examined. Multifunctional monomer was also effective to increase grafting yield. The addition of both acid and multifunctional monomer was found to accelerate the grafting yield much more than the separate addition of two additives.

• Polymer(Korea)
• /
• v.24 no.6
• /
• pp.763-769
• /
• 2000

The multifunctional cation exchangers, sulfonated polypropylene-g-(acrylic acid/styrene) [PP-g-(AAc/Sty)] were synthesized by the irradiational grafting of AAc and Sty onto PP staple fabric with electron beam accelerator and its subsequent sulfonation. The highest degree of grafting obtained was 190% at a monomer mixture of 30 vol% AAc: 70 vol% Sty and a solvent mixture of 30 vol% water : 70 vol% methanol and the degree of grafting decreased with an increase of the AAc content in the monomer mixture at constant solvent content. Maximum ion exchange capacity of the copolymer was 4.6 meq/g. The Li$^{+}$ adsorption ability of the copolymer synthesized in the study was the best among PP-g- AAc, sulfonated PP-g-Sty, and sulfonated PP-g-(AAc/Sty).).

• Bulletin of the Korean Chemical Society
• /
• v.23 no.2
• /
• pp.325-329
• /
• 2002

In this study, the dependency of the behavior of propagating front on the reaction condition in frontal polymerization reaction has been studied. We have used some multifunctional acrylates as a monomer and ammonium persulfate as an initiator for the polymerization reactions. In frontal polymerization, a method of producing polymeric materials via a thermal front that propagates through the unreacted monomer/initiator solution, the behavior of self propagating front shows various dynamic patterns depending on the reaction condition. We have obtained some spin modes of propagating front in the number of 'hot spots' or 'spin heads' by changing the reaction condition. The effect of the reactor tube diameter on the mode of propagating front has also been studied by using some reactor tubes with different size of tube diameter and it has been examined in some detail by adopting an experimental method of two-tubes system.

• Korean Journal of Optics and Photonics
• /
• v.10 no.6
• /
• pp.494-499
• /
• 1999

We report on the results of holographic transmission grating that can be controlled by the applied AC electric field. We have fabricated a polymer-dispersed liquid crystal material that composed of multifunctional acrylate monomer blended with the liquid crystal mixture E7. To investigate an electro-optic properties of fabricated HPDLC, diffraction efficienties (DE) are measured as a fuction of applied electric field and density of liquid crystal. Maximum DE of about 70% is obtained about 30 wt% of LC concentration at a zero field. We have also shown that optical image was recorded in the tllm, and then the reconstructive image was switchable with the applied electric fields. ields.

• Journal of Adhesion and Interface
• /
• v.3 no.1
• /
• pp.9-12
• /
• 2002

In this paper, N,N-m-phenyenedimaleimide (m-PDM), Polyamide Resin (PI) and Metallic dimethacrylate etc. influencing the heat resistance of anaerobic adhesive has been studied, an anaerobic adhesive composition capable of post-cure expansion and $230^{\circ}C$ temperature resistance comprising a multifunctional methacrylate and m-PDM capable of effectuating expansion upon post-cure has been developed. A homogeneous mixture of a monomer and m-PDM are subjected to a first cure heat stage (Room Temperature) wherein a rigid partially-cured plastic is formed and a post-cure heat stage ($150^{\circ}C$) to effectuate permanent expansion of cured adhesive composition.

• Applied Chemistry for Engineering
• /
• v.9 no.4
• /
• pp.516-522
• /
• 1998

In this study, a water adsorbent was synthesized by radiation grafting of acrylic acid and multifunctional monomers such as 1,2-propanediol dimethacrylate (PDMA) and 1,1,1-trimethylolethane triacrylate (TMETA) onto cellulose and its subsequent treatment with 5% NaOH. Its absorbency on $H_2O$ and 0.9 % NaCl aqueous solution was examined. The highest absorbency on water and on 0.9% NaCl aqueous solution was obtained from the addition of 0.75 vol % PDDMA and of 1.0 vol % TMETA onto acrylic acid solution, respectively. The absorbency of commercial hygienic band on water and NaCl aqueous solution was 21 g/g and 22 g/g, respectively. However, that for acrylic acid-grafted cellulose including TMETA was 298 g/g and 54 g/g, respectively.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.442-446
• /
• 2007

Alkali soluble and photo-curable polyesters were prepared from fluorene epoxy acrylate and various aromatic dianhydrides. To make a black matrix for LCD color-filter application, photo-resist solution was made by mixing synthesized polyester as binder, carbon black as pigment, initiator and multifunctional monomer in solvent. Black matrix pattern was formed on the glass substrate by lithography process. In this study, we synthesized various polyester-based binder polymers for LCD color-filter applications, and compared the analytical properties of those polymers and lithography patterns.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1028-1034
• /
• 1999

Poly(lactic acid) is expected to be one of the most promising biodegradable polymers. However, the high molecular weight polymer could be obtained by ring-opening polymerization process conventionally, which raises the production cost and decreases the final yield. In this study, linear and star-shaped poly(L-lactic acid)s were prepared by direct solution polycondensation method and their physical and thermal properties were examined. Tin compounds were found to be effective catalyst for the preparation of high molecular weight polymers. When 0.2g (0.5 wt % of monomer) of $SnCl_2$ and 100 mL of p-xylene were used, the polymer yield and molecular weight were relatively high. As a means to obtain higher molecular weight polymer easily in the direct polycondensation system, dipentaerythritol(dipet) or pentaerythritol(pet) was introduced as a multifunctional branching monomer to provide a star-shaped poly(lactic acid). Moderately high molecular weight polymers with the inherent viscosity values up to 1.14 dL/g(weight-average molecular weight of about 140000 by GPC) were obtained and could be cast strong and transparent films.

• Korean Journal of Optics and Photonics
• /
• v.14 no.2
• /
• pp.109-115
• /
• 2003

We Have fabricated a holographic polymer-dispersed liquid crystal (HPDLC) thin film, which is composed of multifunctional acrylate monomer blended with the nematic liquid crystal mixture, and then investigated the real-time diffraction efficiencies for various amounts of liquid crystals and applied AC electric fields. It is experimentally shown that the holographic gratings recorded in the HPDLC film can be reversibly erased and reconstructed by switching on and off an appropriate applied AC electric field. By use of these electro-optic properties we have developed bifocal holographic lenses having two different focal lengths of 30cm and 40 cm.