• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.25-30
• /
• 2011

In this study, it is performed numerical simulation on multi-phase flow by means of CIP-CSI2 scheme. It is applied In a two-phase free surface flow problem at a high density ratio equivalent to that of an air-water system, for examining the computational capability. The method that is being developed and improved is a CIP(Constrained Interpolation Profile) and CSL2(Conservative Semi-Lagrangian) based Cartesian Grid Method.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.6
• /
• pp.1071-1079
• /
• 2007

In this paper, a novel space vector control method for isolated multi-level inverter using 3-phase low frequency transformers is proposed. This method is based on the simplification of the space-vector diagram of a five-level inverter using calculated table into fully programming method. The execution time of the proposed method is about same as that of the method using calculated table. Also, the proposed method is easily applied to other case level inverter. We applied this method into the 3-phase IHCML inverter using common arm. It makes possible to use a single DC power source due to employing low frequency transformers. In this inverter, the number of transformers could be reduced compare with an exiting 3-phase multi-level inverter using single phase transformer. In addition, this method generates very low harmonic distortion operation with nearly fundamental switching frequency. Finally, We tested multi-level inverter to clarify electric circuit and reasonableness through Matlab simulation and experiment by using prototype inverter.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.2
• /
• pp.82-90
• /
• 2015

This paper proposes an efficient bi-directional DC/DC converter topology using multi-phase interleaved method for power storage system. The proposed converter topology is used for a power storage system using a vanadium redox flow battery(VRFB) and is configured to enable bidirectional power flow for charging and discharging of VRFB. Proposed DC/DC converter of the 4 leg method is reduced to 1/4 times the rating of the reactor and the power semiconductor device so can be reduce the system size. Also, proposed topology is obtained the effect of four times the switching frequency as compared to the conventional converter in each leg with a 90 degree phase shift 4 leg method. This can suppress the reduction of the life of the secondary battery because it is possible to reduce the current ripple in accordance with the charging and discharging of VRFB and may increase the efficiency of the entire system. In this paper, it proposed bidirectional high-efficiency DC/DC converter topology Using multi-phase interleaved method and proved the validity through simulations and experiments.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.4
• /
• pp.576-585
• /
• 2016

The current control methods of Y-connected 7 Phase BLDC motor are sine wave current control and square wave control. The sine wave current control method needs dq axis transformation of $7{\times}7$ matrix for current control and very complex. Also this method is not suitable for multi Phase BLDC motor of trapezoidal back emf wave. Therefore, in Y connected multi phase BLDC motor, the square wave current control methods are required. Generally, in the 3Phase BLDC system, Average current control method is used for current control. The average current is obtained that the summation of absolute value of each phase current magnitude is divided by the number of conduction phase. However, if average current control method is applied to multi-phase system, there is a problem that each phase currents are different. This problem affects unbalance of each phase torque and fluctuation of total torque. This paper proposed each phase current control method of Y connected 7Phase BLDC system. Proposed method is used for PI controller of each phase for each phase current control. This method can perfect square wave current control. Also, configuration of the method is easier than DQ axis transformation. Proposed method is verified through simulation and experiments.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.7
• /
• pp.352-360
• /
• 2003

This paper deals with a simple method in order to analyze and compare the harmonic characteristics in the multi-level inverter. Generally, the magnitude of harmonic components becomes different according to the multi-carrier Pulse Width Modulation(PWM) techniques, the modulation index($M_i$) and the switching frequency The previous papers analyzed the harmonic characteristics from the viewpoint of the space voltage vector. Hence, the calculation of the harmonic vector becomes more difficult and complex in 4-level or over 5-level. However, the proposed method has reduced an amount of calculation and simplified the process of it, using the relationship between the reference voltage and the output phase voltage to the load neutral point. It is applied to the 5-level cascade inverter and the harmonic characteristics for each multi-carrier PWM technique are compared through the simulation.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.2
• /
• pp.221-228
• /
• 1989

The objective of this paper is to develop a numerical technique for analyzing crack driving forces in multi-phase materials. The analysis was based on finite element method coupled with a virtual crack extension technique which is known as the most efficient tool in computational fracture mechanics analysis. The modified J-integral method, proposed by Miyamoto and Kikuchi for the analysis of dual-phase material was carried out by subtracting the J-values for contours surrounding each phase boundary from the J-values for overall contour. It was shown that the proposed numerical procedure, based on the modified J-integral coupled with a virtual crack extension technique, can be used as an effective numerical tool for determining crack driving forces in multi-phase materials.

• New Physics: Sae Mulli
• /
• v.68 no.12
• /
• pp.1378-1383
• /
• 2018

Multi-wavelength holography has a better axial range than single-wavelength holography, thus allowing unambiguous phase imaging. Noise amplification is the limiting factor in multi-wavelength holography as noise is amplified by a factor equivalent to the magnification of the wavelengths. Here, we propose a new algorithm to remove noise amplification in multi-wavelength holography. The proposed method does not use phase unwrapping and removes $2{\pi}$ ambiguities. Experiments and numerical simulations indicated that the proposed method is fast, has low noise, and is useful for measuring samples with arbitrary step heights.

• Journal of Mechanical Science and Technology
• /
• v.20 no.6
• /
• pp.840-848
• /
• 2006

We carried out numerical studies to investigate the single- and two-phase flow characteristics in the single- and multi-channels. We used the finite volume method to solve the mass and momentum conservation equations. The volume of fluid model is used to predict the two-phase flow in the channel. We obtained the distribution of velocity fields, pressure drop and air volume fraction for different water mass flow rates. We also calculated the distribution of mass flow rates in the multi-channels to understand how the flow is distributed in the channels. The calculated results for the single- and two-phase flow are partly compared with the present experimental data both qualitatively and quantitatively, showing relatively good agreement between them. The numerical scheme used in this study predicts well the characteristics of single-and two-phase flow in a multi-channel.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.11
• /
• pp.155-160
• /
• 2001

To achieve high precision cutting as well as production capability in the machine tool, it is needed to develop excellent rigidity statically, dynamically and thermally as well. In order to predict the qualitative behavior of a machine tool, simultaneous analysis of mechanics and heat transfer is required. Generally, machine tool designers have solved designing problems based on partial estimation of the specified rigidity. This study clears the inter-relationship between therm, and propose multi-phase optimization of machine tool structure using a genetic algorithm. The multi-phase solution method is consists of a series of mechanical design problem. At this first phase of static design problem, multi-objective optimization for the purpose of minimization of the total weight and static compliance minimization is solved using the Pareto Genetic Algorithm.

• Current Optics and Photonics
• /
• v.2 no.4
• /
• pp.332-339
• /
• 2018

A new multi-frequency fringe projection method is proposed to reduce the nonlinear phase error in 3-D shape measurements using an adaptive compensation method. The phase error of the traditional fringe projection technique originates from various sources such as lens distortion, the nonlinear imaging system and a nonsinusoidal fringe pattern that can be very difficult to model. Inherent possibility of phase error appearing hinders one from accurate 3-D reconstruction. In this work, an adaptive compensation algorithm is introduced to reduce adaptively the phase error resulting from the fringe projection profilometry. Three different frequencies are used for generating the gratings of projector and conveyed to the four-step phase-shifting procedure to measure the objects of very discontinuous surfaces. The 3-D shape results show that this proposed technique succeeds in reconstructing the 3-D shape of any type of objects.