• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.6
• /
• pp.282-288
• /
• 2017

In this paper, GaAs/AlGaAs multi-layer structure was grown by liquid phase epitaxy with graphite sliding boat, which can be used as a device structure of a photocathode image sensor. The multi-layer structure was grown on an n-type GaAs substrate in the sequence as follows: GaAs buffer layer, Zn-doped p-type AlGaAs layer as etching stop layer, Zn-doped p-type GaAs layer, and Zn-doped p-type AlGaAs layer. The Characteristics of GaAs/AlGaAs structures were analyzed by using scanning electron microscope (SEM), secondary ion mass spectrometer (SIMS) and hall measurement. The SEM images shows that the p-AlGaAs/p-GaAs/p-AlGaAs multi-layer structure was grown with a mirror-like surface on a whole ($1.25mm{\times}25mm$) substrate. The Al composition in the AlGaAs layer was approximately 80 %. Also, it was confirmed that the free carrier concentration in the p-GaAs layer can be adjusted to the range of $8{\times}10^{18}/cm^2$ by hall measurement. In the result, it is expected that the p-AlGaAs/p-GaAs/p-AlGaAs multi-layer structure grown by the LPE can be used as a device structure of a photoelectric cathode image sensor.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.2
• /
• pp.172-177
• /
• 2004

In this paper, DGS(Defected Ground Structure) is applied to multi-layer structure using LTCC(Low Temperature Co-fired Ceramics). Sprial DGS is adopted in order for size-reduction and higher quality factor, the multi-layer DGS has the same characteristics as the planar DGS. Multi-layer bandpass filter of new shape is confiured using two multi-layer spiral DGS and is designed with no via-hole for the simple process. 5.25 GHz Wireless LAN bandpass filter is designed and fabricated, the insertion loss of the filter is measured less than 1.5 dB, and the size is 2.0 mm${\times}$1.2 mm${\times}$1.1 mm(L${\times}$W${\times}$H).

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.777-778
• /
• 2006

This paper deals with the optimum rotor design approach about the multi-layer design of the buried magnets in an Interior Permanent Magnet Synchronous Motor (IPMSM), on the efficiency improvement by using Response Surface Methodology (RSM). In the multi-layer design of the prototype 15kw IPMSM, the constant amount of buried PM is split from the single-layer into double-layer design for improving the efficiency characteristics. The optimum double-layer rotor structure is built with the help of RSM analysis. The improvement of IPMSM efficiency is verified by the Finite Element Method (FEM) results comparison with the prototype single-layer IPMSM.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.2 s.31
• /
• pp.43-47
• /
• 2004

A coupler or divider is a microwave passive component used for power coupling or dividing. Regarding the trend of current telecommunication systems monolithic integration of passive components is highly desirable. In this study by the LTCC(Low temperature co-fired ceramics) technology a 2012 size type dual band coupler with multi-layer structure was fabricated. To achieve the desired coupling values for both DCS and EGSM bands, broad side coupled patterns were used with multi-layer structure. Its characteristics such as coupling, insertion loss, isolation and directivity values were measured and compared with simulation results.

• Journal of Korea Multimedia Society
• /
• v.15 no.9
• /
• pp.1093-1101
• /
• 2012

Multi-view video is obtained by capturing one three-dimensional scene with many cameras at different positions. Multi-view video coding exploits inter-view correlations among pictures of neighboring views and temporal correlations among pictures of the same view. Multi-view video coding which uses many cameras requires a method to reduce the computational complexity. In this paper, we proposed an efficient prediction structure to improve performance of multi-view video coding. The proposed prediction structure exploits an average distance between the current picture and its reference pictures. The proposed prediction structure divides every GOP into several small groups to decide the maximum index of hierarchical B layer and the number of pictures of each B layer. Experimental results show that the proposed prediction structure shows good performance in image quality and bit-rates. When compared to the performance of hierarchical B pictures of Fraunhofer-HHI, the proposed prediction structure achieved 0.07~0.13 (dB) of PSNR gain and was down by 6.5(Kbps) in bitrate.

• Journal of Power System Engineering
• /
• v.2 no.2
• /
• pp.41-46
• /
• 1998

This paper presents the vibration control for the two degree-of-freedom which is a reduced model of multi-layer structure. This reduced model is designed for the first and second order resonance in the low frequency domain where the disturbance such as the earth quake has the large energy. And a designed controller using the LQ type $H_{\infty}$ control theory shows the good performance for the impulse disturbance through the experimental results and the simulation results respectively.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.11a
• /
• pp.163-164
• /
• 2014

This study is conducted for prevent spread of penetration water and water leakage through non-woven fabric between PVC sheet and PVC sheet in the PVC composite waterproofing sheet of a multi-layer structure. For this, carry out absorption amount test to confirm spread resistance performance after manufacturing PVC composite waterproofing sheet of a multi-layer structure using water-repellency processed non-woven fabric. As a result of test, weight of water-repellency processed non-woven fabric increased to 1.178g, Compared with beginning and there are not penetration water.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.4
• /
• pp.391-397
• /
• 2001

The guided wave propagation in inhomogeneous multi-layered structures is experimentally explored based on theoretical dispersion curves. It turns out that proper selection of incident angel and frequency is critical for guided wave generation in multi-layered structures. Theoretical dispersion curves greatly depend on adhesive zone thickness, layer thickness and material properties. It was possible to determine the adhesive zone thickness of an inhomogeneous multi-layered structure by monitoring experimentally the change of dispersion curves.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.979-982
• /
• 1999

A new accurate as well as efficient multi-layer interconnect capacitance extraction method is presented. Since Multi-layer interconnects is too complicated to directly extract capacitances, it is simplified with virtual ground concept. To make the structure tractable, the shielding effects should be separately determined. Since the electric field shielding effects, and the solid-ground-based capacitance matrices can be readily determined from the layout geometry, the accurate as well as efficient quasi-3D capacitances concerned with an objective line can be readily determined. In order to demonstrate its efficiency and accuracy, the parameters and circuit responses were benchmarked with 3D-field-solver-based results.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.618-618
• /
• 2013

Graphene is only one atom thick planar sheet of sp2-bonded carbon atoms arranged in a honeycomb crystal lattice, which has flexible and transparent characteristics with extremely high mobility. These noteworthy properties of graphene have given various applicable opportunities as electrode and/or channel for various flexible devices via suitable physical and chemical modifications. In this work, for the development of all-graphene devices, we performed to synthesize alternately patterned structure of mono- and multi-layer graphene by using the patterned Ni film on Cu foil, having much different carbon solid solubilities. Depending on the process temperature, Ni film thickness, introducing occasion of methane and gas ratio of CH4/H2, the thickness and width of the multi-layer graphene were considerably changed, while the formation of monolayer graphene on just Cu foil was not seriously influenced. Based on the alternately patterned structure of mono- and multi-layer graphene as a channel and electrode, respectively, the flexible TFT (thin film transistor) on SiO2/Si substrate was fabricated by simple transfer and O2 plasma etching process, and the I-V characteristics were measured. As comparing the change of resistance for bending radius and the stability for a various number of repeated bending, we could confirm that multi-layer graphene electrode is better than Au/Ti electrode for flexible applications.