• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.1
• /
• pp.89-94
• /
• 2014

The high Young's modulus and tensile strength of carbon nanotubes has attracted great attention from the research community given the potential for developing super-strong, super-stiff composites with carbon nanotube reinforcements. Over the decades, the strength and stiffness of carbon nanotube-reinforced polymer nanocomposites have been researched extensively. However, unfortunately, such strong composite materials have not been developed yet. It has been reported that the efficiency of load transfer in such systems is critically dependent on the quality of adhesion between the nanotubes and the polymer chains. In addition, the waviness and orientation of the nanotubes embedded in a matrix reduce the reinforcement effectiveness. In this study, we carried out performed micromechanics-based numerical modeling and analysis by varying the geometry of carbon nanotubes including their aspect ratio, orientation, and waviness. The results of this analysis allow for a better understanding of the load transfer capabilities of carbon nanotube-reinforced polymer composites.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.256-256
• /
• 2011

Using plasmas, hydrophobic surfaces are made on various substances such as polyimide films, filter paper, cotton clothes and multi-walled carbon nanotube (MWCNT) with hexamethyldisiloxane (HMDSO), trimethylchlorosilane (TMCS) and toluene reagents. Plasmas are easily and rapidly to change surface of hydrophilic materials into hydrophobic. We have also optimized processing time and maximized contact angle for super-hydrophobicity of MWCNT. Contact angles have been calculated by measuring between substance and probe liquid, and total surface free energies are determined by the Owens-Wendt equation. Figure 1 shows the measured contact angles with time and ratio of reagents on MWCNT.

• Journal of Drive and Control
• /
• v.13 no.1
• /
• pp.43-48
• /
• 2016

This paper presents a preliminary study on the pressure sensing characteristics of smart nano composites made of MWCNT (multi-walled carbon nanotube) to develop a novel pressure sensor. We fabricated the composite pressure sensor by using a solution casting process. Made of carbon smart nano composites, the sensor works by means of piezoresistivity under pressure. We built a signal processing system similar to a conventional strain gage system. The sensor voltage outputs during the experiment for the pressure sensor and the resistance changes of the MWCNT as well as the epoxy based on the smart nano composite under static pressure were fairly stable and showed quite consistent responses under lab level tests. We confirmed that the response time characteristics of MWCNT nano composites with epoxy were faster than the MWCNT/EPDM sensor under static loads.

• Polymer(Korea)
• /
• v.34 no.2
• /
• pp.150-153
• /
• 2010

In this research, biomolecule-immobilized multi-walled carbon nanotubes (MWCNTs) were prepared by using radiation-induced graft polymerization. For the immobilization of biomolecules, the surface of MWNCTs was functionalized by radiation-induced graft polymerization of acrylic acid. Based on the results of TGA and Raman spectroscopy it was found that acrylic acid was effectively graft-polymerized on the MWCNTs. Biomolecules such as DNA and proteins were immobilized onto the resultant poly(acrylic acid)-grafted MWCNTs. The results of the X-ray photoelectron spectroscopy and fluorescence microscopy confirmed that the biomoelcules were successfully immobilized on the poly(acrylic acid)-grafted MWCNTs.

• Journal of the Korea Institute of Building Construction
• /
• v.24 no.2
• /
• pp.203-213
• /
• 2024

This study delves into the mechanical properties of fiber-reinforced cement composites(FRCC) concerning the dispersion method of multi-walled carbon nanotubes(MWCNTs). MWCNTs find utility in industrial applications, particularly in magnetic sensing and crack detection, owing to their diverse properties including heat resistance and chemical stability. However, current research endeavors are increasingly directed towards leveraging the electrical properties of MWCNTs for self-sensing and smart sensor development. Notably, achieving uniform dispersion of MWCNTs poses a challenge due to variations in researchers' skills and equipment, with excessive dispersion potentially leading to deterioration in mechanical performance. To address these challenges, this study employs ultrasonic dispersion for a defined duration along with PCE surfactant, known for its efficacy in dispersion. Test specimens of FRCC are prepared and subjected to strength, drawing, and direct tensile tests to evaluate their mechanical properties. Additionally, the influence of MWCNT dispersion efficiency on the enhancement of FRCC mechanical performance is scrutinized across different dispersion methods.

