• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1537-1540
• /
• 2003

MEMS technology with micro scale is complete system utilized as the sensor. micro electro device. The metallization of MEMS is very important to transfer the power operating the sensor and signal induced from sensor part. But in the MEMS structures local stress concentration and deformation is often happened by geometrical shape and different constraint on the metallization. Therefore. this paper studies the effect of supporting type and thickness ratio about thin film thickness of the substrate thickness for the residual stress variation caused by thermal load in the multi-layer thin film. Specimens were made from materials such as Al, Au and Cu and uniform thermal load was applied, repeatedly. The residual stress was measured by FEA and nano-indentation using AFM. Generally, the specimen made of Al induced the large residual stress and the 1st layer made of Al reduced the residual stress about half percent than 2nd layer. Specimen made of Cu and Au being the lower thermal expansion coefficient induce the minimum residual stress. Similarly the lowest indentation length was measured in the Au_Cu specimen by nano-indentation.

• Journal of Welding and Joining
• /
• v.19 no.1
• /
• pp.49-57
• /
• 2001

In this study, the residual stress fields of multi-pass welded were analyzed by FEA under various geometrical conditions. In order to estimate the effects of pipe geometries on residual stress distribution, welding processes of each model were performed under the same heat cycles. And then, the influence of cutting off the weld bead on the residual stress redistribution was also estimated. From the results, in the range of t/D=0.05, axial residual stresses on the outer surface of the welded pipe were linearly decreased with pipe diameter increase. On the other hand, hoop residual stresses were not influenced by them. And both axial and hoop residual stresses on the outer surface of the welded pipe were increased with pipe diameter increase. But, when t/D was smaller than 0.05, they were converged in the nearly same value. The maximum residual stresses were generated at around HAZ. It in therefore necessary to consider them in welding design, strength evaluation, and analysis of fracture characteristics.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.43 no.1
• /
• pp.42-49
• /
• 2023

The plant-specific NAC transcription factors control various biological processes, including plant development and stress responses. We have isolated an ANAC032 gene, one of the NAC transcription factor family, which was highly activated by multi-abiotic stresses, including high salt and drought in Arabidopsis. Here, we generated transgenic plants constitutively expressing ANAC032 and its knockout to identify the functional roles of ANAC032 in Arabidopsis under abiotic stress responses. The ANAC032-overexpressing plants showed enhanced tolerance to salinity and drought stresses. The anac032 knockout mutants were observed no significant changes under the high salt and drought conditions. We also monitored the expression of high salt and drought stress-responsive genes in the ANAC032 transgenic plants and anac032 mutant. The ANAC032 overexpression upregulated the expression of stress-responsive genes, RD29A and ERD10, under the stresses. Thus, our data identify that transcription factor ANAC032 plays as an enhancer for salinity and drought tolerance through the upregulation of stress-responsive genes and provides useful genetic traits for generating multi-abiotic stress-tolerant forage crops.

• Journal of Families and Better Life
• /
• v.27 no.2
• /
• pp.255-268
• /
• 2009

The purpose of this study was to deepen our understanding about mothers' parenting stress in multi-cultural families. The study was conducted through in-depth interviews of 6 mothers from Mongolia, Philippines, and Japan who were living in Seoul. The findings of this study were as follows. First, mothers of multi-cultural families had difficulties of giving birth and child rearing, especially in the earliest years of their children. They were not fully adapted to the ways of living in Korea with little social support from family members and neighbors. Second, they were worried about their children's development, particularly language development due to their lack of understanding and fluency in Korean. Third, they were concerned about the cultural and racial discrimination against their children. They expected their children to be treated and respected equally like ordinary Korean children. Fourth, they were anxious about the fact that their children might not acquire the basic academic skills before they enter the elementary schools. Furthermore, they were worried that their children might not get as much educational support as they want. Fifth, despite the burden of mother's role in Korea, they wished to get a job to support their children for better education. In conclusion, the marriage immigrant mothers experienced the stress due to the lack of social support, the discrimination against immigrants, the possibilities of their children's delays in development, the disparity in the level of support for educating their children and the high expectations about their children's education in Korean society. Therefore it is necessary for the policy makers to consider more practical support system for the multi-cultural families in order for the marriage immigrant mothers to build up self-confidence in child rearing and educating their children.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.8
• /
• pp.617-626
• /
• 2021

