Magazine of the Korean Society of Agricultural Engineers
/
v.17
no.1
/
pp.3677-3684
/
1975
A newly devised dryer with heated air for the farm products, especially suited for high water content materials such as red pepper, Beer ground, each Vegetables, and Low water content materials such as Rough rice was tested for its thermal efficiency and drying mechanism, and the optimum conditions for each sample were established. In order to improve the present rural situation of drying farm products which entirely dependent upon natural solar radiation, a study upon an economic multi-parpose dryer was conducted. A series of drying tests were run first with red pepper which is one of the important cash crop in Korean farm. And successive series of tests were also run with such proaucts as garlic, sweet potatoes, green onion, radish, Beer ground and Rough rice. The results from the above experiment in drying system with heat dryer can be summarized as follows. 1. Drying duration could be shortened by the tempering effect in high water content crop such as red pepper and beer ground. 2. The color changes occured in around 20% water content in red pepper. The degree of color change was heavily affected by high temperature and short drying duration. 3. The drying condition of red pepper was most favourable at the temperature of 85$^{\circ}C$ in early stage and 80$^{\circ}C$ in middle stage and 75$^{\circ}C$ at the final stage, and with the air rate of 0.81㎥/sec and with sample amount of 200kg. 4. The drying condition of Rough rice(I.R.667) was most favourable at the templature of 40$^{\circ}C$ in early stage and 35$^{\circ}C$ in middle stage and final stage and with the air rate of 0.2㎥/sec and with sample amount of 75kg. 5. In order to prevent the color change of red pepper and to assure high efficiency in drying mechanism, it was necessary to lower the temperature as the time passes in drying process. 6. For vege tables, the drying rate were short in early stage and there was also tempering effect. However, for garlics, Constant drying rates through the early and final stages were observed and there were no tempering effects. 7. The drying condition or capability were as follows; Sample drying temp($^{\circ}C$) amount of material(kg) drying time(hr) Red pepper 85 200 9 Garlic 85 150 7 Sweet potato 85 200 6 Green Onion 85 200 4 Carrot 85 200 4 Radish 90 250 4 Rough rice(I.R.667) 35 75 4 Beer ground 90 320 3 Considering the above result of experiments, if this kind of dryers were distributed Korean farm and the optimun process were practiced in rural area, it would certainly help them improving the qualites of their product preventing their undue losses, and thus assuring an increase of Korean farm income and promotion of their living standards.
Journal of Korean Society of Environmental Engineers
/
v.36
no.2
/
pp.147-152
/
2014
In this research, polysulfone hollow fiber membrane was used to recover $CO_2$ which is one of greenhouse gases from flue gas stream being emitted after the combustion of fossil fuels. The prerequisite requirement is to design the membrane process producing high-purity $CO_2$ from flue gas. For separation of $CO_2$, a membrane module and flue gas containing 10% carbon dioxide was used. The effects of operating conditions such as pressure, temperature, feed gas composition and multi-stage membrane on separation performance were examined at various stage cuts. Higher operating pressure and temperature increased carbon dioxide concentration and recovery ratio in permeate. Recovery ratio and separation efficiency increased if a higher content of $CO_2$ injection gas composition. Three-stage membrane system was producing a 95% $CO_2$ with 90% recovery from flue gas. The separation efficiency of three-stage membrane system was higher than one-stage system.
Journal of the Korea Academia-Industrial cooperation Society
/
v.13
no.9
/
pp.3841-3848
/
2012
The process of an analysis of alternatives(AoA) attempts to select the best and balanced solution among a set of multiple candidate solutions under the constraints of cost, schedule, performance and risk(CSPR). The traditional AoA for the acquisition of a new weapon system has usually centered on the sequence of the requirement analysis, design synthesis, and cost estimation. An improved process for AoA is developed in this paper based on a multi-objective decision-making method, which is intended to be applied in the design concept refinement and material solution analysis stage for the acquisition of naval surface ships. The presentation of the proposed AoA approach is then followed by a case study for the next generation multi-purpose training ship based on the principles of systems engineering and also using the models of the effectiveness measure, cost estimation, and risk assessments.
