• Journal of Electrical Engineering and Technology
• /
• 제13권4호
• /
• pp.1586-1595
• /
• 2018

For the problem that the complexity of 3-D modeling and multi parameter optimization, as well as the uncertainty of the winding factor of axial flux permanent magnet generator with coreless windings. The complex 3-D model was simplified into 2-D analytic model, and an analytical formula for the winding factor that adapting different coreless stator winding is proposed in this paper. The analytical solution for air-gap magnetic fields, no-load back EMF, electromagnetic torque, and efficiency are calculated by using this method. The multiple objective and multivariable optimization of the maximum fundamental and the minimum harmonic content of back EMF are performed by using response surface methodology. The proposed optimum design method was applied to make a generator. The generator was tested and the calculated results are compared with the proposed method, which show good agreements.

• International Journal of Fluid Machinery and Systems
• /
• 제9권4호
• /
• pp.338-353
• /
• 2016

Information on the surge behaviors and stall stagnation boundaries for a nine-stage axial flow compressor are summarized on the basis of analytical data in comparison with those for a single-stage one, with attention to the pressure ratio effect. The general trends of the surge loop behaviors of the pressure-mass flow are similar for both compressors including the fact that the subharmonic surges tend to appear very near the stall stagnation boundaries. With respect to the nine-stage compressor, however, the mild loops in the subharmonic surges tend to be very small in size relative to the deep loops, and at the same time, insufficient surge recovery phenomenon, which is a kind of subharmonic surge, appears also far from the stagnation boundary for relatively short delivery flow-paths. The latter is found to be a rear-stage surge caused by unstalling and re-stalling of the rear stages with the front-stages kept in stall in the stalled condition of the whole compressor, which situation is caused by stage-wise mismatching in the bottom pressure levels of the in-stall multi-stage compressor. The fundamental information on the stall stagnation boundaries is given by a group of normalized geometrical parameters including relative delivery flow-path length, relative suction flow-path length, and sectional area-pressure ratio, and by another group of normalized frequency parameters including relative surge frequencies, modified reduced resonance frequencies, and modified reduced surge frequencies. Respective groups of the normalized parameters show very similar tendency of behaviors for the nine-stage compressor and the single-stage compressor. The modified reduced resonance frequency could be the more reasonable parameter suggesting the flow-induced oscillation nature of the surge phenomena. It could give the stall stagnation boundary in a more unified manner than the Greitzer's B parameter.

• 한국입자에어로졸학회지
• /
• 제17권3호
• /
• pp.71-79
• /
• 2021

Ultrafine dust, which is emitted from industrial factories or all kinds of vehicles, threatens the human's respiratory system and our environment. In this regard, separating airborne particles is essential to mitigate the severe problem. In this work, an axial cyclone for the effective technology of eliminating harmful dust is investigated by numerical simulation using Ansys 2020, Fluent R2. In addition, the optimized structure of the cyclone is constructed by means of multi objective optimization based on the response surface method which is a representative method to analyze the effect of design parameter on response variables. Among several design parameters, the modified length of the vortex finder and dust collector is a main point in promoting the performance of the axial cyclone. As a result, the optimized cyclone exhibits remarkable performance when compared to the original model, resulting in pressure drop of 307 Pa and separator efficiency of 98.5%.

• Composites Research
• /
• 제28권3호
• /
• pp.136-141
• /
• 2015

The stitching process has been widely utilized for the improvement of through-thickness property of the conventional laminated composites. This paper reports the effects of stitching on the flexural and interlaminar shear properties of multi-axial warp knitted (MWK) composites in order to identify the mechanical property improvements. In order to minimize the geometric uncertainties associated with the stacking pattern of fabrics, the regular lay-up was considered in the examination of the stitching effect. The key parameters are as follows: the stitch spacings, the stitching types, the stitching location, and the location of compression fixture nose. These parameters have little effect on the flexural and interlaminar shear properties, except for the case of stitching location. However, the geometry variations caused by the stitching resulted in minor changes to the mechanical properties consistently. Stitching on the $0^{\circ}$ fibers showed the lowest flexural strength and modulus (12% reduction for both properties). The stitch spacing of 5 mm resulted in 8% reduction for the case of interlaminar strength compared with that of 10 mm spacing.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권2호
• /
• pp.193-200
• /
• 2008

탄-소성론에 근거한 콘크리트나 토질과 같은 재료의 파괴 포락선은 주응력을 축으로 하는 공간 좌표계상에서 인장의 등압(hydrostatic stress)축을 향해 기울어진 형태를 가지며 소성흐름이 상관소성흐름 법칙(associated flow rule)에 따라 결정될 경우 콘크리트의 거동 예측시에 과도한 체적 팽창률을 나타내게 된다. 본 논문에서는 콘크리트의 다축응력 하에서의 거동을 예측하기 위하여 비균일 경화(nonuniform hardening)를 적용한 5계수 파괴 포락선과 등압축 방향 성분의 소성 흐름을 수정하는 비상관 소성흐름 법칙(non-associated flow rule)을 사용하여 비선형 유한요소해석 프로그램을 개발하였으며 신뢰성 있는 연구자의 다축응력 실험결과와 유한요소해석 프로그램의 해석결과를 비교하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 추계 학술발표회
• /
• pp.574-584
• /
• 2006