During supersonic flight of vehicles, the thermal behavior of structures under high-temperature environment is important for thermal-structural design. In this study, full-field thermal deformation and stress concentration of the notched structure was performed using global-local multi-digital image correlation (multi-DIC) systems. This techniques were developed and implemented by multi-DIC systems consists of 2D DIC system and 3D DIC system. The specimen was heated in a heating chamber to achieve the thermal expansion behavior. Then the images of structure's deformation and stress concentration at various temperature were recorded and analyzed by multi-DIC system. Afterward, full-field thermal deformation of the notched structure was determined with DIC technique and stress concentration at the notched structure was calculated by further processing. Finite element analysis of the notched structure is performed in ABAQUS^TM and the results of the experiments show good agreement with those obtained from simulation. The results achieved in this study show the efficiency of the muilti-DIC method in thermal deformation as well as stress concentration of notched structure.

• Geotechnical Engineering
• /
• v.11 no.1
• /
• pp.23-40
• /
• 1995

In order to investigate the characteristics of the lateral earth pressure at rest under hysteretic Ko -loading l unloading conditions. Seven types of multicyclic models have been studied experimentally using dry sand. For this study a new type of Ko -oedometer appal attn is developed, and horizontal pressure is accurately measured. The multi cyclic models consist of largely 3 cases : (i) Ko-test under the same loading/unloading condition, (ii) multi-cyclic loading /unloading Ko -test exceeding the maximum prevertical stress, and (iii) multi-cyclic loading l unloading Ko -test within the mazimium prevertical stress. As a result, the multi -cyclic model showed that single-cyclic model could be extended as well, in which the exponents for unloading condition(a and a') and the reloading coefficients(m, and m*) were mainily dependent upon type of stress model, number of cycles and relati ve density.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.4769-4775
• /
• 2014

This paper discusses the dynamics stress of each boom, which occurs as a result of the conflicts on a multi-joint boom at the end effector and structure. In this process, CATIA was applied to create 3D modeling, ADAMS and ANSYS were then performed using mesh analysis by obtaining the stress data to create a MNF(Modal Neutral File) of multi-joint boom. Two types of MNF models were analyzed using ADAMS FFT(Fast Fourier Transform) performing to check the validity of each model. In this process, the models were verified by ADAMS, which performs the dynamic characteristics of conflict. The ADAMS Durability was used to analyze the maximum stress between the multi-joint boom and structure.

• Geomechanics and Engineering
• /
• v.20 no.2
• /
• pp.113-120
• /
• 2020

Rock damage is the main cause of accidents in underground engineering. It is difficult to predict rock damage accurately by using only one parameter. In this study, a rock failure prediction model was established by using stress, energy, and damage. The prediction level was divided into three levels according to the ratio of the damage threshold stress to the peak stress. A classification predicting model was established, including the stress, energy, damage and AE impact rate using Bayesian method. Results show that the model is good practicability and effectiveness in predicting the degree of rock failure. On the basis of this, a multi-parameter classification predicting deterioration model of rock failure was established. The results provide a new idea for classifying and predicting rockburst.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.469-472
• /
• 2004

There have been numerous accelerated aging laboratory tests for evaluating suitability of polymeric materials and devices. Aging test for materials and its full scale device has been conducted, but poor correlation of aging test such as service experience were observed. Service experience plays a key role in the utility section of composite insulators. A meaningful and reliable accelerated aging test is needed for evaluating composite insulator. During the service these insulators are subjected to aging stress such as humidity, pollution, and electrical field, and erosion and tracking of the weathershed occurs. This paper presents the criteria of reliability evaluation and evaluation facilities for 22.9 kV suspension composite insulator. We adopt the criteria of reliability evaluation consist of two test methods. One is CEA tracking wheel test for examining the tracking and erosion performance of composite insulator. The other is multi-stress aging test for examining effects of environmental factors such as UV, temperature, humidity, etc on composite insulator.

• Korean Journal of Child Studies
• /
• v.32 no.1
• /
• pp.31-49
• /
• 2011

This study centred around the development of a parenting training program for improving parent-child relationships in multi-cultural families and to examine the effects of the program. The goal of this program was to improve parent-child relationships in multi-cultural families. The program consists of 8 sessions and each session employs a variety of activities and teaching methods to help multi-cultural mothers to become more involved in the a program. The participants were 12 mothers of multi-cultural backgrounds in Seoul and Asan city. There 12 mothers were assigned to the experimental group participated in this program for a total of 8 sessions. Data were analyzed according to frequencies, percentiles, means, standard deviations, and paired t-test. The results of this study indicated that this parenting training program for improving parent-child relationships was effective in improving multi-cultural mother's parenting efficacy and reducing their parenting stress.