• 한국정밀공학회지
• /
• 제14권6호
• /
• pp.22-27
• /
• 1997

In general, the load which acts on the structure is almost independent of time in many locations. In this case. It is difficult to estimate the life with the service load history, because the structure is on the multi- axial and multi-point loading states. In this study, the service load of the excavator which is widely used in industry field was calculated using measured cylinder pressures and displacements. The fatigue life was estimated using the multi-axial and multi-point load counting method. Service load history of 4 pin joint which act independently each other is yielded by mult-axial and multi-point load counting method. The stress spectrum is yielded by superposition of the results of FEM stress analysis applied unit load. Palm- gren-Miner's cumulative Damage is 0.000804 for Von Mises equivalent stress sequence by one side fillet weld S-N curve. This result agress with Bench test results. As a result of this study, the fatigue life esti- mation using the multi-axial and multi-axial and multi-point load counting method is useful.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.913-920
• /
• 1996

In this study, the counting method for multi-axial and multi-point load states was proposed. Using this counting method, the load spectrum is generated from the service load history which is measured for boom structure of excavator. Loading state for loading points of boom structure is described as a multi-dimensional state space. From this load spectrum, the stress spectrum was generated by FEM analysis using the superposition of the unit load. The cumulated damage at the severe damage point of In nm structure by the failure example is calculated by Palmgren-Miner's rule. As a result of this study, the fatigue life estimation using the multi-axial and multi-point load counting method is useful.

• Structural Engineering and Mechanics
• /
• 제1권1호
• /
• pp.17-30
• /
• 1993

A practical multi-spring model is proposed for a nonlinear analysis of reinforced concrete members, especially columns, taking into account the interaction of axial load and bi-directional bending moment. The parameters of the model are determined on the basis of material properties and section geometry. The axial force-moment interaction curve of reinforced concrete sections predicted by the model was shown to agree well with those obtained by the flexural analysis utilizing realistic stress-strain relations of materials. The reliability of the model was also examined with respect to the test of reinforced concrete columns subjected to varying axial load and bi-directional lateral load reversals. The analytical results agreed well with the experiment.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 가을 학술발표회 논문집
• /
• pp.501-508
• /
• 2001

Free vibration analysis of multi-delaminated composite beam-columns subjected to axial compression load is performed in the present study. In order to investigate the effects of multi-delaminations on the natural frequency and elastic buckling load of multi-delaminated beam-columns, the general kinematic continuity conditions are derived from the assumption of constant slope and curvature at the multi-delamination tip. Characteristic equation of multi-delaminated beam-column is obtained by dividing the global multi-delaminated beam-columns into segments and by imposing recurrence relation from the continuity conditions on each sub-beam-column. The natural frequency and elastic buckling load of multi-delaminated beam-columns according to the incremental load of axial compression, which is limited to the maximum elastic buckling load of sound laminated beam-column, are obtained. It is found that the sizes, locations and numbers of multi-delaminations have significant effect on natural frequency and elastic buckling load, especially the latter ones.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.666-671
• /
• 1993

Fatigue life prediction under multi-axial variable load were performed for Aluminium 7075-T651 alloy using SAE Notched specimen & Torque tube shaft component specimen. When variable multiaxial load is applied to material, maximum damaged plane(critical plane) change. To clarify the situation, experiment is performed on two different changing load path. For multiaxial fatigue life prediction, miner rule is expanded to critical plane theory. Shear based parameter and Elliptical parameter give better correlation. This suggests that miner rule can be applicable on multi-axial variable load.

• 한국소음진동공학회논문집
• /
• 제21권10호
• /
• pp.875-882
• /
• 2011

In this paper, the finite element analysis model of the mult-axial wheel durability test configuration is created using SAMCEF. Mooney-Rivlin 2nd model is applied to the tire model, and the variation of the air pressure inside the tire is considered. Vertical load, lateral load and camber angle are applied to the simulation model. The tire rotates because of the friction contact with a drum, and reaches its maximum speed of 60 km/h. The dynamics stress results of the simulation and experiment are compared, and the reliability of the simulation model is verified.

