• 한국항공우주학회지
• /
• 제34권8호
• /
• pp.8-15
• /
• 2006

고받음각의 NACA23012익형에 대하여 synthetic jet을 이용하여 박리 제어를 수행하였다. 단일 synthetic jet을 이용하여 익형에 발생하는 앞전 박리를 효과적으로 지연시킬 수 있고, 또한 실속 특성을 개선 할 수 있음을 확인하였다. 그때 발생하는 비정상 유동 특성을 파악하였다. 또한, 현실적으로 구현 가능한 jet 속도를 얻기 위하여 multi-array synthetic jet의 특성을 파악하였다. 그리고, 단일 위치에 장착된 synthetic jet을 이용하여 박리를 제어 하였을 경우 익형 윗면에 발생하는 작은 와동을 제거하기 위하여, multi-location synthetic jet을 이용하였다. 작은 와동을 제거하고 안정적인 유동을 확보하기 위하여, 높은 진동수의 synthetic jet을 이용하여 국부적으로 효과적인 박리 제어를 통한 익형 주변의 유동의 전체적 특성을 안정화 시킬 수 있음을 확인하였다. Multi-location synthetic jet의 phase 변화를 이용하여 multi-array/multi-location synthetic jet의 성능 및 특성을 향상 시킬 수 있음을 확인하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 추계 학술대회논문집
• /
• pp.60-66
• /
• 2007

Separation control has been performed using synthetic jets on airfoil at high angle of attack. Computed results demonstrated that stall characteristics and control surface performance could be substantially improved by resizing separation vortices. It was observed that the actual flow control mechanism and flow structure is fundamentally different depending on the range of synthetic jet frequency. For low frequency range, small vortices due to synthetic jet penetrated to the large leading edge separation vortex, and as a result, the size of the leading edge vortex was remarkably reduced. For high frequency range, however, small vortex did not grow up enough to penetrate into the leading edge separation vortex. Instead, synthetic jet firmly attached the local flow and influenced the circulation of the virtual airfoil shape which is the combined shape of the main airfoil with the separation vortex. Theses results show the characteristic of unsteady flow of single synthetic jet. Beside, we researched on multi-array synthetic jet to obtain applicable synthetic jet velocity. Multi-location synthetic jet is proposed to eliminate small vortex on suction surface of airfoil. With the results, we concluded that the flow around airfoil is stable by high frequency synthetic jet with elimination of small vortex and confirmation of stable flow. Moreover, performance of multi-array/multi-location synthetic jet can be improved by changing phase angle of multi-location synthetic jet.

• 대한기계학회논문집B
• /
• 제28권2호
• /
• pp.135-145
• /
• 2004

An experimental study is conducted to investigate the flow and heat transfer characteristics of a multi-tube inserted impinging jet. Four different multi-tube devices are tested for various nozzle-to-plate distance. Flow visualization by smoke-wire method and velocity measurements using a hot-wire anemometer are applied to analyze the flow characteristics of the multi-tube insert impinging jet. The local heat transfer coefficients of the multi-tube inserted impinging jet on the impingement surface are measured and the results are compared to those of the conventional jet. In multi-tube inserted system the multi-tube length plays an important role in the flow and heat transfer characteristics of the jet flow. With multi-tube insert of I3d4 and I6d4 which has relatively longer tube length than the multi-tube-exit of I3d1 and I6d1, the flow maintains its increased velocity far downstream due to interaction between adjacent flows. For the small H/D of 4, the local heat transfer coefficients of multi-tube inserted impinging jet are much higher than those of the conventional jet because the flow has higher velocity and turbulent intensity by the use of the multi-tube device. At large gap distance of H/D=12, also higher heat transfer rates are obtained by installing multi-tube insert except multi-tube insert of I3d1.

• 동력기계공학회지
• /
• 제3권1호
• /
• pp.23-28
• /
• 1999

Experimental and theoretical researches about jet pump have been carried out by many researchers. Jet pump can be used for the transportation of solid materials, farm produce, and fishes. It is the purpose of this paper to seek optimal multi nozzle shape of the annular jet pump. Experiments were done for several jet nozzle areas, jet nozzle arrays and jet nozzle lengths. Water was used for both the primary fluid and secondary fluid. The efficiency curves for the annular jet pump having multi nozzles are presented in this paper.

• Journal of Biosystems Engineering
• /
• 제20권1호
• /
• pp.66-72
• /
• 1995

A numerical study for a two dimensional multi-impingement jet with crossflow of the spent fluid has been carried out. To study the flow characteristics especially in the jet flow region, three different distributions of mass flow rate at 5-jet exits were assumed. For each distribution, various Reynolds numbers ranging from laminar to turbulent flows were considered. Calculations drew the following items as conclusion. 1) A periodical fully developed flow was observed from the third protrusion. This was also observed from previous experimentally by Whidden at al. The Nessult number at the protrusion surface increased mildly as going downstream. 2) The low Reynolds number turbulence model of Launder and Sharma was found to be adequate for the prediction of fluid flow and heat transfer characteristics of two dimensional multi-jet configuration. 3) The Nusselt number at the protrusion surface was nearly proportional to the square root of the Reynolds number.

