• 동력기계공학회지
• /
• 제3권4호
• /
• pp.28-35
• /
• 1999

An application of scroll compressor to the residential air conditioning and heat pump markets has generated many reliability problem, especially abnormal noise. Most of these noise problems is due to the check valve and compliance between FS(Fixed Scroll) and OS(Orbiting Scroll). FS and OS are the main parts of scroll compressor and are the main pumping part. But check valve has the role of protection of reverse rotation of OS when power is off. Check valve have several noise problems. Among them, shut down noise and valve movement noise is more than severe than any other problem. In this paper covers with these two noise problem.

• 한국전자파학회논문지
• /
• 제11권2호
• /
• pp.228-233
• /
• 2000

본 논문에서는 무선광연결에서 끈사적 평균잡음검출을 이용한 차동검출방식에 대하여 소개한다 이 방식은 기존의 잠음광의 영향을 소거하는 차동검출기의 기능을 보완한다. 근사적 평균잡음전압을 이용하여 차동검출하면. 물체나 사람의 이동에 의하여 나타날 수 있는 잡음광 결합비의 순간적 변화에 의한 출력전압의 변동을 줄일 수 있다 이 것은 장음광의 공간적 분포가 수시로 변동하는 환경에서 무선광연결을 구성하는 경우 잡음광을 소거하는 데에 매우 효과적이다

• 한국소음진동공학회논문집
• /
• 제11권8호
• /
• pp.331-337
• /
• 2001

The purpose of this study is to analyze the principal causes of vibration problem and find out the method of vibration reduction in a chip-mount system. The principal causes are investigated through measurements of vibration spectrum and model parameters. Modal parameters are obtained by using an experimental model test. Based on the model parameters from experiments. a model of finite element method is formulated. The model presents effective redesign of increasing the natural frequencies in order to reduce the vibration of a chip-mount system. Further, through computer simulation for the behavior of head to be main vibration source, the best acceleration pattern of head movement can be verified to achieve effective head-positioning and reduce the vibration due to head movement.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.883-889
• /
• 2005

Micro robots have been developed for many applications: medical, industrial, military, and so on. A small mobile robot was built and it has three legs made of bimorph piezoelectric actuators. It proceeds by vibrating the rear leg and it rotates by vibrating one of the front legs. The locomotion of the robot is described by relative position of mass center and the friction between the legs and the floor. This paper describes the principles of locomotion and modeling of the robot Modeling was simulated to investigate the dynamics of its mobility. The simulation results verified the modeling by showing similar movement of the robot as measured. It remained, however, several problems through experiments such as crooked direction of forward movement and proceeding speed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.343-347
• /
• 2008

Design of shape for visco-elastic vibration isolation elements, which are very cost-effective and so popular in many applications is frequently based on experiences, intuitions, or trial and errors. Such traditions in shape design make it difficult for drastic changes or new concepts to come out. In this paper, both topological method and shape optimization method are combined together to find out a most desirable isolator shape efficiently by using two commercial engineering programs. ABAQUS and MATLAB. The procedure is divided into two steps. At the first step, a topology optimization method is employed to find an initial shape. where density of either 0 or 1 for finite elements is used for physical realizability. At the second step, based on the initial shape, finer tuning of the shape is done by boundary movement method. An illustration of the procedure will be presented for a mount of an air-conditioner compressor system and the effectiveness will be discussed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.140-145
• /
• 2002

In high-capacity disk drives with ever-growing track density, the allowable level of position error signal (PES) is becoming smaller and smaller. A substantial portion of the PES is caused by disk vibration. This can be reduced by using a head gimbal assemblies (HGAs) that do not confine the slider movement to the vertical direction to disks, but allow movement to the radial direction of disks with respect to disk vibration. Several types of HGAs are proposed for such radial motion of the slider. Experimental results show that the PES levels are reduced by the proposed HGA-design concepts.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1994년도 Proceedings of the Korea Automatic Control Conference, 9th (KACC) ; Taejeon, Korea; 17-20 Oct. 1994
• /
• pp.601-604
• /
• 1994

This paper describes an effective method to estimate a position of an automous vehicle equipped with a single CCD-camera along indoor passageways. Using the sequential image data from the self-movement of the vehicle, the position is estimated by integrating the approximated motion parameters. The detection of the yaw angle that is one of the motion parameter is difficult in general, e.g. slip or error for noise, therefore the different detection is presented, which is, without shaft encoders, based on a projection function for 2D-image data and a cross-correlation function so as to be robust for noise. The approximated geometric function to estimate the position is used to reduce the computational effort. To verify the effectiveness of the method, the analysis and the computational results are shown through the simulations. Furthermore, the experimental results by using the test vehicle for the real indoor passageway are shown.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.387-392
• /
• 2002

A portable mould oscillation analyzer with an integrated computer, developed by POSCO, records the movement of the mould in every spatial direction. The system uses the gap sensors to measure the mould movement (displacement) in two horizontal directions according to the mould narrow and broad faces and the vertical strokes in the four corners of mould. The gap sensor is a non-contacting minute displacement-measuring device using the principle of high frequency eddy current loss. The mould oscillation diagnostic system integrates the gap sensors, their converters and the industrial portable computer with plug-in data acquisition boards. In an own expert module, which is included in the diagnosis program, one can obtain much information about the mould oscillation equipment.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.667-669
• /
• 2014

Development of 3 cylinder turbo charger engine is increasing due to engine down-sizing, cost reduction and emission regulations. However, 3 cylinder engine makes higher Exhaust manifold gas pressure(P3) pulsation than 4 cylinder engine and it generate boosting air with high pulsation. The mechanical waste-gate turbocharger just controlled by the boosting air has higher movement because of this high pulsation boosting air. This causes high vibrations to wasted gate and accelerate wear of the linkage system. So we need to understand out of the exhaust gas pressure pulsation changed by turbocharger compressor pressure(P2) Pulsation. In this study, we discuss how to prevent to abnormal movement of the turbo actuator by stabilized P2 Pulsation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.840-845
• /
• 2004

Development of the linear motors is recently required to control a high-speed and high-resolution in the high-integrated and speed process industry. This paper presents vibration analyses as well as measurement standards of the newly developed linear motors through analyzing the vibration characteristics of the advanced products. Vibration experiments are conducted for identifying vibration level during operation. They are also included in the modal test to analyze dynamic characteristics. Analytic data using Finite Element Method (FEM) are compared with the results of the modal. The FEM and experiments make it possible to understand these characteristics. Further, through computer simulation for the behavior of moving part to be vibration source, the best acceleration pattern of moving part movement can be verified to achieve effective moving part positioning and reduce the vibration due to moving part movement.