• 한국압력기기공학회 논문집
• /
• 제19권2호
• /
• pp.140-145
• /
• 2023

When performing stress analysis for a nozzle in nuclear power plants, the nozzle loads should be determined conservatively. Existing stress analysis report of 3-D nozzle loads in nuclear power plants often provide only load magnitude not the sign (direction). Since calculated stress distribution depends on load direction, determining critical load directions for conservative stress analysis is crucial. In this study, an efficient method for determining critical load directions in nozzle loads is proposed. In the proposed method, stresses are firstly calculated using elastic finite element (FE) analysis for the uni-axial load in each direction. Then stress distributions for the multi-axial loads are analytically calculated using the principle of superposition. The calculated stress values are verified by comparing with FE analysis results under multi-axial loading. By using this method, the complex task of determining conservative load directions can be simplified.

• 한국전산구조공학회논문집
• /
• 제15권3호
• /
• pp.523-534
• /
• 2002

본 논문에서는 축방향 압축하중을 받는 다퐁간분리된 적층 보-기둥의 자유진동과 좌팔에 대한 해석을 수행하였다. 다층간분리된 적층 보-기둥의 고유진동수와 탄성 좌굴 하중에 대한 층간분리의 영향을 조사하기 위해 층간분리의 양단에서 기울기와 곡률이 일정하다는 가정을 적용하여 일반적인 운동학적 연속 조건을 유도하였다. 전체 다층간분리된 보-기둥을 부분으로 분할하고, 연속조건에 따른 반복관계를 각 하부 보-기둥에 부과함으로써 다층간분리된 보-기둥의 특성방정식을 구하였다. 축방향 증분 압축 하중에 따른 다층간분리된 보-기둥의 고유진동수와 탄성 좌굴 하중을 구하였으며 이는 손상되지 않은 적층 보-기둥의 최대 탄성 좌굴 하중에 한정된다 연구를 통하여 층간분리의 크기, 위치, 수가 고유진동수와 특히 탄성 좌굴 하중에 큰 영향을 미치는 것을 알 수 있었다.

• 국제강구조저널
• /
• 제18권5호
• /
• pp.1525-1540
• /
• 2018

A test rig with multi-functional purposes was specifically designed and manufactured to study the behavior of multi-planar welded tubular joints subjected to multi-planar concurrent axial loading. An experimental investigation was conducted on full-scale welded tubular joints with each consisting of one chord and eight braces under monotonic loading conditions. Two pairs or four representative specimens (two specimens for each joint type) were tested, in which each pair was reinforced with two kinds of different internal stiffeners at the intersections between the chords using welded rectangular hollow steel sections (RHSSs) and the braces using rolled circular hollow steel sections (CHSSs) and welded RHSSs. The effects of different internal stiffeners at the chord-brace intersection on the load capacity of joints under concurrent multi-planar axial compression/tension are discussed. The test results of joint strengths, failure modes, and load-stress curves are presented. Finite element analyses were performed to verify the experimental results. The study results show that the two different joint types with the internal stiffeners at the chord-brace intersection under axial compression/tension significantly increase the corresponding ultimate strength to far exceed the usual design strength. The load carrying capacity of welded tubular joints decreases with a higher degree of the manufacturing imperfection in individual braces at the tubular joints. Furthermore, the interaction effect of the concurrent axial loading applied at the welded tubular joint on member stress is apparent.

• 한국안전학회지
• /
• 제31권4호
• /
• pp.97-103
• /
• 2016

This study investigates effects of partially earth anchored cable system on the structural safety for a long-span cable-stayed bridge under dynamic loads such as seismic and wind load. For a three span cable-stayed bridge with a main span length of 810 m, two models are analyzed and compared; one is a bridge model with a self anchored cable system, the other is a bridge model with a partially earth anchored cable system. By performing multi-mode spectrum analysis for a prescribed seismic load and multi-mode buffeting analysis for a fluctuating wind component, the structural response of two models are compared. From results, the partially earth anchored cable system reduce the maximum pylon moment by 66% since earth anchored cables affect the natural frequencies of girder vertical modes and pylon longitudinal modes. In addition, the girder axial forces are decreased, specially the decrement of the axial force is large in seismic load, while girder moment is slightly increased. Thus, the partially earth anchored cable system is effective system not only on reduction of girder axial forces but also improvement of structural safety of a cable-stayed bridge under dynamic loads such as seismic and wind loads.