Kim, Jeong-Hoon;Choi, Seung-Hak;Kim, Beom-Sik;Lee, Soo-Bok;Lee, Yong-Taek
Membrane Journal
/
v.17
no.3
/
pp.197-209
/
2007
In this study, a multi-staged pilot-scale membrane plant was constructed and operated for the separation of $CO_2$ from LNG-fired boiler flue gas of 1,000 $Nm^3/day$. The target purity and recovery ratio of $CO_2$ required for the pilot plant were 99% and 90%, respectively. For this purpose, we previously developed the asymmetric polyethersulfone hollow fibers and evaluated the effects of operating pressure and feed concentration of $CO_2$ on separation performance[1,2]. The permeation data obtained were also analyzed in relation with the numerical simulation data using counter-current flow model[3,4]. Based on these results, we designed and prepared the demonstration plant consisting of dehumidification process and four-staged membrane process. The operation results using this plant were compared with the numerical simulation results on multi-staged membrane process. The experimental results matched well with the numerical simulation data. The concentration and the recovery ratio of $CO_2$ in the final stage permeate stream were ranged from $95{\sim}99%$ and $70{\sim}95%$, respectively, depending on the operating conditions. This study demonstrated the applicability of the membrane-based pilot plant for $CO_2$ recovery from flue gas.
Ji, Sae-Hyun;Park, Moon-Seo;Lee, Hyun-Soo;Yoon, You-Sang
Korean Journal of Construction Engineering and Management
/
v.9
no.2
/
pp.170-181
/
2008
Cost of construction project have to be estimated based on drawing before execution. Cost estimate and check would be performed numerously for preparing general outline of requirements and determining the budget at conceptual planning stage, for obtaining decision on every matter related to design, specification, construction and cost at design stage, and for predicting bidding cost. Thus, importance of cost estimation cannot emphasize too much in construction. However, there are lack of standard estimation method, process, and cost analysis method, that square foot estimation method is as used as eyer, in Korea. Thus, This research present the direction for improving cost estimation and management in construction; It is demanded that establishing standard data base methodology, multi-level database model CUBE, and standard cost planning process, choosing cost estimation methodology according to objectives and cost planning process, and making more experts.
Asia-Pacific Journal of Business Venturing and Entrepreneurship
/
v.14
no.6
/
pp.59-76
/
2019
Most technology-based entrepreneurship(TBE) go through an process of decline or disappear without overcoming the valley of death(VoD). The purpose of this study is to identify the growth dimension of TBE and to test the influence of firms activities on firms growth over time. This study identified the two-dimensional growth dimension divided by size and profit through exploratory factor analysis(EFA) of a number of growth indicators. Then, we defined the discrete state of growth firm in four states, divided by size and profit, and five states, including the closure of business. Multi-nomial logit model is used to predict the effect of TBE activities on a discrete state of growth firm(size×profit, closure of business) based on multiple independent variables. The independent variables are based on five representative firms activities: employment, marketing, R&D, financial activities, and general management activities. The growth stage of TBE over time has been categorized into three stages: early stage, middle stage, and late stage of business, taking into account the main periods during which the survival rate of startups sharply decreases. The analytical data of this study was based on the secondary data of the start-up supporting companies of government and public institutions. The subjects of analysis were TBE within 10 years. As a result of the empirical analysis, the employment and marketing activities of TBE show that early and mid-term activities had an effect on the state of firms growth. However, if there is a difference, employment activities have both positive and negative effects, while marketing activities have only a positive effect on size and profit growth. And besides, R&D activities, financial activities, and general management activities throughout the entire process of firms growth were found to be firms activities that have both positive and negative effects on firms growth. In addition, the age of the founder, the firms' industry, and the geographic location of the firms, which are general characteristics of the company, were found to have a distinctive effect on the growth status of the firms according to the growth stage.