• Composites Research
• /
• v.24 no.6
• /
• pp.25-30
• /
• 2011

This paper presents an experimental study on the enhancement of electromagnetic shielding (EMI) properties of glass fiber, carbon fiber, and glass-carbon fiber composites by adding layers of multi-walled carbon nanotubes (MWCNTs). In the case of glass-fiber composites, spraying 0.1~0.2 g of MWCNT over a fiber area of $200mm{\times}200mm$ (1.8~3.6 ${\mu}m$ in thickness) resulted in significant improvement in EMI shielding effectiveness (SE). Also, when applying multiple MWCNT layers, it was more effective to place the layers concentrated near the center of the composite rather than spreading them out. On the contrary, inherently conductive carbon fiber and glass-carbon fiber composites did not show appreciable improvement with the addition of MWCNT layers. In order to maximize the effectiveness of carbon nanomaterials as EMI shielding fillers, it is imperative to understand the effect of these materials on various EMI shielding mechanisms and their interactions.

• Carbon letters
• /
• v.13 no.3
• /
• pp.187-189
• /
• 2012

This study investigates the flexural properties of multi-walled carbon nanotube (MWCNT) reinforced basalt/epoxy composites under conditions with and without moisture absorption. The basalt/CNT/epoxy composites were fabricated using 1 wt% silanized MWCNTs and kept in seawater for over 4 months. The flexural properties of the moisture absorbed specimens were evaluated and compared with those of dry specimens. The flexural properties of basalt/CNT/epoxy composites were found to decrease with moisture absorption. The flexural strength and modulus of moisture absorbed specimens were 22% and 16% lower, respectively, than those of the dry specimen. Scanning electron microscope examination of the fracture surfaces revealed that the decreases of flexural properties in the moisture absorbed specimen were due to the weakening of interfacial bonding from swelling of the epoxy matrix.

• Journal of the Korean Vacuum Society
• /
• v.21 no.1
• /
• pp.41-47
• /
• 2012

Multi-walled carbon nanotubes (MWCNTs) incorporated polyacrylonitrile (PAN) and poly (methyl methacrylate) (PMMA) nanofibers were synthesized using electronspinning method. Effects of polymer concentration and applied voltage on the synthesis of PAN and PMMA nanofibers were systematically investigated. The structural characterization of PAN/MWCNTs and PMMA/MWCNTs composited nanofibers synthesized as a function of the MWCNTs concentration was performed by scanning electron microscopy and transmission electron microscopy. 5 wt% MWCNTs incorporated PAN and PMMA electrospun nanofiber exhibit best strength and stiffness.

• Analytical Science and Technology
• /
• v.23 no.2
• /
• pp.165-171
• /
• 2010

Glucose oxidase ($GOD_{ox}$) immobilized biosensor was fabricated by two methods. In one of the methods, gold nanoparticles (Au-NPs) prepared by ${\gamma}$-irradiation were loaded into the poly(maleic anhydride)-grafted multi-walled carbon nanotube, PMAn-g-MWCNT electrode via physical entrapment. In the other method, the Au-NPs were prepared by electrochemical reduction of Au ions on the surface of PMAn-g-MWCNT electrode and then GODox was immobilized into the Au-NPs. The $GOD_{ox}$ immobilized biosensors were tested for electrocatalytic activities to sense glucose. The sensing range of the biosensor based on the Au-NPs physically modified PMAn-g-MWCNT electrode was from $30\;{\mu}M$ to $100\;{\mu}M$ for the glucose concentration, and the detection limit was $15\;{\mu}M$. Interferences of ascorbic acid and uric acid were below 7.6%. The physically Au deposited PMAn-g-MWCNT paste electrodes appear to be good sensor in detecting glucose.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05b
• /
• pp.836-839
• /
• 2011

염료감응형 태양전지의 상대전극으로 MWCNT(multi-walled carbon nanotube)의 농도 (0.01~0.06g)를 달리하여 FTO(fluorine-doped tin oxide) glass에 분산시켜 상대전극을 만들었다. 그리고 glass/FTO/$TiO_2$/Dye(N719)/electrolyte(C6DMII,GSCN)/MWCNT/FTO/glass 구조를 가진 0.45$cm^2$급 DSSC(dye-sensitized solar cells) 소자를 만들었다. 소자의 미세구조, 분산정도, 광특성은 각각 광학현미경, SEM, source measure unit (Keithley model 2400) 장비를 이용하여 확인하였다. MWCNT 농도 증가와 FTO의 거친 표면형상에 따라 비선형적으로 MWCNT 분산면적이 증가하였고, MWCNT 농도 0.06g일 때 FTO 표면에 전체적으로 MWCNT가 완전히 분산됨을 확인하였다. 소자의 광변환 효율은 MWCNT 분산면적에 비례하는 효율을 보였고, MWCNT 분산농도인 0.06g 일 때 4.49%의 광변환 효율을 얻을 수 있었다.