• Journal of electromagnetic engineering and science
• /
• 제3권2호
• /
• pp.118-125
• /
• 2003

This paper presents a 5.8-㎓ oscillator that uses a novel defected ground structure(DGS), which is etched on the metallic ground plane. As the suggested defected ground structure is the structure for mounting an active device, it is the roles of a feedback loop inducing a negative resistance as well as a frequency-selective circuit. Applying the feedback loop between the drain and the gate of a FET device produces precise phase conversion in the feedback loop. The equivalent circuit parameters of the DGS are extracted by using a three-dimensional EM simulation ,md simple circuit analysis method. In order to demonstrate a new DGS oscillator, we designed the oscillator at 5.8-㎓. The experimental results show 4.17 ㏈m output power with over 22 % dc-to-RF power efficiency and - 85.8 ㏈c/Hz phase noise at 100 KHz offset from the fundamental carrier at 5.81 ㎓.

• 한국산업융합학회 논문집
• /
• 제23권5호
• /
• pp.825-833
• /
• 2020

Currently, the K-Water uses various valves that can be remotely controlled for optimal water management. Valve system fault can be classified into rotor defects, stator defects, bearing defects, and gear defects of induction motors. If the valve cannot be operated due to a gear fault, the water management operation can be greatly affected. For effective water management, there is an urgent need for preemptive repairs to determine whether gear is damaged through failure prediction diagnosis.. Recently, deep learning algorithms are being applied for valve failure diagnosis. However, the method currently applied has a disadvantage of attaching a vibration sensor to the valve. In this paper, propose a new algorithm to determine whether a fault exists using a convolutional neural network (CNN) based on the voltage and current information of the valve without additional sensor mounting. In particular, a normalized Lisasjous diagram was used to maximize the fault classification performance in the CNN-based diagnostic system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.345-350
• /
• 2001

Dynamic behavior of high speed train is very important because the high speed train should be safe and satisfied with the ride comfort. An eddy current brake system is mounted on trailer bogie and wheelset. The eddy current braking force longitudinally exerts on the articulated trailer bogie and the attraction force vertically exerts on the wheelset. Because a frame of eddy current brake system is flexible, these forces generate the vertical vibration at middle point of the frame. Also, the vibration change the vertical clearance between an electromagnet and top of rail which affect the magnitude of braking and attracting forces. Therefore, the dynamic behavior of the eddy current braking system must be predicted for design the dynamic characteristic of its mounting system when normally operate on rail which have irregularity. Vampire program is used for prediction of the dynamic behavior of an eddy current braking system. Five design variables and five performance index are considered for optimization through D-optimal experimental design in this paper. Also model center is used to search the optimal point for sum of performance index with variational matric method.

• 대한기계학회논문집
• /
• 제18권8호
• /
• pp.2158-2166
• /
• 1994

In order to understand the package crack emanating from the edge of leadframe after the delamination between leadframe and epoxy molding compound in an electronic packaging of surface mounting type, the M-integral and J-integral in fracture mechanics are obtained. The effects of geometry, material properties and molding process temperature on the package crack are investigated taking into account the temperature dependence of the material properties, which simulates a more realistic condition. If the temperature dependence of the material properties is considered the result of analysis conforms with observations that the crack is kinked at between 50 and 65 degree. However, in case of constant material properties at the room temperature it is found that the J-integral is underestimated and the kink crack angle is different form the observation. The effects of the material properties and molding process temperature on J-integral and crack angle are less significant that the chip size for the cases considered here. It is suggested that the geometric factors such as ship size, leadframe size are to be well designed in order to prevent(or control) the occurrence and propagation of the package crack.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.404-409
• /
• 2004

