• Korean Journal of Materials Research
• /
• v.19 no.5
• /
• pp.259-264
• /
• 2009

In this study we investigated the effect of the multi-step texturing process on the electrical and optical properties of hydrogenated Al-doped zinc oxide (HAZO) thin films deposited by rf magnetron sputtering. AZO films on glass were prepared by changing the $H_2/(Ar+H_2)$ ratio at a low temperature of $150^{\circ}C$. The prepared HAZO films showed lower resistivity and higher carrier concentration and mobility than those of non-hydrogenated AZO films. After deposition, the surface of the HAZO films was multi-step textured in diluted HCl (0.5%) for the investigation of the change in the optical properties and the surface morphology due to etching. As a result, the HAZO film fabricated under the type III condition showed excellent optical properties with a haze value of 52.3%.

• Journal of Powder Materials
• /
• v.20 no.4
• /
• pp.297-301
• /
• 2013

Mirror surface machining for large area flattening in the display field has a problem such as a tool wear and a increase in machining time due to large area machining. It should be studied to decrease machining time and tool wear. In this paper, multi-tool machining method using a PCD tool and a SCD tool was applied in order to decrease machining time and tool wear. Machining characteristics (cutting force, machined surface and surface roughness) of PCD tool and SCD tool were evaluated in order to apply PCD tool to flattening machining. Based on basic experiments, the PCD/SCD multi-tool method and the SCD single-tool method were compared through surface roughness and machining time for appllying large area mold machining.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.43-44
• /
• 2015

Electrodeposited Ni and Ni-SiC composite coatings were prepared on Cu substrates by using the Ni-Sulfamate electrolytic bath. Thus prepared samples were subjected for the two different types of post surface modification techniques; i.e. Laser Surface Texturing (LST) and Ultrasonic Nano Surface Modification (UNSM), respectively in order to investigate their effects on surface and interface related properties of the coatings. Hemispherical dimples, with 80 to 200 um dimple spacing, were created and examined on the surfaces of the materials studied. The results revealed that micro-surface texturing with 150 um dimple spacing considerably improved the coefficient of friction. Dimple spacing accuracy and incorporated second phase ceramic particles both contributed significantly to reduction in coefficient of friction. On the other hand, application of UNSM considerably modified the surface topography, led to increase the Vickers microhardness, and reduced the wear and coefficient of friction as compared to non UNSM treated Ni and Ni-SiC samples.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.287-295
• /
• 2019

Privacy films are typically manufactured by combining black resin and transparent louver-shaped patterns. The use of black resin results in excellent light-shielding. However, black resin can reduce the transmittance of privacy films at the front viewing angle. In this study, we applied $SiO_2/SiON$ multi-layer thin films on a privacy film to maintain transmittance at the front viewing angle and improve light-shielding at the side viewing angle. We determined the optimum combination of thicknesses of the $SiO_2/SiON$ multi-layer stacks to increase the overall transmittance; the light shielding could be maximized at the side viewing angle.

• Proceedings of the Korean Fiber Society Conference
• /
• 2007.11a
• /
• pp.445-446
• /
• 2007

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2007.11a
• /
• pp.153.1-153.1
• /
• 2007

• Korean Journal of Agricultural Science
• /
• v.38 no.3
• /
• pp.533-540
• /
• 2011

This study is to develop a mulit-layer glued columns for construction of Korean-style houses by using domestic small diameter logs. Dried small square lumber glued each other to develop a multi-layer glued columns and evaluated its performance of strength. Then, predicted the design load of multi-layer glued columns and make a comparison between actual load and design load of multi-layer glued columns. In the results, allowable load by allowable stress of multi-layer glued columns was measured one-third of actual columns load and prediction load was measured less than 10~30% of the actual load. Therefore, muilt-layer glued member has a standard allowable stress of compressive of 13 MPa (Larix leptolepis) and 19 MPa (Chamaecyparis obtusa) when used as columns. Also, using compression strength of small diameter square logs could calculate maximum loads of multi-layer glued member as column.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.10
• /
• pp.93-98
• /
• 2019

Recently, with the development of the aerospace and automotive industries, the demand for high-melting-point materials has increased. However, high-melting-point materials are difficult to cut through conventional machining methods. Thermally assisted machining (TAM) is a method for improving the machinability by preheating the materials. A laser, the most commonly used device for TAM, has high efficiency through local preheating but is not sufficient for maintaining a high preheating temperature due to rapid cooling. However, the use of multi-heat sources can supplement the disadvantage of a single heat source. The high preheating temperature can be maintained with a wide and deep heat-affected zone (HAZ) by multi-heat sources. The purpose of this study is to analyze the preheating effects of multi-heat sources using laser plasma. Thermal analysis and preheating experiments were carried out. As a result, the high preheating effect of multi-heat sources compared with a single heat source was verified.

• Applied Microscopy
• /
• v.52
• /
• pp.14.1-14.10
• /
• 2022

An electron probe X-ray microanalyzer (EPMA) is an essential tool for studying chemical composition distribution in the microstructure. Quantifying chemical composition using standard specimens is commonly used to determine the composition of individual phases. However, the local difference in chemical composition in the standard specimens brings the deviation of the quantified composition from the actual one. This study introduces how to overcome the error of quantification in EPMA in the practical aspect. The obtained results are applied to evaluate the chemical com position of retained austenite in multi-phase steel. Film-type austenite shows higher carbon content than blocky-type one. The measured carbon contents of the retained austenite show good coherency with the calculated value from the X-ray diffraction.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.3
• /
• pp.262-269
• /
• 2006

Formaldehyde and total volatile organic compounds (TVOC) from building materials have been known as main causes of IAQ problem in Newly-Constructed Multi-Family Houses. Because Multi-Family Houses are built in large quantities in a similar manner, inappropriate selection of building materials and method will detrimental affect IAQ. This research aims to identify major causes of Indoor Air Pollutants in Multi-Family Houses, by constructing Mock-Up & One-Room House. As a result, self leveling concrete, door, and furniture construction is a major cause of indoor formaldehyde increase, and tile bond is TVOC, and urethane water proof is Etylbenzene, and Xylene.