Journal of Advanced Marine Engineering and Technology
/
v.41
no.3
/
pp.182-190
/
2017
All liquids contain a small amount of gaseous components and the amount of gases dissolved in a liquid is in accordance with Henry's Law. In a multi-stage thermal-type seawater desalination plant, as the supplied seawater undergoes variations in temperature and pressure in each evaporator, the gases dissolved in the seawater are discharged from the liquid. The discharged gases are carbon dioxide, nitrogen, oxygen, and argon, and these emitted gases are non-condensable. From the viewpoint of convective heat transfer, the evaluation of non-condensable gas released during a vacuum evaporation process is a very important design factor because the non-condensable gases degrade the performance of the cooler. Furthermore, in a thermal-type seawater desalination plant, most evaporators operate under vacuum, which maintained through vacuum system such as a steam ejector or a vacuum pump. Therefore, for the proper design of a vacuum system, estimating the non-condensable gases released from seawater is highly crucial. In the study, non-condensable gases released in a thermal-type seawater desalination plant were calculated quantitatively. The calculation results showed that the NCG releasing rate decreased as the stage comes getting a downstream and it was proportional to the freshwater production rate.
Proceedings of the Korean Society for Technology of Plasticity Conference
/
2008.10a
/
pp.337-340
/
2008
The cross section shape of intermediate die is one of important parameters to obtain dimensional accuracy of final product in shaped drawing process. Until now it has been designed by the experience or trial and error of the expert. In this study, the cross section shape of intermediate die fur spline shape is determined by the electronic field analysis, shape factor method. The result of the electronic field analysis, shape factor method has been compared with that of the present method. The effects of cross section shape on the dimensional accuracy were investigated by using FE analysis. And then the multi-stage shaped drawing experiments were performed to verify the results of FE analysis. As a result, the cross section shape from the electronic field analysis had the good dimensional accuracy. The electronic field analysis can be used for the method to obtain the cross section shape of intermediate die in shaped drawing process.
The healing properties of medicinal maggots (larval stage of Lucilia sericata) are widely used in the chirurgical debridement of non-healing wounds including diabetic foot ulcers, venous and pressure ulcers, where classical approaches have failed. Several kinds of wounds are prone to complications coming out of a specific wound bed environment. There are multi-resistant bacterial species present, their pathogenic impact is multiplied by their ability to form a biofilm. Moreover, immunological events in chronic wounds differ from those in acute wounds. Non-healing wounds are cycled in the early inflammation phase with increased levels of inflammation attributes like inflammation cytokines and matrix metalloproteinases produced by inflammation phase cells. Application of larval therapy promotes progress in the healing process to the next stages involving tissue granulation and re-epithelisation. Larval debridement is an effective method of cleaning the wound of cell debris, necrotic tissue and bacterial load. This happens in a mechanical and biological manner, but the whole complex mechanism of the maggot healing activity is still not fully elucidated. Centuries of clinical practice brings noticeable proof of the maggots' beneficial effect in wound healing management. This long history led to the investigation of the bioactive components of the larval body and its extracts in vitro. We introduce a review which describes the immunomodulation impact of maggot body components on the cellular and molecular levels of the wound healing process.
Proceedings of the Korean Society for Technology of Plasticity Conference
/
2004.05a
/
pp.118-121
/
2004
Manufacturing process for milli components has recently gained researcher's focus with the increasing tendency toward highly integrated and micro-scaled parts for electronic devices. The milli-components cannot be formed by the conventional manufacturing process since the parts require higher dimensional accuracy than the conventional ones. In order to enhance the forming accuracy and productivity, various forming procedures proposed and studied by many researchers. In this paper, forming analysis of milli-components has been studied with a new micro-former. In modeling of progressive dies, multi-stage forming sequence has been analyzed with finite element analysis by LS-DYNA3D. The analysis proposes the sequential die and part shapes with the corresponding punch force and dimensional accuracy. The analysis also considers the effect of elastic dies on the dimensional accuracy of the formed parts. The analysis result demonstrates that the elastic analysis in the milli-forming process is indispensable fur accurate forming analysis. The analysis procedure in the paper will provide good information in design of a new micro-former and milli-component.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.