Bi-directional loading test data are available to evaluate the design parameters which reflect the characteristics of a construction method and the variations of ground at the site where drilled shafts are installed. The method to obtain the design parameters of a real bridge by hi-directional loading test was introduced. The plans of multi-level testing and installation of measuring instruments should be made according to the rough estimation of axial bearing capacity, the length of pile, and the construction method. While the relationship between end bearing resistance and displacement was obtained directly from the hi-directional loading test, the relationship between unit side resistance and displacement was calculated through the measuring values. 1% displacement of pile diameter was adopted as the criteria of failure for ultimate resistance. As the settlement of pile head at the total ultimate bearing capacity obtained from these method was less than 1.5 % of pile diameter, this method was conservative to use in the field.

• Wind and Structures
• /
• 제21권2호
• /
• pp.119-158
• /
• 2015

The characteristics of the coherence functions of X axial, Y axial, and RZ axial (i.e., body axis) wind forces on the Shanghai World Trade Centre - a 492 m super-tall building with section varying along height are studied via a synchronous multi-pressure measurement of the rigid model in wind tunnel simulating of the turbulent, and the corresponding mathematical expressions are proposed there from. The investigations show that the mathematical expressions of coherence functions in across-wind and torsional-wind directions can be constructed by superimposition of a modified exponential decay function and a peak function caused by turbulent flow and vortex shedding respectively, while that in along-wind direction need only be constructed by the former, similar to that of wind speed. Moreover, an inductive analysis method is proposed to summarize the fitted parameters of the wind force coherence functions of every two measurement levels of altitudes. The comparisons of the first three order generalized force spectra show that the proposed mathematical expressions accord with the experimental results well. Later, the influences of coherence functions on wind-induced dynamic responses are analyzed in detail based on the proposed mathematical expressions and the frequency-domain method of random vibration theory.

• 융복합기술연구소 논문집
• /
• 제7권2호
• /
• pp.1-5
• /
• 2017

The rotating electrodynamic wheel over a conductive plate produces thrust force as well as normal force. Specially, separating the conductive plate and spacing apart each part, the lateral stability of the rotating wheel is guaranteed due to the restoring force into neutral position. In this paper, the force characteristics of the electrodynamic wheel rotating over the conductive plate is analyzed using the finite element tool. First, the dominant parameters are identified considering the geometric configuration and the operating condition. And the sensitivity for the parameter deviation is quantified for the high force density. The above topology can be applied as an actuating principle for inter-city train as well as contact-free transfer device.

• 한국콘텐츠학회논문지
• /
• 제11권12호
• /
• pp.814-821
• /
• 2011

256 다중 검출기 전산화단층촬영 (multi detector computed tomography, MDCT)에서 두개부 전용 팬톰을 이용하여 분해능 파라메터와 재구성 필터의 영상 품질을 평가하고자 하였다. 사용한 장비는 256 MDCT 을 사용하였으며 philips system head phantom을 이용하여 Extended Brilliance Workspace에서 영상의 질 평가를 측정하였다. 장비에서 지원하고 있는 분해능 파라메터와 재구성 필터가 화질에 미치는 영향을 알아보기 위해서 검사조건을 $512{\times}512$ matrix, $128{\times}0.625$ mm beam collimation, 120 kVp, 250 mAs, 0.5 sec, 250 mm field of view (FOV), 절편 두께와 절편 간격은 5 mm, 1.0 pitch로 동일하게 적용하였다. 분해능 파라메터은 'Standard', 'High', 'Ultrahigh'로 구분하여 적용하였으며, 재구성 필터는 'A', 'B', 'C', 'D', 'UA', 'UB', 'UC' 등으로 바꿔가면서 영상을 재구성하여 노이즈, 균일도, 직선성, 변조전달함수 (modulation transfer function, MTF)의 50%와 10%를 측정하였다. 그 결과 'High' 분해능은 균일도, 직선성, MTF 50%와 10%에서 우수하였다. 'UA', 'UB' 재구성 필터는 균일도와 노이즈 평가에서 양호했으며 'C'재구성 필터는 직선성과 MTF 50%와 10%에서 양호하였다.

• Earthquakes and Structures
• /
• 제11권5호
• /
• pp.823-840
• /
• 2016

The plastic hinge lengths of beams and columns are a critical demand parameter in the nonlinear analysis of structures using the finite element method. The numerical model of a plastic hinge plays an important role in evaluating the response and damage of a structure to earthquakes or other loads causing the formation of plastic hinges. Previous research demonstrates that the plastic hinge length of reinforced concrete (RC) columns is closely related to section size, reinforcement ratio, reinforcement strength, concrete strength, axial compression ratio, and so on. However, because of the limitations of testing facilities, there is a lack of experimental data on columns with large section sizes and high axial compression ratios. In this work, we conducted a series of quasi-static tests for columns with large section sizes (up to 700 mm) and high axial compression ratios (up to 0.6) to explore the propagation of plastic hinge length during the whole loading process. The experimental results show that besides these parameters mentioned in previous work, the plastic hinge of RC columns is also affected by loading amplitude and size effect. Therefore, an approach toward considering the effect of these two parameters is discussed in this work.