• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.75-76
• /
• 2010

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.1
• /
• pp.73-79
• /
• 2011

Inkjet printhead may have a lot of nozzles to increase productivity as a manufacturing tool. So, the uniformity of jetting performance among a lot of nozzles has been one of the key issues in inkjet technology In this study, we investigated the cross-talk effect which should be reduced for uniform jetting performance among a lot of nozzles. Due to the cross-talk, the jetting performance of a nozzle can be affected when neighboring nozzles are firing. For experimental study, we used commercial inkjet head SE-128 from Dimatix. To understand the cross-talk effect of SE-128 head, we measured the change in jetting speed of a nozzle when neighboring nozzles are jetting. The measured jetting speed was compared to the case of one nozzle jetting. Also, we used laser vibrometer to measure change in pressure wave due to cross-talk. As a result of the cross-talk, the jetting speed can become faster or sometimes slower depending on firing nozzle location. If the all nozzle are jetting, the jetting speed of a nozzle became slower because the pressure wave for jetting is reduced.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.975-976
• /
• 2008

• Journal of computational fluids engineering
• /
• v.21 no.2
• /
• pp.112-119
• /
• 2016

NEXTSat-1 is the next-generation small-size artificial satellite system planed by the Satellite Technology Research Center(SatTReC) in Korea Advanced Institute of Science and Technology(KAIST). For the control of attitude and transition of the orbit, the system has adopted a RHM(Resisto-jet Head Module), which has a very simple geometry with a reasonable efficiency. An axisymmetric model is devised with two coil-resistance heaters using xenon(Xe) gas, and the minimum required specific impulse is 60 seconds under the thrust more than 30 milli-Newton. To design the module, seven basic parameters should be decided: the nozzle shape, the power distribution of heater, the pressure drop of filter, the diameter of nozzle throat, the slant length and the angle of nozzle, and the size of reservoir, etc. After quasi one-dimensional analysis, a theoretical value of specific impulse is calculated, and the optima of parameters are found out from the baseline with a series of multi-physical numerical simulations based on the compressible Navier-Stokes equations for gas and the heat conduction energy equation for solid. A commercial code, COMSOL Multiphysics is used for the computation with a FEM (finite element method) based numerical scheme. The final values of design parameters indicate 5.8% better performance than those of baseline design after the verification with all the tuned parameters. The present method should be effective to reduce the time cost of trial and error in the development of RHM, the thruster of NEXTSat-1.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.7
• /
• pp.27-32
• /
• 2008

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.2
• /
• pp.50-53
• /
• 2008

A design approach using a one-dimensional (1D) lumped model was studied and applied to an industrial inkjet printing head design for micro patterning on printed circuit boards. For an accurate analysis, a three-dimensional piezoelectric-driven actuator model was analyzed and its jetting characteristics were applied to 1Danalysis model. The performance of the 1D lumped model was verified by comparing measured and simulated results. The developed 1D model helped to optimize the design and configuration of the inkjet head and could be implemented in the design of multi-nozzle inkjet printing heads to improve the jetting frequency and minimize crosstalk.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1400-1403
• /
• 2007

The 3DP(three dimensional printing) technology is one of the SFF(solid freeform fabrication) technologies which has recently come into a spotlight due to its suitability to various field. A manufacturing process of product is using many pattern formation technology. The 3DP technology uses multi nozzle that can fabricate three dimensional object of high speed and accuracy. In this paper, we introduce a development of the office type solid freeform fabrication system. This system is used UV resin and multi-piezo head.

• IE interfaces
• /
• v.10 no.1
• /
• pp.155-167
• /
• 1997

The purpose of this study is to develop the program for efficient operation of a multi-functional surface mounting device(SMD) which mount various components on a printed circuit board(PCB). These components are provided by diverse types of feeders such as cassette, stick and tray feeders. The SMD has one or two heads. In the SMD, the positions of PCB and feeders and fixed, and the head moves to pick up a component from a feeder and to mount it on the PCB. The number of lanes occupied by each feeder and the nozzle used for each component can be different. We develop an off-line program to minimize the cycle-time of the SMD by studying the optimal assignment of feeders and the optimal mounting sequence of components. Graphical User Interface(GUI) is also developed. Additionally, we consider the line balancing problem which appears when two SMDs are used sequentially.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.9
• /
• pp.781-786
• /
• 2015

Recently, studies of 3D printing methods have been working in various applications. For example, the powder base method laminates the prints by using a binding or laser sintering method. However, the draw back of this method is that the post process is time consuming and does not allow for parts to be rapidly manufactured. The binding method requires the post process while the time required for the post process is longer than the manufacturing time. This paper proposes a UV curing binding method with an integrated piezo printing head system. The optimization of an arbitrary waveform generation for the control of a UV curable resin droplet was researched, in addition to developed optimized UV curing processes in multi nozzle ink jet heads.