To maximize the productivity in machining molds and dies, machine tools should operate at high speeds. During the high speed operation of moving frames or spindles, vibration problems are apt to occur if the machine tool structures are made of conventional steel materials with inferior damping characteristics. However, self-excited vibration or chatter is bound to occur during high speed machining when cutting speed exceeds the stability limit of machine tool. Chatter is undesirable because of its adverse effect on surface finish, machining accuracy, and tool life. Furthermore, chatter is a major cause of reducing production rate because, if no remedy can be found, metal removal rates have to be lowered until vibration-free performances is obtained. Also, the resonant vibration of machine tools frequently occurs when operating frequency approaches one of their natural frequencies because machine tools have several natural frequencies due to their many continuous structural elements. However, these vibration problems are closely related to damping characteristics of machine tool structures. The polymer concrete has high potential for machine tool bed due to its good damping characteristics with moderate stiffness. This paper presents the use of polymer concrete and sandwich structures to overcome vibration problems. Also, co-cure bonding method for functional part mounting was exhibited experimentally, by which manufacturing time and cost for polymer concrete bed will be remarkably reduced.

• 대한기계학회논문집
• /
• 제18권8호
• /
• pp.2139-2157
• /
• 1994

In order to understand the delamination between leadframe and epoxy molding compound in an electronic packaging of surface mounting type, the stress intensity factor, T-stress and J-integral in fracture mechanics are obtained. The effects of geometry, material properties and molding process temperature on the delamination are investigated taking into account the temperature dependence of the material properties, which simulates as more realistic condition. As the crack length increases the J-integral increases, which suggest that the crack propagates if it starts growing from the small size. The effects of the material properties and molding process temperature on stress intensity factor, T-stress is and J-integral are less significant than the chip size for the practical cases considered here. The T-stress is negative in all eases, which is in agreement with observation that interfacial crack is not kinked until the crack approaches the edge of the leadframe.

• Tribology and Lubricants
• /
• 제12권4호
• /
• pp.28-34
• /
• 1996

The lubrication characteristics of high-speed ball bearings have been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flow rates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 2969 N axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• 한국산학기술학회논문지
• /
• 제11권10호
• /
• pp.3935-3941
• /
• 2010

초고속 통신망의 발달로 네트워크 보안 및 시스템 해킹 사고에 대응하기 위한 다양한 인증 및 접근 제어 시스템이 도입되고 있다. 그러나 실제로 초고속 통신망에서는 정보 보호를 위한 보안 자체가 취약성을 보이고 있다. 따라서 기존 사용자의 다양한 욕구를 충족시키고 보다 안전하고 신뢰성있는 새로운 인증 시스템의 도입이 필요하다. 이에 본 논문에서는 접근 권한(Explicit 인증, Implicit 인증) 및 보안성이 우수한 인증방법을 제시하고 스몰망을 통해 우수함을 보이고자 한다.

• 한국전자통신학회논문지
• /
• 제15권3호
• /
• pp.451-456
• /
• 2020

본 논문에서는 JTDLS 완성형 항공기에 장착하기 위한 내장형 안테나 설계 방법에 대해 연구하였다. 제안된 안테나는 MIDS-LVT 운용 대역을 충족하고, 확장성을 고려하여 광대역으로 설계하였다. 설계결과, 제안된 안테나는 기존 블레이드 안테나와 전기적 성능은 유사하고, 광대역 특성임을 확인하였다. 항공기 장착성을 확인하기 위해 항공기 상/하부에 안테나를 장착하여 EM 분석한 결과, 상/하부 모두 양호한 복사특성을 나타내는 것을 확인하였다. 본 연구를 통해 획득한 기술은 JTDLS 완성형 항공기에 활용 가능할 것으로 판단된다.

• 한국입자에어로졸학회지
• /
• 제11권4호
• /
• pp.93-98
• /
• 2015

Particles which generated from plasma enhanced chemical vapor deposition (PECVD) during thin film deposition process can affect to the process yield. By using light extinction method, ISPM can measure particles in the large-diameter pipe (${\leq}300mm$). In our research, in-situ particle monitor (ISPM) sensor was installed at the 300 mm diameter exhaust-line to count the particles in each size. In-house flange for mounting the transmitting and receiving parts of ISPM was carefully designed and installed at a certain point of exhaust line where no plasma light affect to the light extinction measurement. Measurement results of trend changes on particle count in each size can confirm that ISPM is suitable for real-time monitoring of vacuum process.