• Journal of Biosystems Engineering
• /
• 제20권1호
• /
• pp.58-65
• /
• 1995

A numerical study for a two dimensional multi-jet with crossflow of the spent fluid has been carried out. Three different distributions of mass-flow rate at 5 jet exits were assumed to see their effects upon the flow characteristics, especially in the jet-flow region. For each distribution, various Reynolds numbers ranging from laminar to turbulent flows were considered. Calculations drew the following items as conclusion. 1) The development of the free jets issued from downstream jets was hindered by the crossflow formed due to jets. Consequently, the free jet was developed into the channel flow without any evident symptom of impingement jet flow characteristics 2) The crossflow induced the pressure gradient along the cross section of jet exits and the value of the pressure gradient increased as going downstream. The crossflow generated also the turbulent kinetic energy as it collied with the downstream jets. 3) The skin friction coefficient along the impingement plate was affected more by the distribution of mass flow rate at jet exits rather than by the Reynolds number. The skin friction coefficient was inversely proportional to the square root of the Reynolds number, regardless of flow regime when a fully developed flow was formed in the jet flow region. 4) The distribution of the skin friction coefficient along the impingement plate was found to be controlled by adjusting the distribution of mass flow rate at jet exits.

• 동력기계공학회지
• /
• 제4권1호
• /
• pp.33-38
• /
• 2000

The characteristics of center-driver jet pump which have multi-nozzle were studied in this research. Jet nozzles are connected outside of the bend rather than inserted in the bend in order to transport solid materials or fish without any harm. Jet pumps having one nozzle, two nozzles, four nozzles, and sixteen nozzles were tested in this study. The efficiencies and performances of jet pumps were studied for several nozzles shape, for three different mixing chamber shapes, for two suction area shapes. All the efficiency curves for these cases are presented in this paper.

• 한국항공우주학회지
• /
• 제48권3호
• /
• pp.187-194
• /
• 2020

본 연구에서는 고도에 따른 간섭 유동과 공력특성을 파악하고, 측추력 제트에 사용된 기체의 종류에 따라 다화학종 가스제트의 확산을 고려한 유동해석을 수행하였다. 공기제트에 비해서 임의로 가정한 다화학종 가스 제트를 사용하는 경우 충격파의 위치와 제트의 확산 영역이 동체전방으로 이동한다. 이로 인해 표면의 고압영역이 앞으로 나가며 같은 조건에서 보다 높은 피칭 모멘트를 갖는다. 또한 고온효과의 적용에 따라 압력분포 예측에 차이를 보였다. 그리고 저고도의 측추력제트 유동 구조와 비교했을 때 중고도 유동조건에서 주변 대기의 낮은 밀도로 측추력 제트의 두께가 더 크며, 넓은 영역에 걸쳐 확산된다.

• 한국환경과학회지
• /
• 제11권10호
• /
• pp.1039-1044
• /
• 2002

In this study, breakwater model which has several outlet pipes to discharge water is settled in the experimental open channel and mean velocity distributions of multi wall jet are measured. The length of zone of flow establishment of wall jet is shorter than that of free jet and decay rate of jet centerline longitudinal velocity along x is linear in $0.3{leq}x/I_p{leq}17$. The rate of vertical width and lateral width spreading of multi wall jet is respectively 0.0753, 0.157.

• 대한치과기공학회지
• /
• 제37권3호
• /
• pp.169-178
• /
• 2015

Purpose: This study was to investigate usage satisfaction of multi type handpiece with equipped air-jet function Methods: The subjects of this study through the survey was conducted for fifty-nine dental technicians in Daegu and Gyeongsangbukdo from the May 7 to 19, after the June 23 to July 4 2014. The survey was about the function and quality through user testing environment by cutting zirconia specimens using appliance for zirconia. The collected date was analyzed by the statistical program SPSS Win Ver 19.0 for the satisfaction of handpiece and control system. To test for significance on each item, p<0.05 had been decided a standard. General characteristics and relationship between the handpiece and control system was performed correlation analysis. Results: The results of this study is as follows. 35 dental technicians had 1~2 years career in zirconia part as the highest 59.3%, 95% of subjects expected that the prospects for the zirconia material have bright prospects. The satisfaction of multi type handpiece and control system design and function showed a significant difference. Subjects satisfied with the design and function of the multi type showed negative correlation with those of Standard. The satisfaction of multi type handpiece showed 3.37 points of air jet, 3.05 points of noise level, 2.69 points of water flow rate, and 1.98 points of cruise function. Sample differences in all parameters showed a statistically higher difference. Conclusion: High-speed cutting mechanism of multi-type is recommended working with zirconia materials and the multi-type unit combined handpiece motor, air-turbine and air-gun will be expected the increase of user due to the high satisfaction of air jet.